any ideas for my project? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Norwegian · 04-17-2002, 01:17 PM

Hi, some years ago I inherited this truck. It has bin left rusting in a garage for 10 years before I got it, and now I have started restoring it.

I think it has a 12 bolt positraction rear end and the transmission is a 4 speed on the floor with hi and lo. The engin was an L-6 292, I think, but I have bought a trimmed 350 with about 12:1 compressionratio and 320Hp.

It looks like it fitts well on the old transmission (if I use the old starter), but the pice that the right rubber mounting should fit on to against the frame does not seem fit. Also the rode-linkage from the clutch too the pedal doesn't fit. Is this parts easy to get in the states? And does anyone know if there is more parts I need to replace (for fitting the new engine)?

The information I have says this is a 68 GMC Truck 910, but the part-dealers can't find the model in any of their catalogues. Does anyone know which Chevrolet this truck is similar to? I think the dealers has parts for most Chevrolets.

I don't have a lot of experience in fixing trucks, so my God I was happy when I discovered this board. I have alreaddy learned a lot. Thank you guys.

Here are some pics of it as it was when I got it up here in the north of norway. And the pictures ar not taken at night.

<img src="http://www.tnett.no/oeskara/Image0003.jpg">
<img src="http://www.tnett.no/oeskara/Image0002.jpg">

------------------
Restoring a GMC Truck 910
Have a GMC CCKW 6x6 from 43
Looking for a nice old 4x4 Blazer

NSANE68!!! · 04-17-2002, 01:22 PM

Here ya go. the pics didn't show up.

Nice rig. WELCOME to the board

[This message has been edited by NSANE68!!! (edited April 17, 2002).]

[This message has been edited by NSANE68!!! (edited April 17, 2002).]

**Yukon Jack** · 04-17-2002, 02:03 PM

From your message I wasn't sure if you understood the "hi and lo" is your transfer case. It should actually have a 2 wheel drive Hi and then 4 wheel drive Hi and 4 wheel drive Low range. It should be a Rockwell T221 transfer case and the 4 speed is more than likely the CH465 (sometimes referred to as SM465). The transfer case low range give you a ratio of 1.96 to 1. It is a strong transfer case but parts are hard to find.

Looks like a good starting place. Are you wanting to resto or just make better?

------------------
1969 C20 4x4 with roughly 6" lift and 35's
residing near Rose Hill, Kansas

Yukon Jack's Web Pages

**BIG ORANGE** · 04-17-2002, 03:12 PM

Welcome to the board from S.C.,it sure looks cold where your at in the pic.

------------------
BIG ORANGE 1971 SUBURBAN
1970/90-Little Buck's Truck (ONE DAY)
USED TRUCK PARTS 4 SALE

johnnyp · 04-18-2002, 08:34 AM

Curious about the 910. Anybody have the scoop on this model?

------------------
72 Sierra Grande - "Maych"
sierraG on some boards

If a man speaks in the middle of a forest and there is no woman around to hear him, is he still wrong?

Forget about "do it right the first time". Do it wrong the first time to learn how, then do it right the second time.

Maych Home Page

ARTEMIS · 04-19-2002, 03:09 PM

Couldn't tell you guys about the 910 but for the most part the truck resembles my 69 GMC 3/4 ton longbox stepcide custom pickup

**Yukon Jack** · 04-19-2002, 03:41 PM

If I remember correctly, somebody stated that 910 is the identification used on Canadian trucks, like the C10 identification. Anyone else know?

Norwegian · 04-19-2002, 04:38 PM

That is very likely. The drivers manual saies you have 910, 920 and 930 models.

69 longhorn · 04-19-2002, 04:44 PM

On your motor mounts, the 292 has a different bracket on the RH side,that will need to be changed to bolt the motor. the clutch linkage is all different from 6 to V8,so you will also need those pcs. Good luck...69 longhorn.

Gordo · 04-19-2002, 07:08 PM

Can't help ya much but, The truck is great and the view is better! I know someone here can hook you up with all the parts you need but, shipping could be $$$,,,,and by the way,,,welcome from Killingworth, Connecticut USA!

------------------
1971 C10 swb stepside 350/700R4/3.73posi
Killingworth, Connecticut

04-17-2002, 01:17 PM	#1
Norwegian Registered User Join Date: Mar 2002 Location: Andenes, Norway Posts: 16	any ideas for my project? Hi, some years ago I inherited this truck. It has bin left rusting in a garage for 10 years before I got it, and now I have started restoring it. I think it has a 12 bolt positraction rear end and the transmission is a 4 speed on the floor with hi and lo. The engin was an L-6 292, I think, but I have bought a trimmed 350 with about 12:1 compressionratio and 320Hp. It looks like it fitts well on the old transmission (if I use the old starter), but the pice that the right rubber mounting should fit on to against the frame does not seem fit. Also the rode-linkage from the clutch too the pedal doesn't fit. Is this parts easy to get in the states? And does anyone know if there is more parts I need to replace (for fitting the new engine)? The information I have says this is a 68 GMC Truck 910, but the part-dealers can't find the model in any of their catalogues. Does anyone know which Chevrolet this truck is similar to? I think the dealers has parts for most Chevrolets. I don't have a lot of experience in fixing trucks, so my God I was happy when I discovered this board. I have alreaddy learned a lot. Thank you guys. Here are some pics of it as it was when I got it up here in the north of norway. And the pictures ar not taken at night. <img src="http://www.tnett.no/oeskara/Image0003.jpg"> <img src="http://www.tnett.no/oeskara/Image0002.jpg"> ------------------ Restoring a GMC Truck 910 Have a GMC CCKW 6x6 from 43 Looking for a nice old 4x4 Blazer __________________ 75 Blazer K5 cab 66 Chevrolet Impala 2dht 68 GMC 4x4 pickup (project) 43 GMC CCKW 6x6

04-17-2002, 01:22 PM	#2
NSANE68!!! SLICER AND DICIER Join Date: May 2001 Location: Quuen Creek Posts: 1,383	Here ya go. the pics didn't show up. Nice rig. WELCOME to the board [This message has been edited by NSANE68!!! (edited April 17, 2002).] [This message has been edited by NSANE68!!! (edited April 17, 2002).] __________________ 01 Tahoe 22's 2/4 drop and tv's 68 chevy money pit 51 chevy belair 95 Honda 900RR 05 GMC Siearra (company truck)

04-17-2002, 02:03 PM	#3
Yukon Jack Post Whore Join Date: Feb 2000 Location: Rose Hill, KS, USA Posts: 12,683	From your message I wasn't sure if you understood the "hi and lo" is your transfer case. It should actually have a 2 wheel drive Hi and then 4 wheel drive Hi and 4 wheel drive Low range. It should be a Rockwell T221 transfer case and the 4 speed is more than likely the CH465 (sometimes referred to as SM465). The transfer case low range give you a ratio of 1.96 to 1. It is a strong transfer case but parts are hard to find. Looks like a good starting place. Are you wanting to resto or just make better? ------------------ 1969 C20 4x4 with roughly 6" lift and 35's residing near Rose Hill, Kansas Yukon Jack's Web Pages __________________ 1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14

04-17-2002, 03:12 PM	#4
BIG ORANGE Senior Member Join Date: Oct 2001 Location: Lancaster S.C. Posts: 4,743	Welcome to the board from S.C.,it sure looks cold where your at in the pic. ------------------ BIG ORANGE 1971 SUBURBAN 1970/90-Little Buck's Truck (ONE DAY) USED TRUCK PARTS 4 SALE __________________ Things happen for a reason!

04-18-2002, 08:34 AM	#5
johnnyp Keepin' It Stock Join Date: Aug 2001 Location: Grand Island, Nebraska, USA Posts: 554	Curious about the 910. Anybody have the scoop on this model? ------------------ 72 Sierra Grande - "Maych" sierraG on some boards If a man speaks in the middle of a forest and there is no woman around to hear him, is he still wrong? Forget about "do it right the first time". Do it wrong the first time to learn how, then do it right the second time. Maych Home Page __________________ 72 Sierra Grande - Maych Forget about "do it right the first time". Do it wrong the first time to learn how, then do it right the second time.

04-19-2002, 03:09 PM	#6
ARTEMIS Registered User Join Date: Apr 2002 Location: Mandan, ND Posts: 12	Couldn't tell you guys about the 910 but for the most part the truck resembles my 69 GMC 3/4 ton longbox stepcide custom pickup

04-19-2002, 03:41 PM	#7
Yukon Jack Post Whore Join Date: Feb 2000 Location: Rose Hill, KS, USA Posts: 12,683	If I remember correctly, somebody stated that 910 is the identification used on Canadian trucks, like the C10 identification. Anyone else know? __________________ 1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14

04-19-2002, 04:38 PM	#8
Norwegian Registered User Join Date: Mar 2002 Location: Andenes, Norway Posts: 16	That is very likely. The drivers manual saies you have 910, 920 and 930 models. __________________ 75 Blazer K5 cab 66 Chevrolet Impala 2dht 68 GMC 4x4 pickup (project) 43 GMC CCKW 6x6

04-19-2002, 04:44 PM	#9
69 longhorn Registered User Join Date: Aug 2001 Location: rock island,il,usa Posts: 5,382	On your motor mounts, the 292 has a different bracket on the RH side,that will need to be changed to bolt the motor. the clutch linkage is all different from 6 to V8,so you will also need those pcs. Good luck...69 longhorn. __________________ http://community.webshots.com/user/hotrodhorn

04-19-2002, 07:08 PM	#10
Gordo Registered User Join Date: Jan 2001 Location: Killingworth, CT. USA Posts: 3,378	Can't help ya much but, The truck is great and the view is better! I know someone here can hook you up with all the parts you need but, shipping could be $$$,,,,and by the way,,,welcome from Killingworth, Connecticut USA! ------------------ 1971 C10 swb stepside 350/700R4/3.73posi Killingworth, Connecticut __________________ 1971 C10 swb stepside 350/700R4/3.73posi (retired as of 4/22/03) 1998 S10 short bed 2002 S10 Blazer 1942 Oldsmobile 1958 Massey Harris Pony 1951 Wife Killingworth, Connecticut May those who love us, love us, any of those who do not love us, may God turn their hearts. And if God is unable to turn their hearts, may he turn their ankles so we may know them by their limping. A man who works with his hands is a laborer; a man who works with his hands and his brain is a craftsman; but a man who works with his hands and his brain and his heart is an artist.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.