|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
11-30-2013, 10:49 PM
|
#1 |
|
Registered User
Join Date: Mar 2005
Location: Melissa, TX
Posts: 799
|
71 3/4 ton parts on 67 1/2 ton?
So I have a 67 short-step 1/2 ton with coils.
I am working a deal to get a 71 3/4 ton with leafs from my mom. I know I can use the motor, A/C, PS, PB body parts etc... But, is it possible to convert the beefy rear end in the 3/4 ton to 5 lug and put it in my truck? I will be using the 396 from the 71.
__________________
68 short bed driver (71 clip on it now, swapping to 68 when weather cooperates) 67 short step project (will get SWB from the 68) 67 Camaro, #'s matching (my wife's) 03 Dodge Ram 2500 4x4 diesel 5 speed 4.10 rear |
|
|
|
12-01-2013, 09:01 AM
|
#2 |
|
Special Order
  
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,862
|
Re: 71 3/4 ton parts on 67 1/2 ton?
The way I'd go about that is convert the axle to coil. That would be easier than swapping the suspensions and you'd keep your ride about the same. That rear should be a Dana60 3.54:1 ratio.
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
|
|
|
|
12-01-2013, 11:41 AM
|
#3 |
|
Registered User
Join Date: Mar 2005
Location: Melissa, TX
Posts: 799
|
Re: 71 3/4 ton parts on 67 1/2 ton?
Does anyone make an axle swap to convert the 8 lug to 5 lug?
__________________
68 short bed driver (71 clip on it now, swapping to 68 when weather cooperates) 67 short step project (will get SWB from the 68) 67 Camaro, #'s matching (my wife's) 03 Dodge Ram 2500 4x4 diesel 5 speed 4.10 rear |
|
|
|
|
12-01-2013, 12:52 PM
|
#4 |
|
Registered User
Join Date: Mar 2005
Location: Melissa, TX
Posts: 799
|
Re: 71 3/4 ton parts on 67 1/2 ton?
Never mind. I wasn't aware of the design of the 3/4 ton rear end. I can just swap the hubs to 5-5.5
__________________
68 short bed driver (71 clip on it now, swapping to 68 when weather cooperates) 67 short step project (will get SWB from the 68) 67 Camaro, #'s matching (my wife's) 03 Dodge Ram 2500 4x4 diesel 5 speed 4.10 rear |
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
