|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
03-20-2011, 08:29 AM
|
#1 |
|
Registered User
Join Date: Nov 2004
Location: Lindenhurst, IL
Posts: 659
|
Gap between the rocker and the bedside
Can any of you original paint guys tell me what the factory did with this gap between the rear of the rocker panel and the bottom of the bedside? Is it filled in with seam sealer or is it left open?
OR, maybe a better question is, what is the best thing to do here? |
|
|
|
03-20-2011, 08:44 AM
|
#2 |
|
GEARHEAD
Join Date: Aug 2003
Location: MN
Posts: 6,108
|
Re: Gap between the rocker and the bedside
Normally left as is.
__________________
If no one knows what you're doing, they can't tell you you're doing it wrong HG's Dream Car Build - Shelby Cobra Kit Build your own adjustable track bar 71  Long Fleet C/10 72  Jimmy 4x4 (Junkyard Jimmy)HG's Plow Truck '78  K35 DuallyBigass Farm Truck HG's thread of miscellaneous stuff |
|
|
|
|
03-21-2011, 05:29 PM
|
#3 |
|
Registered User
Join Date: Feb 2003
Location: Santa Ana, CA
Posts: 2,191
|
Re: Gap between the rocker and the bedside
No filler, left as is. Gap should be approximately the same as rear door edge to B-pillar gap.
|
|
|
|
|
03-21-2011, 06:59 PM
|
#4 |
|
SKINNY TIRES RULE!
Join Date: Sep 2001
Location: Bothell, WA
Posts: 11,049
|
Re: Gap between the rocker and the bedside
Here's some photos of mine that I have on my computer. Hopefully this shows you what you need.
__________________
bouncytruck 1972 K5 The Hauler 1994 K1500 Suburban The Daily2010 Kia Soul Wife's Ride2014 Fiat 500L |
|
|
|
|
03-21-2011, 09:04 PM
|
#5 |
|
toys'r'us
Join Date: Nov 2010
Location: Penticton, BC, Canada
Posts: 347
|
Re: Gap between the rocker and the bedside
tetnis shot!!!
__________________
71 jimmy bone stock 350 sm465 33x12.5 rallies 79 caprice landau full load crate350 th350 lowered 20"wires 00 f150 reg cab sb 4x4 5.4L Last edited by mustardjimmy71; 03-21-2011 at 09:07 PM. |
|
|
|
|
03-21-2011, 10:31 PM
|
#6 |
|
Registered User
Join Date: Nov 2004
Location: Lindenhurst, IL
Posts: 659
|
Re: Gap between the rocker and the bedside
mustardjimmy71, bouncytruck, cleszkie and hgs_notes... thank you all. That is exactly the information that I was looking for. Unfortunately for me, that seam on my truck is a gap that I can stick the end of my little finger into. It is what it is, I guess.
Thank you all, again, very much. |
|
|
|
|
03-22-2011, 02:31 AM
|
#7 |
|
toys'r'us
Join Date: Nov 2010
Location: Penticton, BC, Canada
Posts: 347
|
Re: Gap between the rocker and the bedside
i need to take care of mine before it spreads
__________________
71 jimmy bone stock 350 sm465 33x12.5 rallies 79 caprice landau full load crate350 th350 lowered 20"wires 00 f150 reg cab sb 4x4 5.4L |
|
|
|
|
03-27-2011, 12:35 PM
|
#8 |
|
Senior Member
 
Join Date: Mar 2001
Location: From Kansas now in Palmer, Alaska
Posts: 807
|
Re: Gap between the rocker and the bedside
I have owned/parted out about 30 of these blazers. I don't think the original GM assembly line produced a very consistent product....many weren't "perfect" from the factory. My quarter panel stuck out about a 1/4 inch past the edge of the rocker from the factory. I have seen others with big gaps like you are talking about. Are you trying to replace your rocker? I bought a set of repop rockers for my blazer, but ended up scraping them because the fit wasn't very good. I bought a set of NOS ones.....it was like they were actually made for the truck
 John
__________________
63 Buick Wildcat 425 72 Chevy Blazer CST 72 Chevy C10 Cheyenne 00 Ford F-350 Super Duty 7.3L 09 Dodge Challenger SRT-8 10 Ford Expedition Limited |
|
|
|
|
03-27-2011, 11:50 PM
|
#9 |
|
Registered User
Join Date: Nov 2004
Location: Lindenhurst, IL
Posts: 659
|
Re: Gap between the rocker and the bedside
Here's pics of what I'm talking about. The rockers, inner rockers and bedsides have all been replaced. The right side rocker/bedside area is flush, but the left side sticks out about a 1/4".
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
