|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
09-22-2020, 08:31 AM
|
#1 |
|
F’B’D guy
 
Join Date: Feb 2004
Location: Texas/Maine
Posts: 2,208
|
1987 V10 with SM 465, how many bolts hold the bell hosing to the block ?
I’m pulling the engine on my 87 V10 (4X4) 350TBI engine, it has the manual transmission (SM 465?) and I cannot for the life of me get them separated. I’m thinking maybe I missed a bolt or something ? The truck is 100% original with 120,000 original miles.
Thoughts?  
|
|
|
|
09-22-2020, 09:16 AM
|
#2 |
|
Registered User
Join Date: Nov 2014
Location: Norfolk,NE
Posts: 136
|
Re: 1987 V10 with SM 465, how many bolts hold the bell hosing to the block ?
6 bolts.
The dowel pins in the block usually have a good grip on the bellhousing, especially if they've never been seperated and have some corrosion going on. Lift up and down on the engine a few times and it will work loose. Obviously make sure all the bolts are out.
__________________
1982 Sierra Classic K15 RC/LB 6.2L Diesel 700R4 1988 GTA Trans AM 305 TPI 700R4 1993 Formula Firebird LT1 T56 1995 GMC K2500 ECLB 6.5L 4L80E 1996 GMC K3500 CCLB LB7 6L90 |
|
|
|
|
09-22-2020, 09:33 AM
|
#3 |
|
F’B’D guy
Join Date: Feb 2004
Location: Texas/Maine
Posts: 2,208
|
Re: 1987 V10 with SM 465, how many bolts hold the bell hosing to the block ?
 Thanks ! got 6 out, dowel pins are finally separated but it not coming apart anymore., I may have it in a bind or the transmission shaft is rusted where it goes into the clutch maybe ? Never had one split apart so hard.... |
|
|
|
|
09-22-2020, 08:55 PM
|
#4 |
|
F’B’D guy
Join Date: Feb 2004
Location: Texas/Maine
Posts: 2,208
|
Re: 1987 V10 with SM 465, how many bolts hold the bell hosing to the block ?
Note to self; Removal of exhaust manifolds and accompanying emission crap is necessary for engine removal
|
|
|
|
|
09-22-2020, 09:02 PM
|
#5 |
|
Senior Member
Join Date: Mar 2003
Location: Colfax-California
Posts: 8,387
|
Re: 1987 V10 with SM 465, how many bolts hold the bell hosing to the block ?
Hmm, really. I've pulled out big blocks without removing all that. I think the pilot was stuck
|
|
|
|
|
09-23-2020, 06:14 AM
|
#6 | |
|
F’B’D guy
Join Date: Feb 2004
Location: Texas/Maine
Posts: 2,208
|
Re: 1987 V10 with SM 465, how many bolts hold the bell hosing to the block ?
Very well could have been the case....
Quote:
|
|
|
|
|
|
09-23-2020, 02:04 PM
|
#7 |
|
Registered User
Join Date: Apr 2012
Location: Chatt Tn
Posts: 957
|
Re: 1987 V10 with SM 465, how many bolts hold the bell hosing to the block ?
theres no metal rod coming from the motor mounts to the trans on a stick is there? the th400 ones had them.
__________________
88 military v30 crewcab shortbed 5.9 cummins, nv4500, 205 86 k30, 89 diesel burb, 76 gmc pathfinder 71 longbed 5.3 4l80 http://67-72chevytrucks.com/vboard/s...d.php?t=522535 |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
