cheyenne-10 & super emblem location - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**pjmoreland** · 08-16-2023, 09:56 AM

I'd say the fender doesn't need to come off, but the Cheyenne badge does. Removing the inner fender makes it much easier to remove the badge.

**Rich72C10** · 08-16-2023, 10:20 AM

Quote:

Originally Posted by pjmoreland

I'd say the fender doesn't need to come off, but the Cheyenne badge does. Removing the inner fender makes it much easier to remove the badge.

I have heard that but it seems like there's more pain with the inner, like with the heater hoses on the right side? I never done either, so its all a mystery to me. Plus I want to get my dust shields in and the fender 100% has to come off for that!

Speaking of which, pjmoreland could you take a look at my photo in my Rebuilding / Installing Hinge Pillar to Fender Seal thread (post #12)?

**Rich72C10** · 08-16-2023, 10:43 AM

Hey pjmoreland, you mentioned it is a nice idea to pull the clip to get to my seals but if I was to go that route - would we be able to get to the Cheyenne emblem with the whole clip? Which I think means the inner fenders stay on.

Sorry if that is a stupid question, I just don't know these things.

**pjmoreland** · 08-16-2023, 10:56 AM

You'd definitely be able to get to the emblems with the front clip removed and the inner fenders still installed. The rear of the emblems are covered up by the cab, and the cab would be out of the picture.

**Rich72C10** · 08-16-2023, 10:59 AM

Quote:

Originally Posted by pjmoreland

You'd definitely be able to get to the emblems with the front clip removed and the inner fenders still installed. The rear of the emblems are covered up by the cab, and the cab would be out of the picture.

Sweet, I hate being so ignorant - thank you.

**Rich72C10** · 08-16-2023, 02:18 PM

Actually, back to just the fender route - I don't want to be messing with my AC connections and bits to get the clip off.

**pjmoreland** · 08-16-2023, 02:41 PM

Quote:

Originally Posted by Rich72C10

Actually, back to just the fender route - I don't want to be messing with my AC connections and bits to get the clip off.

Good point!

**Rich72C10** · 11-21-2023, 05:08 PM

My brother's paint & body guy stopped by just after I had taped/marked holes for my super badge. So the passenger side is drilled and mouted!

Then he went over to the driver's side, which is still on and said I'll get this one drilled now. I reported, well I am not ready to pull that fender. He said, no problem I'll eyeball it. Just give me your tape, pencil, ruler. Gee, so glad he came by!

**Rich72C10** · 11-22-2023, 09:34 PM

Photos of job done, YAY!

**General23cmp** · 11-23-2023, 12:17 AM

Well done. I see so many “super” emblems oriented wrong at car shows. “Super” always aligns to the left. Great job.

**Rich72C10** · 11-23-2023, 08:41 AM

Thank you, getting help here in the forums insured that it was done properly. I also was "super" lucky my brother's body/paint guy popped into his shop for a visit.

He really did impress me when he did the driver's side with the fender still on the truck. Drilling into my truck was freaking me out and in the end I avoided it! LOL!

**Dieselwrencher** · 11-28-2023, 07:54 AM

Richard, it looks very nice!

08-16-2023, 09:56 AM	#26
pjmoreland Senior Member Join Date: Jan 2005 Location: CA Posts: 5,300	Re: cheyenne-10 & super emblem location I'd say the fender doesn't need to come off, but the Cheyenne badge does. Removing the inner fender makes it much easier to remove the badge.

08-16-2023, 10:43 AM	#28
Rich72C10 Mr. Cheyenne Join Date: Jun 2020 Location: Kyle, Texas Posts: 1,643	Re: cheyenne-10 & super emblem location Hey pjmoreland, you mentioned it is a nice idea to pull the clip to get to my seals but if I was to go that route - would we be able to get to the Cheyenne emblem with the whole clip? Which I think means the inner fenders stay on. Sorry if that is a stupid question, I just don't know these things. __________________ Richard *'72 Chevy C10 Cheyenne Super WHT/MED BRONZE/WHT SBC 350 \| TH350 \| LWB \| AC \| Buddy Seats Upgrades:** Tilt \| Front Sway Bar \| Radio \| Sliding Window \| Bed Spare w/Lock Bed Rails \| Full LEDs \| Courtesy Lights \| Tachometer \| Glovebox Lock & Light \| Head Light Relays \| *Upgraded Fully Super Trim

08-16-2023, 10:56 AM	#29
pjmoreland Senior Member Join Date: Jan 2005 Location: CA Posts: 5,300	Re: cheyenne-10 & super emblem location You'd definitely be able to get to the emblems with the front clip removed and the inner fenders still installed. The rear of the emblems are covered up by the cab, and the cab would be out of the picture.

08-16-2023, 02:18 PM	#31
Rich72C10 Mr. Cheyenne Join Date: Jun 2020 Location: Kyle, Texas Posts: 1,643	Re: cheyenne-10 & super emblem location Actually, back to just the fender route - I don't want to be messing with my AC connections and bits to get the clip off. __________________ Richard *'72 Chevy C10 Cheyenne Super WHT/MED BRONZE/WHT SBC 350 \| TH350 \| LWB \| AC \| Buddy Seats Upgrades:** Tilt \| Front Sway Bar \| Radio \| Sliding Window \| Bed Spare w/Lock Bed Rails \| Full LEDs \| Courtesy Lights \| Tachometer \| Glovebox Lock & Light \| Head Light Relays \| *Upgraded Fully Super Trim

11-21-2023, 05:08 PM	#33
Rich72C10 Mr. Cheyenne Join Date: Jun 2020 Location: Kyle, Texas Posts: 1,643	Re: cheyenne-10 & super emblem location My brother's paint & body guy stopped by just after I had taped/marked holes for my super badge. So the passenger side is drilled and mouted! Then he went over to the driver's side, which is still on and said I'll get this one drilled now. I reported, well I am not ready to pull that fender. He said, no problem I'll eyeball it. Just give me your tape, pencil, ruler. Gee, so glad he came by! Attached Images __________________ Richard *'72 Chevy C10 Cheyenne Super WHT/MED BRONZE/WHT SBC 350 \| TH350 \| LWB \| AC \| Buddy Seats Upgrades:** Tilt \| Front Sway Bar \| Radio \| Sliding Window \| Bed Spare w/Lock Bed Rails \| Full LEDs \| Courtesy Lights \| Tachometer \| Glovebox Lock & Light \| Head Light Relays \| *Upgraded Fully Super Trim

11-22-2023, 09:34 PM	#34
Rich72C10 Mr. Cheyenne Join Date: Jun 2020 Location: Kyle, Texas Posts: 1,643	Re: cheyenne-10 & super emblem location Photos of job done, YAY! __________________ Richard *'72 Chevy C10 Cheyenne Super WHT/MED BRONZE/WHT SBC 350 \| TH350 \| LWB \| AC \| Buddy Seats Upgrades:** Tilt \| Front Sway Bar \| Radio \| Sliding Window \| Bed Spare w/Lock Bed Rails \| Full LEDs \| Courtesy Lights \| Tachometer \| Glovebox Lock & Light \| Head Light Relays \| *Upgraded Fully Super Trim

11-23-2023, 12:17 AM	#35
General23cmp Registered User Join Date: Mar 2016 Location: Athens, AL Posts: 349	Re: cheyenne-10 & super emblem location Well done. I see so many “super” emblems oriented wrong at car shows. “Super” always aligns to the left. Great job.

11-23-2023, 08:41 AM	#36
Rich72C10 Mr. Cheyenne Join Date: Jun 2020 Location: Kyle, Texas Posts: 1,643	Re: cheyenne-10 & super emblem location Thank you, getting help here in the forums insured that it was done properly. I also was "super" lucky my brother's body/paint guy popped into his shop for a visit. He really did impress me when he did the driver's side with the fender still on the truck. Drilling into my truck was freaking me out and in the end I avoided it! LOL! __________________ Richard *'72 Chevy C10 Cheyenne Super WHT/MED BRONZE/WHT SBC 350 \| TH350 \| LWB \| AC \| Buddy Seats Upgrades:** Tilt \| Front Sway Bar \| Radio \| Sliding Window \| Bed Spare w/Lock Bed Rails \| Full LEDs \| Courtesy Lights \| Tachometer \| Glovebox Lock & Light \| Head Light Relays \| *Upgraded Fully Super Trim

11-28-2023, 07:54 AM	#37
Dieselwrencher 6>8 Plugless........ Join Date: Sep 2007 Location: Prairie City, Ia Posts: 17,133	Re: cheyenne-10 & super emblem location Richard, it looks very nice! __________________ Ryan 1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread 1972 GMC Sierra Grande Longhorn 4x4 1972 Chevy Cheyenne Super K20 Long Step side tilt, tach, tow hooks, AC, 350 4 speed 1972 C10 Suburban Custom Deluxe 1969 Chevy milk truck 1971 Camaro RS 5.3 BTR STG3 Cam Super T10 1940 Ford 354 Hemi 46RH Ford 9" on air ride huge project *Tired of spark plugs? Check this out.*



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.