The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 04-18-2015, 10:09 PM   #1
65standard
Registered User
 
65standard's Avatar
 
Join Date: Dec 2014
Location: Coal City, IL
Posts: 695
A different approach to a LWB to SWB conversion

Since I needed to pull the bed on my 1970 C20 to do cab corners, I decided to make it a short bed too. My approach is different than the conversions I see most doing on this site. As a metal shaper, we are taught to plan out our cuts and splices to ease fabrication, save time, and avoid frustration later on. So I came up with a better idea to make cuts and seams easier to do and keep the original paint, well most of it. Here is my plan:

Before:



First remove the bed. I just cut all 8 bolts and unplugged the rear harness.



Remove 8" from rear of frame rails and move the slot on top forward too.



Then remove the front most bed mounting bracket.





Then remove the front rivet of the second bracket and swing out of way. Then mark the cut. I went from the front rivet hole of the front bracket to the front rivet hole of the second brackets.



Then I unbolted the trailing arms from the crossmember, removed all rivets from crossmember and slid it forward 12". I welded in place. Then I cut the frame rails.



To be continued...
__________________
Tony Nicholas @ Midwest Metal Masters

1953 Chevy 3100 392 Hemi w/727 & 9” Ford
1985 Chevy C/10 6.0L 4L80 373 locker
65standard is offline   Reply With Quote
Old 04-18-2015, 11:41 PM   #2
cooperhw
Registered User
 
cooperhw's Avatar
 
Join Date: Oct 2014
Location: Mesa AZ (Near Phoenix)
Posts: 2,302
Re: A different approach to a LWB to SWB conversion

Interesting.

More than one way to skin a cat.
__________________
"Life is too short to drive a boring vehicle".
Later,
Wayne
cooperhw is offline   Reply With Quote
Old 04-18-2015, 11:44 PM   #3
dacavy
Registered User
 
Join Date: Sep 2014
Location: meridian, idaho
Posts: 95
Re: A different approach to a LWB to SWB conversion

I shortened the frame right behind the cab just like you did. The only difference was I put a 2" step notch. Sure makes it easier if you dont want to pull the cab off.
dacavy is offline   Reply With Quote
Old 04-18-2015, 11:53 PM   #4
dacavy
Registered User
 
Join Date: Sep 2014
Location: meridian, idaho
Posts: 95
Re: A different approach to a LWB to SWB conversion

My cut behind the cab
Attached Images
 
dacavy is offline   Reply With Quote
Old 04-19-2015, 08:56 AM   #5
65standard
Registered User
 
65standard's Avatar
 
Join Date: Dec 2014
Location: Coal City, IL
Posts: 695
Re: A different approach to a LWB to SWB conversion

Then I carefully aligned the rails and tack welded them together.



Next did a full penn weld and ground it down so it could be tested. Then swung the bed mounts back.





Cut the front drive shaft down, exhaust, and brake line.



Then drove it out to take a look and the new profile.



Next comes the bed...
__________________
Tony Nicholas @ Midwest Metal Masters

1953 Chevy 3100 392 Hemi w/727 & 9” Ford
1985 Chevy C/10 6.0L 4L80 373 locker
65standard is offline   Reply With Quote
Old 04-19-2015, 09:04 AM   #6
msgross
Registered User
 
msgross's Avatar
 
Join Date: Jul 2006
Location: Central PA
Posts: 12,201
Re: A different approach to a LWB to SWB conversion

Nice work... does that frame need any more reinforcement in the weld area? I see a lot of people use a plate behind it.
__________________
The Garage:
1968 K-10 SWB - "Project Money Pit"
1996 Z-71 - "huntin rig"
1969 C-10 LWB (SOLD) "Project flip that truck or else"
1993 Passport, F@rd 1-ton (SOLD)"Project Cousin Eddie"


My Garage Build "The 1,000 footer"
msgross is offline   Reply With Quote
Old 04-19-2015, 09:17 AM   #7
LockDoc
The Older Generation

 
LockDoc's Avatar
 
Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,270
Re: A different approach to a LWB to SWB conversion

Quote:
Originally Posted by 65standard View Post
Then I carefully aligned the rails and tack welded them together.

Next did a full penn weld and ground it down so it could be tested. Then swung the bed mounts back.

Cut the front drive shaft down, exhaust, and brake line.

Then drove it out to take a look and the new profile.

Next comes the bed...

95% of the people that read your thread are not going to have a clue what a penn weld is (including me) and what you mean by being "tested". I did a Google search for "penn weld" and not much came up.

Also wondering if you plated the inside of the frame at all.

Just personal preference I guess, but I would never use a straight cut to shorten a frame.

Thanks,
LockDoc
__________________
Leon

Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles

(My Dually Pickup Project Thread)

http://67-72chevytrucks.com/vboard/s...d.php?t=829820

-
LockDoc is offline   Reply With Quote
Old 04-19-2015, 09:38 AM   #8
shawno72
C/10 junkie
 
shawno72's Avatar
 
Join Date: Nov 2010
Location: Stockton Ca
Posts: 9,093
Re: A different approach to a LWB to SWB conversion

Quote:
Originally Posted by LockDoc View Post
95% of the people that read your thread are not going to have a clue what a penn weld is (including me) and what you mean by being "tested". I did a Google search for "penn weld" and not much came up.

Also wondering if you plated the inside of the frame at all.

Just personal preference I guess, but I would never use a straight cut to shorten a frame.

Thanks,
LockDoc
Full penetration weld. Means there is 100% weld joining the 2 piece of metal instead of just butting the 2 pieces together. You can see he has a slight gap between the frame rails, then he adds a small piece of metal to one side and uses weld to join it together. Hope that helps

Great work btw
__________________
Shawn

70 LWB C10 current driver/project
http://67-72chevytrucks.com/vboard/s...d.php?t=663051
68 SWB C10 Work in progress.....SOLD
http://67-72chevytrucks.com/vboard/s...d.php?t=559520
72 LWB C10 Sold
71 LWB C10 Sold
68 LWB C10 CST Sold


http://youtu.be/kbB0QrBIs9k

My mom always had the best advice. It was just a tad late. After a fall that involved blood, she'd say....."Careful!"
shawno72 is offline   Reply With Quote
Old 04-19-2015, 09:40 AM   #9
oldertruckfan
Registered User
 
Join Date: Mar 2014
Location: Spring Hill Kansas
Posts: 209
Re: A different approach to a LWB to SWB conversion

penn weld is a full penetration weld. tested would mean that a certified weld inspector would check the weld for full penetration using some method of testing
oldertruckfan is offline   Reply With Quote
Old 04-19-2015, 09:48 AM   #10
65standard
Registered User
 
65standard's Avatar
 
Join Date: Dec 2014
Location: Coal City, IL
Posts: 695
Re: A different approach to a LWB to SWB conversion

95% of the people will not like my frame since I am not added any fish plate. A full penetration weld is just that, the weld bead is the full thickness of the material. This is done by beveling the rails and leaving a small gap before welding. Once welded, you will have a raised bead on both sides of the rail.

I then ground down the weld so it could be tested. A machine like an ultrasound and jelly is used to look for and air gaps or disturbances in the metal. Also, grinding the weld smooth avoids any stress spots or sharp edges.

If the weld was not 100%, I would add a brake formed channel to fit inside the rail. This is much better than a fish plate or boxing plate.

Now, off to the bed. I completely disassembled the bed and cut down the floor pan. 12" off the front and 7.5" off the rear.



I drilled new front and rear mounting holes in the pan and bolted it to the frame.

You can see it still looks factory.


For the rear, I saved the rear cross sill and put it back on the frame and under the pan.



Then I started to tip over the 1/2" of floor pan I saved when I cut 7.5" off.



Once fully tipped, I plug welded the pan back down to the cross sill. The floor is now a SWB pan and no splicing like all others I have seen here. I saved over 10' of weld and kept my original paint.






Now off to the bed sides....
__________________
Tony Nicholas @ Midwest Metal Masters

1953 Chevy 3100 392 Hemi w/727 & 9” Ford
1985 Chevy C/10 6.0L 4L80 373 locker
65standard is offline   Reply With Quote
Old 04-19-2015, 10:09 AM   #11
bollybib
Registered User
 
bollybib's Avatar
 
Join Date: Nov 2010
Location: Carlsbad, CA
Posts: 1,584
Re: A different approach to a LWB to SWB conversion

Interesting. Looking forward to seeing how you do the bed.
__________________
- Jim -

My Daily Driver is a 1969 Chevrolet Custom/20 Fleetside 350/TH400/Eaton H052 4.10
and its Project thread is here http://67-72chevytrucks.com/vboard/s...d.php?t=456911
bollybib is offline   Reply With Quote
Old 04-19-2015, 10:29 AM   #12
29od1
Senior Member
 
Join Date: Oct 2006
Location: Wichita, Kansas
Posts: 1,050
Re: A different approach to a LWB to SWB conversion

What's your plan for the front of the bed floor where the front bed panel attaches? Will you form all the beads flat where the two bolt together?
29od1 is offline   Reply With Quote
Old 04-19-2015, 10:40 AM   #13
65standard
Registered User
 
65standard's Avatar
 
Join Date: Dec 2014
Location: Coal City, IL
Posts: 695
Re: A different approach to a LWB to SWB conversion

No. I didn't see the need to flatten the pan where the bulk head bolt down. I will just re drill the bolts between the ribs of the pan.

I am aiming to keep as much of the original paint and rust as possible. I do not want two huge weld seam on the sides of the bed. I can't keep the original paint or finish the weld that way. It would surely require bondo and new paint with that cut down method.
__________________
Tony Nicholas @ Midwest Metal Masters

1953 Chevy 3100 392 Hemi w/727 & 9” Ford
1985 Chevy C/10 6.0L 4L80 373 locker
65standard is offline   Reply With Quote
Old 04-19-2015, 11:42 AM   #14
tommys72
Registered User
 
tommys72's Avatar
 
Join Date: Jun 2012
Location: springfield mo
Posts: 3,075
Re: A different approach to a LWB to SWB conversion

I'm pretty much amazed so far. I'm looking forward to the bed work
__________________
United States Marine Corps 2000-2011
Iraq and Afghanistan veteran
Just living life now and enjoying it and my wife, daughter and son


tommys72 is offline   Reply With Quote
Old 04-19-2015, 12:07 PM   #15
leftybass209
Registered User
 
leftybass209's Avatar
 
Join Date: Feb 2011
Location: Modesto, CA
Posts: 2,179
Re: A different approach to a LWB to SWB conversion

Quote:
Originally Posted by 65standard View Post
I am aiming to keep as much of the original paint and rust as possible. I do not want two huge weld seam on the sides of the bed. I can't keep the original paint or finish the weld that way. It would surely require bondo and new paint with that cut down method.
How do you plan on shortening the bed sides without weld seams while still retaining a factory short bed appearance?
leftybass209 is offline   Reply With Quote
Old 04-19-2015, 12:51 PM   #16
65standard
Registered User
 
65standard's Avatar
 
Join Date: Dec 2014
Location: Coal City, IL
Posts: 695
Re: A different approach to a LWB to SWB conversion

For the front of the bed I scribe two lines. My cut line at 11 1/8" and my tipping line at 12". More pictures as I go....
__________________
Tony Nicholas @ Midwest Metal Masters

1953 Chevy 3100 392 Hemi w/727 & 9” Ford
1985 Chevy C/10 6.0L 4L80 373 locker
65standard is offline   Reply With Quote
Old 04-19-2015, 01:28 PM   #17
57larry
Registered User
 
Join Date: Nov 2007
Location: Indianapolis
Posts: 1,160
Re: A different approach to a LWB to SWB conversion

looks like very nice work. waiting for more pics
57larry is offline   Reply With Quote
Old 04-19-2015, 02:10 PM   #18
aod92
Registered User
 
aod92's Avatar
 
Join Date: Dec 2014
Location: Plainfield il.
Posts: 643
Re: A different approach to a LWB to SWB conversion

Looks great! You work wonders with metal and it sure is fun to watch.
aod92 is offline   Reply With Quote
Old 04-19-2015, 02:51 PM   #19
shawno72
C/10 junkie
 
shawno72's Avatar
 
Join Date: Nov 2010
Location: Stockton Ca
Posts: 9,093
Re: A different approach to a LWB to SWB conversion

This is great info for when I shorten mine
__________________
Shawn

70 LWB C10 current driver/project
http://67-72chevytrucks.com/vboard/s...d.php?t=663051
68 SWB C10 Work in progress.....SOLD
http://67-72chevytrucks.com/vboard/s...d.php?t=559520
72 LWB C10 Sold
71 LWB C10 Sold
68 LWB C10 CST Sold


http://youtu.be/kbB0QrBIs9k

My mom always had the best advice. It was just a tad late. After a fall that involved blood, she'd say....."Careful!"
shawno72 is offline   Reply With Quote
Old 04-19-2015, 02:57 PM   #20
67swb72klb
Registered User
 
67swb72klb's Avatar
 
Join Date: Dec 2010
Location: livingston co.mi
Posts: 2,447
Re: A different approach to a LWB to SWB conversion

Some good ideas
__________________
California 65 GTO---Texas 64 burb 283 ---Oklahoma 67 CST SWB BBW wood bed 327 2004r---New Mexico 72 k10 350 350 auto---Georga 72 short step project
67swb72klb is offline   Reply With Quote
Old 04-19-2015, 03:54 PM   #21
72_K10_Vegas
Registered User
 
72_K10_Vegas's Avatar
 
Join Date: Mar 2014
Location: Las Vegas Nevada
Posts: 93
Re: A different approach to a LWB to SWB conversion

Nice
__________________
72 K10
72_K10_Vegas is offline   Reply With Quote
Old 04-19-2015, 04:21 PM   #22
treveiger
Senior Member
 
treveiger's Avatar
 
Join Date: Jul 2010
Location: South Dakota
Posts: 4,090
Re: A different approach to a LWB to SWB conversion

Looks great.
__________________
1969 Chevy c20(Miss Hackjob)
treveiger is offline   Reply With Quote
Old 04-19-2015, 05:52 PM   #23
65standard
Registered User
 
65standard's Avatar
 
Join Date: Dec 2014
Location: Coal City, IL
Posts: 695
Re: A different approach to a LWB to SWB conversion

The bulkhead will just bolt to the floor pan something like this. I will drill holes on the lows of the pan.



Here are my scribe lines on the front of the bed side. One for cutting and one for tipping over the edge.



I will tip the edge over just like the factory did here.


If I wanted to, I could just weld the bed side back together right at the edge. But I don't want to burn the paint if I don't have to.



Once I cut the extra material off, I started to tip over the inner panel. Again no welding here.



And started to tip over the outer bed skin.



With the inner panel fully tipped, I slid the end cap in place to see my progress.




Test fit is looking good. I just need to complete tipping the outer skin to the end cap, spot weld back together and add the front bed pocket to finish up this corner.


100% of the original paint save and 17' of weld avoided so far.
__________________
Tony Nicholas @ Midwest Metal Masters

1953 Chevy 3100 392 Hemi w/727 & 9” Ford
1985 Chevy C/10 6.0L 4L80 373 locker
65standard is offline   Reply With Quote
Old 04-19-2015, 05:59 PM   #24
tommys72
Registered User
 
tommys72's Avatar
 
Join Date: Jun 2012
Location: springfield mo
Posts: 3,075
Re: A different approach to a LWB to SWB conversion

Damn fine work fella! Nice and original looking
__________________
United States Marine Corps 2000-2011
Iraq and Afghanistan veteran
Just living life now and enjoying it and my wife, daughter and son


tommys72 is offline   Reply With Quote
Old 04-19-2015, 06:01 PM   #25
imjeff
Registered User
 
imjeff's Avatar
 
Join Date: Feb 2008
Location: Tacoma Washington
Posts: 890
Re: A different approach to a LWB to SWB conversion

I'm kind of curious how your frame will do without fish plating it. You have two brittle lines running up your frame. Fish plating spreads that stress over multiple areas. It's not a matter of whether the weld is completely penetrated, it's the stress on the toes of the weld. Without heat treating, those toes will be weaker than the weld or the unheated frame.

Jeff
__________________
I know a guy who's addicted to brake fluid. He says he can stop any time.
72 K10 396
75 Cj5 MPI 350 Chev
67 Chevelle 396, 4 speed
74 FXE
08 Tahoe
imjeff is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 08:14 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com