GMC paul door seals are great!

[lakeroadster]

Originally Posted by GMCPaul

You'll find them only listed on our truck weatherstrip page not on our Blazer or Suburban weatherstrip pages due to the Blazer difference on ends of seals and the Suburbans havea 90 degree corner we've never tried getting these to conform to so we don't list them for them either.
You can go to the page they are on at the following link
http://www.gmcpauls.com/Pickup.htm
Part# 2660241 $49.95 pr & $12.75 shipped priority mail insured anywhere in the USA
Paul @ GMCPauls

Paul,

Are the push on style seals available for 63-66's? I didn't see them online.

Thanks,

John

[GMCPaul]

John AKA lakeroadster I'm sorry but we only currently have these for the 67-72 trucks, I don't own a 60-66 myself so I haven't had a truck I could use to test the various profiles of this push on style door opening weatherstrip on. If there are any 60-66 owners near Rockville that are willing to let me use there truck to develop this same weatherstrip for the 60-66 series I'd be more than willing to give a free set of push on door weatherstrip to them once I was able to determine the best profile seal to have them made from that worked to seal out the elements while not causing any problems closing the doors.
Paul @ GMCPauls

[chewychevy67]

Are the push on style seals available for 63-66's? I didn't see them online.


I used these on my 64 gmc truck and they fit nice on mine.

[lakeroadster]

Originally Posted by chewychevy67

Are the push on style seals available for 63-66's? I didn't see them online.


I used these on my 64 gmc truck and they fit nice on mine.

Sweet! To clarify, are you saying you used the 67-72 push on seals on your 64?

[chewychevy67]

yes i used these on my 67 and my 64. they are a hare tight on the 64 but should break in just fine. better than anything else ive tried and i aint using the glue on's ever again. there just a mess.

[lakeroadster]

Originally Posted by chewychevy67

yes i used these on my 67 and my 64. they are a hare tight on the 64 but should break in just fine. better than anything else ive tried and i aint using the glue on's ever again. there just a mess.

I here ya. I had one helluva time getting the glued on ones off my '65. I will be needing to replace them so I'll be following your lead on this.

So the doors close ok and seal up good with the 67-72 push-on seals?

John

[GMCPaul]

Originally Posted by lakeroadster

Paul,

Are the push on style seals available for 63-66's? I didn't see them online.

Thanks,

John

John AKA-lakeroadster I have some new door seals arriving in about 2 weeks I'd like you to test fit for me on your 66 and give me a review so if you could please email me your address as soon as they arrive I'll ship them to you. Email me at
robbinspd1199@yahoo.com

litew8 If you read the description of the cab rubber kit on our web site page it tells you every part that is included in the kit. If you do not see it in the description then its not included.
the following is that list
Includes
standard 8 piece door window seal kit,
vent window rubber kit,
door opening weather strip kit,
windshield gasket ( Deluxe or Standard),
Rear window gasket ( Deluxe or Standard) Specify Standard or Deluxe in Cart for 67-72 Large back window, 67 Small back window kit comes as standard or deluxe windshield gasket and standard rear window gasket specify in cart. You can optionally upgrade the door opening weatherstrip in the cart from our original style glue on version to our new and improved modern style that pushes on and requires no glue to install. Every Piece in this entire kit is backed with a lifetime warranty.
You'll find the cab rubber kit at this link
http://www.gmcpauls.com/Pickup.htm
Its the 1st item listed on that page.
Where as if you only want the Push-On door seals they are on the same page and are the 9th item listed on that page.
GMCPaul

[litew8]

Thank you for the reply. I no longer need the door seals, so a kit isn't going to work.

I have a "Custom Deluxe", here's what I'm looking at now:

8 Piece Door Window Seal Kit For Custom & CST Trucks 280037
Includes inner felts with Chrome Bead, outer rubber seal, Division Bar Felt,&Door Glass Channel Run For Both Doors Used On CST & Custom Pickup, Suburban & Panel. LIFETIME WARRANTY.
$69.95

67-72 Division Bar Felt 360342
1967-72 Door division bar felt runs down back side of vent window bar from top at door upper frame to bottom inside door. For truck, Blazer, Jimmy, Suburban, Panel.
$12.00

67-72 Glass Run Channel 360346
1967-72 Door glass run channel, extends from inside door bottom at back of window up the rear glass run area and across top of door upper frame and ends at division bar. For Truck, Suburban & Panel.
$10.95

- Questions -
1) Are all rubber products manufactured by Precision?
2) For the 8 piece above (280037), it says "outer rubber seal", but the 4 piece anti-rattle kit (371090) says "2-outer rubber seals with chrome top bead" is included. Is there a difference for Custom Deluxe models, and why wouldn't the 8 piece kit contain outer rubber seals with "chrome top bead"?

4 Piece Custom & CST Door Window Anti-Rattle Kit 371090
For 1967-72 Truck, Blazer, Jimmy, Suburban&Panel. Includes 2-inner felts with chrome top bead, 2-outer rubber seals with chrome top bead, at bottom of window inside and out, does both doors. LIFETIME WARRANTY.
$39.95

Thanks

[GMCPaul]

Originally Posted by litew8

Thank you for the reply. I no longer need the door seals, so a kit isn't going to work.

I have a "Custom Deluxe", here's what I'm looking at now:

8 Piece Door Window Seal Kit For Custom & CST Trucks 280037
Includes inner felts with Chrome Bead, outer rubber seal, Division Bar Felt,&Door Glass Channel Run For Both Doors Used On CST & Custom Pickup, Suburban & Panel. LIFETIME WARRANTY.
$69.95

67-72 Division Bar Felt 360342
1967-72 Door division bar felt runs down back side of vent window bar from top at door upper frame to bottom inside door. For truck, Blazer, Jimmy, Suburban, Panel.
$12.00

67-72 Glass Run Channel 360346
1967-72 Door glass run channel, extends from inside door bottom at back of window up the rear glass run area and across top of door upper frame and ends at division bar. For Truck, Suburban & Panel.
$10.95

- Questions -
1) Are all rubber products manufactured by Precision?
2) For the 8 piece above (280037), it says "outer rubber seal", but the 4 piece anti-rattle kit (371090) says "2-outer rubber seals with chrome top bead" is included. Is there a difference for Custom Deluxe models, and why wouldn't the 8 piece kit contain outer rubber seals with "chrome top bead"?

4 Piece Custom & CST Door Window Anti-Rattle Kit 371090
For 1967-72 Truck, Blazer, Jimmy, Suburban&Panel. Includes 2-inner felts with chrome top bead, 2-outer rubber seals with chrome top bead, at bottom of window inside and out, does both doors. LIFETIME WARRANTY.
$39.95

Thanks

All the rubber is supplied by Precision in this kit. The part # 280037 do have a chrome top bead attached to the 2-outer rubber scrappers and the 2-inner felts in this kit. Its just not in that description and I'll see about getting it added. The division bar felts do not have chrome beads. The division bar felt was installed at GM assembly plant then they crimped a chrome bead onto the rear edge of the vent window assemblies division bar surrounding metal inside & out. When they did this they often trapped a portion of the division bar felt under the edge of this chrome bead. So when removing the division bar felt to replace it run a razor blade along the edge of the chrome bead on the felt side of it this will cut any felt trapped allowing you to remove the division bar felt liner for replacement.
The part # 280037 includes 2 division bar felts and 2 glass run channels so if you only have the 1 truck there is no need to add the part #'s 360342 division bar felt or Part# 360346 glass run channel.
we use a Part # 371090 + 2- Part # 360342 & 2 part # 360343 to make our Part # 280037 kit.
To be sure your questions get answered quickly about any of our products you can contact us direct by emailing us at
robbinspd1199@yahoo.com
as I don't always see every post here. Thanks for your interest!!
Paul @ GMCPauls

[litew8]

Thank you for taking the time out of your busy schedule to answer a few questions! Really appreciate it! I know about the felt being trapped beneath the chrome on the division bar! I just finished sandblasting mine and noticed how some got trapped in that seam. The blaster cleaned it up good for me. Once I get organized, I'm going to buy from GMC Paul! Thanks again!

Originally Posted by GMCPaul

All the rubber is supplied by Precision in this kit. The part # 280037 do have a chrome top bead attached to the 2-outer rubber scrappers and the 2-inner felts in this kit. Its just not in that description and I'll see about getting it added. The division bar felts do not have chrome beads. The division bar felt was installed at GM assembly plant then they crimped a chrome bead onto the rear edge of the vent window assemblies division bar surrounding metal inside & out. When they did this they often trapped a portion of the division bar felt under the edge of this chrome bead. So when removing the division bar felt to replace it run a razor blade along the edge of the chrome bead on the felt side of it this will cut any felt trapped allowing you to remove the division bar felt liner for replacement.
The part # 280037 includes 2 division bar felts and 2 glass run channels so if you only have the 1 truck there is no need to add the part #'s 360342 division bar felt or Part# 360346 glass run channel.
we use a Part # 371090 + 2- Part # 360342 & 2 part # 360343 to make our Part # 280037 kit.
To be sure your questions get answered quickly about any of our products you can contact us direct by emailing us at
robbinspd1199@yahoo.com
as I don't always see every post here. Thanks for your interest!!
Paul @ GMCPauls

[jtp67-72]

Got mine today--won't install for while but Paul my question is in the sharp corner of upper front --is there a trick to install in that area-no prebend in these so I was just curious---Shipping was super fast and where were these on my last 20 trucks???? lol.....thanx again.......jim