The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 08-10-2020, 07:05 PM   #1
skyphix
Registered User
 
Join Date: Sep 2018
Location: Hampden, ME
Posts: 406
Help with Steering Shaft Removal

Hey everyone,
Now that the LS/Trans swap is driveable its time to address some maintenance/repair items on the truck itself. This one has been pretty stubborn. Replacing the lower steering column bearing, I've got the bearing kit here, but can't for the life of me get the steering shaft off of the column

See the arrow below;



Where that arrow points - I removed the pinch bolt, and the bulky section with the rubber seal moves down but the shaft itself doesn't collapse at all and I don't want to hammer on it too hard for fear of tearing the rubber boot. Is this just a case of a stuck shaft where I need to drill out/melt out the plastic pins or am I missing something?

Trying to avoid unhooking at the steering box if I can, just because those bolts are all boogered up and ultimately I want to replace the entire setup, so this is just to get it driving a little better.


Thanks in advance
Eric
__________________
Eric
1980 C10 SWB
2003 Chevy Suburban 2500 LT
skyphix is offline   Reply With Quote
Old 08-11-2020, 12:06 PM   #2
rodstored-72
chevy truck fan
 
rodstored-72's Avatar
 
Join Date: Mar 2005
Location: Gilbert, arizona 85298
Posts: 1,954
Re: Help with Steering Shaft Removal

I can't help, but I am wanting to do the same thing so following along.... thanks!
rodstored-72 is offline   Reply With Quote
Old 08-11-2020, 03:32 PM   #3
JJH Jimmy
Senior Member

 
JJH Jimmy's Avatar
 
Join Date: Jun 2012
Location: Schoolcraft, Michigan
Posts: 921
Re: Help with Steering Shaft Removal

I would first soak the end with a good penetrating oil. Next, disconnect the shaft at the rag joint and get it off the steering box then try to hammer it off using an adjustable wrench around the shaft and striking with a hammer. The shaft is sorta of D shaped and is a really tight fit. When you go to reinstall clean both the intermediate shaft end and the steering column shaft end with some sand cloth and make sure it is positioned properly. Good luck sometimes they are a pain in the butt.
__________________
1972 GMC Jimmy 4x4 LS Swap
1985 Chevy K20
1994 GMC Yukon
2021 GMC 2500HD Duramax AT4

My "It's a Jimmy Thing" Build
http://67-72chevytrucks.com/vboard/s...d.php?t=583528
Budget Build 1985 K20
http://67-72chevytrucks.com/vboard/s...d.php?t=801565
JJH Jimmy is offline   Reply With Quote
Old 08-11-2020, 04:48 PM   #4
skyphix
Registered User
 
Join Date: Sep 2018
Location: Hampden, ME
Posts: 406
Re: Help with Steering Shaft Removal

Quote:
Originally Posted by JJH Jimmy View Post
I would first soak the end with a good penetrating oil. Next, disconnect the shaft at the rag joint and get it off the steering box then try to hammer it off using an adjustable wrench around the shaft and striking with a hammer. The shaft is sorta of D shaped and is a really tight fit. When you go to reinstall clean both the intermediate shaft end and the steering column shaft end with some sand cloth and make sure it is positioned properly. Good luck sometimes they are a pain in the butt.


Thanks very much for the advice! I was really hoping to avoid disconnecting the rag joint end because someone at some point rounded off the pinch bolt, but looks like I'll be getting creative with getting that off.

I guess while I've got it apart the responsible thing would be to replace the rag joint at the same time. Snowball effect
__________________
Eric
1980 C10 SWB
2003 Chevy Suburban 2500 LT
skyphix is offline   Reply With Quote
Old 08-12-2020, 05:10 PM   #5
kwmech
Senior Member
 
Join Date: Mar 2003
Location: Colfax-California
Posts: 8,356
Re: Help with Steering Shaft Removal

Quote:
Originally Posted by skyphix View Post
Thanks very much for the advice! I was really hoping to avoid disconnecting the rag joint end because someone at some point rounded off the pinch bolt, but looks like I'll be getting creative with getting that off.

I guess while I've got it apart the responsible thing would be to replace the rag joint at the same time. Snowball effect
It may look rounded but it requires a 12pt socket
kwmech is offline   Reply With Quote
Old 08-13-2020, 10:20 PM   #6
skyphix
Registered User
 
Join Date: Sep 2018
Location: Hampden, ME
Posts: 406
Re: Help with Steering Shaft Removal

Quote:
Originally Posted by kwmech View Post
It may look rounded but it requires a 12pt socket
You made me go look again and yup - it was so packed with crud it looked rounded. Cleaned it off and it’s just a 12pt. Shouldn’t be too bad then.
__________________
Eric
1980 C10 SWB
2003 Chevy Suburban 2500 LT
skyphix is offline   Reply With Quote
Old 08-16-2020, 07:20 PM   #7
v30crewcab
Registered User
 
v30crewcab's Avatar
 
Join Date: Apr 2012
Location: Chatt Tn
Posts: 957
Re: Help with Steering Shaft Removal

I usually have to smack them with a hammer to get them to slide off once the bolt is completely out.
__________________
88 military v30 crewcab shortbed 5.9 cummins, nv4500, 205
86 k30, 89 diesel burb, 76 gmc pathfinder
71 longbed 5.3 4l80
http://67-72chevytrucks.com/vboard/s...d.php?t=522535
v30crewcab is offline   Reply With Quote
Old 08-17-2020, 11:44 AM   #8
SCOTI
Registered User
 
SCOTI's Avatar
 
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 21,894
Re: Help with Steering Shaft Removal

Quote:
Originally Posted by v30crewcab View Post
I usually have to smack them with a hammer to get them to slide off once the bolt is completely out.
x2. Mine was similar.
__________________
67SWB-B.B.RetroRod
64SWB-Recycle
89CCDually-Driver/Tow Truck
99CCSWB Driver
All Fleetsides
@rattlecankustoms in IG

Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive.
It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar.....

Cubic inches is like Indiana Jones with a cheap pistol.
SCOTI is offline   Reply With Quote
Old 08-17-2020, 04:45 PM   #9
kipps
Registered User
 
Join Date: Jul 2014
Location: North-central Virginia
Posts: 1,099
Re: Help with Steering Shaft Removal

It's been awhile, but from my memory, it comes apart at the steering box a lot easier than at the steering column. I doubt you'll have any trouble. Spray it down with pBlaster overnight, and it should slide right off.
__________________
1987 C6P V20 truck, 2010 LMG 5.3, AFM delete, 2010 Camaro exhaust manifolds, 1997 nv4500, 1991 np241c, hydroboost, 2005 14bff axle & driveshaft, drop-n-lock gooseneck, 4.10 gears, stock suspension, rims, and tires. Still a work in progress. Any questions or suggestions are welcome!
kipps is offline   Reply With Quote
Old 08-18-2020, 09:31 AM   #10
skyphix
Registered User
 
Join Date: Sep 2018
Location: Hampden, ME
Posts: 406
Re: Help with Steering Shaft Removal

Thanks very much guys - hoping to tear into this again at some point this week. Gotta go grab some 12pt sockets and I've been hitting both ends with PB every time I open the hood.
__________________
Eric
1980 C10 SWB
2003 Chevy Suburban 2500 LT
skyphix is offline   Reply With Quote
Old 08-19-2020, 08:53 PM   #11
Pontiac1976
Registered User
 
Pontiac1976's Avatar
 
Join Date: Oct 2015
Location: Ottawa, Ontario, Canada
Posts: 750
Re: Help with Steering Shaft Removal

You will only need a 7/16 12 point socket or 7/16 box end wrench to get it off.
__________________
1977 REG cab Long Bed with a 1984 Front Clip, 82 305 .60 over 9.0.1 flat top pistons, 4bbl, TH350, w/84 SS-intake & cam , w/ 1977 big block rad, 1975 gear box, 1984 master w/ metric fittings top & SAE fitting @ portion block, 1975 3.42 gear open diff. Duel 77-87 Factory air cleaner, duel inlet from rad support . Down sized 9' to new 8' Steel flat bed
Was a 77 454 w/308 gear. Taken out 550 lbs. up front with motor clip change.
Pontiac1976 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:51 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com