67 door glass question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

LMREESE · 02-20-2014, 11:21 PM

What actually holds the glass in place in the channel it rests in?

**truckster** · 02-20-2014, 11:42 PM

It's felt-impregnated rubber. It's a friction fit.

19Chevy67C10 · 02-21-2014, 12:00 AM

If you are speaking of the lower channel that goes on the window requlator, and is attached to the glass it would be called glass setting tape.

LMREESE · 02-21-2014, 07:40 AM

Thanks. My glass is totally loose which causes it to jump the track. Can someone outline the procedure for installing the tape. I assume you have to remove the glass from the door and I have no idea how to do that.

**special-K** · 02-21-2014, 01:45 PM

It's hard to get to,but you should be able to wedge/duct tape the glass in the up position and lower the mechanism. What we don't know yet is why this happened. Could be that channel is crusty,so replacing would be required. Could be the vertical channels got so worn the window was getting cocked and wedge coming down,so popped out of the track. It could be the little roller isn't rolling freely in it's track,so allowing the window to cock and wedge. Pop the interior panel off and have a look,then see where you have to go from there.

**Grumpy old man** · 02-21-2014, 04:18 PM

The easy repair is to use windshield setting urethane and a caulking gun

remove the door panel

raise the loose window and block it up out of the way using a paint paddle or even folded newspaper

clean off the bottom of the glass and the regulator channel remove any friction tape

simply lay a good bead of urethane into the regulator channel and lower the glass into the bed of urethane and gently roll the window up and let set 24 hours and it will never fall off again

This is a quick easy and permanent repair without removing the glass or regulator and works well for worn channels .

02-20-2014, 11:21 PM	#1
LMREESE Registered User Join Date: Aug 2012 Location: Ringgold GA Posts: 149	67 door glass question What actually holds the glass in place in the channel it rests in? __________________ 67 C10 swb bored out 350 granny 4 speed I come from a long line of moonshiners

02-20-2014, 11:42 PM	#2
truckster Senior Member Join Date: Jan 2001 Location: Orem, Utah Posts: 7,795	Re: 67 door glass question It's felt-impregnated rubber. It's a friction fit.

02-21-2014, 12:00 AM	#3
19Chevy67C10 Registered User Join Date: Sep 2011 Location: At the end of the road! Posts: 282	Re: 67 door glass question If you are speaking of the lower channel that goes on the window requlator, and is attached to the glass it would be called glass setting tape. __________________ Kev's-C-10

02-21-2014, 07:40 AM	#4
LMREESE Registered User Join Date: Aug 2012 Location: Ringgold GA Posts: 149	Re: 67 door glass question Thanks. My glass is totally loose which causes it to jump the track. Can someone outline the procedure for installing the tape. I assume you have to remove the glass from the door and I have no idea how to do that. __________________ 67 C10 swb bored out 350 granny 4 speed I come from a long line of moonshiners

02-21-2014, 01:45 PM	#5
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,863	Re: 67 door glass question It's hard to get to,but you should be able to wedge/duct tape the glass in the up position and lower the mechanism. What we don't know yet is why this happened. Could be that channel is crusty,so replacing would be required. Could be the vertical channels got so worn the window was getting cocked and wedge coming down,so popped out of the track. It could be the little roller isn't rolling freely in it's track,so allowing the window to cock and wedge. Pop the interior panel off and have a look,then see where you have to go from there. __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

02-21-2014, 04:18 PM	#6
Grumpy old man Senior Member Join Date: Dec 2013 Location: Gods country East,Tn Posts: 8,545	Re: 67 door glass question The easy repair is to use windshield setting urethane and a caulking gun remove the door panel raise the loose window and block it up out of the way using a paint paddle or even folded newspaper clean off the bottom of the glass and the regulator channel remove any friction tape simply lay a good bead of urethane into the regulator channel and lower the glass into the bed of urethane and gently roll the window up and let set 24 hours and it will never fall off again This is a quick easy and permanent repair without removing the glass or regulator and works well for worn channels .



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.