The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board > 67-72 Chevrolet & GMC Pickups Projects and Builds

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 01-09-2017, 01:32 PM   #1
Snake72
Registered User
 
Snake72's Avatar
 
Join Date: Jan 2017
Location: Iowa
Posts: 239
Grandpa's 72 restoration

Hey All, new guy here with a good story about a cool truck. I've been lurking on this site for the last year and it's amazing the amount of knowledge that is available here! Thanks guys! I'm trying to make progress with this truck, I have a 3 year old and twins due in June '17 so my "fun" time will be coming to an end for awhile. Now, about the truck. I'll try to keep it short

My grandpa bought this 72 custom deluxe new in 1972. My dad rode with him home from the dealership in it. Grandpa passed away in '76, I never had a chance to meet him. Grandma kept it on the farm here in Iowa and kept it in fantastic original condition. She let my uncle use it as his farm truck when he got out of the marines about 1993 and started the farm back up. Farm use took its toll on old blue and its 350 eventually gave out and was parked back at my grandmas indoors for the last 5 years. I learned how to drive in this truck, in the middle of a picked bean field. Always wanted it. Grandma said it was mine whenever I was ready. Last year my father in law retired and bought himself a shop. He used to own a body shop and race dirt track/build motors. We picked up old blue September '15 and started tearing into it. The truck was far worse than what it looks like in pictures, all sheet metal below the trim is rusted through, rockers and cab corners non existent, floor and cab supports gone. But the truck is 100% original except long lost hub caps. I really wanted to LS swap, cut down to short bed and slam it but just cant do it. Too complete and original motor, trans, everything! So its getting restored back to factory. Enough talking, everyone just wants pics. Here is first few pics
Attached Images
    
Snake72 is offline   Reply With Quote
Old 01-09-2017, 01:35 PM   #2
Deer_hunter_088
Registered User
 
Deer_hunter_088's Avatar
 
Join Date: Aug 2016
Location: Mount Carmel Illinois
Posts: 1,321
Re: Grandpa's 72 restoration

In for this one!!!
__________________
1994 k1500, Oldredz71(ext shorty 4x4 6 in lift)
1998 S10ZR2
2005 Silverado 2500hd(tow pig)


Made in the USA, just like my trucks
Deer_hunter_088 is offline   Reply With Quote
Old 01-09-2017, 04:33 PM   #3
Snake72
Registered User
 
Snake72's Avatar
 
Join Date: Jan 2017
Location: Iowa
Posts: 239
Re: Grandpa's 72 restoration

Here are a few more pics. Decided to replace whole floor (awesome replacement piece by the way!!) both cab corners, rockers, A and B posts, kick panels, doors reskinned and bottoms replaced. 350 is going to look stock but bored and stroked to 383. Trying to stay with quadrajet and ram horns for factory look.
Attached Images
     
Snake72 is offline   Reply With Quote
Old 01-09-2017, 04:52 PM   #4
Snake72
Registered User
 
Snake72's Avatar
 
Join Date: Jan 2017
Location: Iowa
Posts: 239
Re: Grandpa's 72 restoration

And finally to bring the project up to current, we repainted the cab medium blue and white. I think it came out well for my first paint job. The floor was coated in raptor liner top and bottom, highly recommend this product. Should never have a rusty floor again!

The metal repair was slow and tedious but nothing was too difficult. The only fitment issue was the trans tunnel on new floor not quite meeting up with firewall but the metal can be worked enough to fit well.

The blue and white truck in the background is my father in laws '71 Cheyenne, very nice original truck with great patina. It's next on the chopping block
Attached Images
     
Snake72 is offline   Reply With Quote
Old 01-10-2017, 10:46 AM   #5
Snake72
Registered User
 
Snake72's Avatar
 
Join Date: Jan 2017
Location: Iowa
Posts: 239
Re: Grandpa's 72 restoration

I need some opinions from you guys.

1) keep factory pinstripe? I have the original option list, it was a $13 option haha. I don't really like it though. Add stainless upper belt trim? or leave no trim/pinstripe?

2)White bumpers? Most go with chrome obviously, original front is in very good condition, I found a painted white rear sport bumper on CL and had it blasted and painted, looks brand new. So, who likes chrome? Who likes white?

3) Wheels? Original white steelies vs rallies I bought cheap and repainted vs old school slot or cragar ss

I go back and forth between all these, help me make a decision!
Snake72 is offline   Reply With Quote
Old 01-10-2017, 10:48 AM   #6
68Gold/white
Registered User
 
Join Date: Sep 2011
Location: Ark City, Kansas
Posts: 3,265
Re: Grandpa's 72 restoration

Way Cool!
Who made the floor panel?
What part of Iowa are you in?
68Gold/white is offline   Reply With Quote
Old 01-10-2017, 10:53 AM   #7
Snake72
Registered User
 
Snake72's Avatar
 
Join Date: Jan 2017
Location: Iowa
Posts: 239
Re: Grandpa's 72 restoration

Thanks 68!

Floor pan was a Triplus, bought from GMC Pauls if I remember right. $500 shipped but worth every penny.

Im in eastern Iowa, near Iowa City. Truck is 2 hours away in northern Iowa at my FIL's shop, he tinkers with it when he can and I get up there about once a month for the weekend. Thus the slow process. Now that deer season is over, my weekends are a little more open
Snake72 is offline   Reply With Quote
Old 01-10-2017, 01:00 PM   #8
sduckworth13
Registered User
 
sduckworth13's Avatar
 
Join Date: Mar 2011
Location: Kansas City, Missouri
Posts: 3,541
Re: Grandpa's 72 restoration

Awesome job on the truck so far.
__________________
Scott
sduckworth13 is offline   Reply With Quote
Old 01-10-2017, 08:45 PM   #9
Elliot949
Dan Johnston
 
Elliot949's Avatar
 
Join Date: Sep 2010
Location: Winfield, Ks.
Posts: 4,162
Re: Grandpa's 72 restoration

Dud.. THat is looking GREAT... congratulations...
__________________
Dan Johnston... Owner of My Dad's- '67 Chevy C-20 Custom Camper Short Fleetside Pickup PAPA J And our newest addition a- '71 Chevy CST/10 Short Fleetside Pickup Haulin' SOLD
Papa J's Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=612847

Haulin's Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=671130SOLD

B Bears Build Thread:http://67-72chevytrucks.com/vboard/s...d.php?t=744210
Elliot949 is offline   Reply With Quote
Old 01-10-2017, 10:26 PM   #10
1972CheyenneSuper
Registered User
 
1972CheyenneSuper's Avatar
 
Join Date: Feb 2006
Location: ND
Posts: 201
Re: Grandpa's 72 restoration

Nice project and cool heritage. My cab is in a similar situation to how yours was. I see you cut the cab corners and bottom of the a and b pillars off while the floor was also off. Did you patch the new pieces in before putting the floor in, or do them after? I'm trying to figure out the best order to tackle mine, but I want to make sure I get everything lined up properly. I'm thinking about doing the pillars first so I don't loose any reference measurements and then dropping the old floor out and new one in. Any suggestions would be helpful.
1972CheyenneSuper is offline   Reply With Quote
Old 01-11-2017, 10:48 AM   #11
Snake72
Registered User
 
Snake72's Avatar
 
Join Date: Jan 2017
Location: Iowa
Posts: 239
Re: Grandpa's 72 restoration

1972CheyenneSuper, I'd be glad to show you how we did it. I should have taken more pics of the install to document our process. I'm sure there are several different ways to install this, probably all depending on the starting point of your cab and metal. My cab, although it looks pretty clean in pictures, was horrible. A and B pillars nearly gone, no driver side rocker and passenger rocker was metal tape covering holes. The cab corners were metal tape and a field stone spray foamed to cover a hole. No joke. Old grandma did her own body work on this truck which consisted of rough bondo, metal tape, and blue paint brushed on over rust. She did her best haha. So we had little to use as original reference. We cut out all the cancer just to see what we were working with. We also had a rotisserie, made things much MUCH easier but not necessary. I read and re-read every thread on this site about floor replacements and was a huge help.
1) brace inside of cab, we used tubing to span door frame, hinge bolt to striker area. Then welded cross pieces from back of cab to firewall and diagonals. You don't want a flimsy cab or torqued/misaligned cab when trying to fit new floor
2) we then cut out cab corners, rockers, A, B pillars just to see where all the seams were.
3) used a spot weld hole saw (get one) and worked over the back of the cab to cut out all the spot welds holding the floor to cab. Half the driver side welds were already broken...nothing even holding the floor up on driver side. Seat belt bolts were ripped out by hand....
4) once rear of floor is free, we used a sawzall and cut front of floor about 1-2" from firewall flange and pulled the floor out.
5) Spot welds were then cut on front flange and used an air hammer to peel back that 1-2" left over flange.
6) Fit new piece, call some buddies over to help, not a 1 or 2 person job. Use lots of vice grips to hold and get it fitted right. Trans tunnel and areas by the A pillars may take some convincing.
7) Make sure front and rear seams are fitting well, we used 2 bolts to temporarily connect the rear cab and floor while welding the front floor to firewall
8) Plug weld floor in, using holes were old spot welds were drilled out on firewall flange and back of cab. We even drilled some new holes for extra welding.
9) We worked from A pillars in to trans tunnel and made adjustments to tunnel fitting
10)plug weld the back of cab. Easiest part.

After floor was welded in we started fitting A and B pillars. A pillars get bolted to floor and only one way they can go in, not much adjusting. B pillars were easy, just take your time and fit as good as you can.

The cab corners also lined up perfectly, however I had so much rust in mine that we used the entire replacement panel on both sides. We had to cut out a lot of metal from cab.

Im probably missing some info but its really not bad. This is my first ever project and my FIL had never done anything this in depth but we worked through it without issue. Just take your time and think it through. Literally all the metal from the trim line down is new in this truck, we had zero reference to go off of and the doors fit better than new. Good luck!!
Attached Images
     
Snake72 is offline   Reply With Quote
Old 01-11-2017, 10:58 AM   #12
Snake72
Registered User
 
Snake72's Avatar
 
Join Date: Jan 2017
Location: Iowa
Posts: 239
Re: Grandpa's 72 restoration

Also, when the old floor is cut out, clean up the firewall flange and back of cab flange to bare metal, get all rust out. Spray flange with good weld through primer to help prevent any rust starting in new floor/flange seam. Then seam seal flange when you're done.
Attached Images
     
Snake72 is offline   Reply With Quote
Old 01-11-2017, 11:14 AM   #13
Snake72
Registered User
 
Snake72's Avatar
 
Join Date: Jan 2017
Location: Iowa
Posts: 239
Re: Grandpa's 72 restoration

This is what a cab corner and floor supports should look like from underneath!! Again, I highly recommend raptor liner over the new floor. $120 gets you enough material and the gun to spray floor and inside wheel wells and rear tubs. Dries to very tough hard plastic type feel. Stinks like a hog lot on a 105 degree day though. Strong chemicals. Wear a respirator and open doors or your wife will find you running around naked in the garage thinking the CIA is coming for you
Attached Images
  
Snake72 is offline   Reply With Quote
Old 01-11-2017, 11:34 AM   #14
sduckworth13
Registered User
 
sduckworth13's Avatar
 
Join Date: Mar 2011
Location: Kansas City, Missouri
Posts: 3,541
Re: Grandpa's 72 restoration

"Stinks like a hog lot on a 105 degree day though. Strong chemicals. Wear a respirator and open doors or your wife will find you running around naked in the garage thinking the CIA is coming for you."

Lol.. reminds me of those kids in high school sniffing varnish in the back of the wood class shop.
__________________
Scott
sduckworth13 is offline   Reply With Quote
Old 01-11-2017, 08:59 PM   #15
1972CheyenneSuper
Registered User
 
1972CheyenneSuper's Avatar
 
Join Date: Feb 2006
Location: ND
Posts: 201
Re: Grandpa's 72 restoration

Very good info! Thank you for taking the time to write that, it should help me put everything into a little better perspective.
1972CheyenneSuper is offline   Reply With Quote
Old 01-11-2017, 09:41 PM   #16
72 tigger
Senior Member
 
72 tigger's Avatar
 
Join Date: Apr 2008
Location: Berne IN
Posts: 3,188
Re: Grandpa's 72 restoration

I think 15x8 (same width as rallies) steel wheels & painted caps- think thats what it had from the factory- would look great. You're doing a great job! Keep it up
72 tigger is offline   Reply With Quote
Old 01-12-2017, 11:08 AM   #17
jimbosprint
Registered User
 
jimbosprint's Avatar
 
Join Date: Jul 2014
Location: Chico, California
Posts: 940
Re: Grandpa's 72 restoration

Quote:
Originally Posted by Snake72 View Post
I need some opinions from you guys.

1) keep factory pinstripe? I have the original option list, it was a $13 option haha. I don't really like it though. Add stainless upper belt trim? or leave no trim/pinstripe?

2)White bumpers? Most go with chrome obviously, original front is in very good condition, I found a painted white rear sport bumper on CL and had it blasted and painted, looks brand new. So, who likes chrome? Who likes white?

3) Wheels? Original white steelies vs rallies I bought cheap and repainted vs old school slot or cragar ss

I go back and forth between all these, help me make a decision!
Very nice work!

Based on the work you are putting in, and since you aren't going custom on the engine, I would put it back as original as possible. Pinstripe, white bumper, stock wheels/caps.

I sure wish I could find a straight patina white front bumper for my truck...
jimbosprint is offline   Reply With Quote
Old 01-12-2017, 11:22 AM   #18
MMcMasters
Registered User
 
MMcMasters's Avatar
 
Join Date: Dec 2012
Location: Rochester, IL
Posts: 537
Re: Grandpa's 72 restoration

Excellent metalwork, this is going to be a very nice piece when you are done!
__________________
__________________
Mike



70 Med Olive build http://67-72chevytrucks.com/vboard/s...d.php?t=714804

Instagram- protouring66
MMcMasters is offline   Reply With Quote
Old 01-13-2017, 11:21 AM   #19
Snake72
Registered User
 
Snake72's Avatar
 
Join Date: Jan 2017
Location: Iowa
Posts: 239
Re: Grandpa's 72 restoration

Thanks for all the compliments. Hopefully this thread shows that even a novice can tackle rust! Having a FIL with a nice shop and fancy tools sure helps too

Keep the opinions coming on which direction to go with wheels/bumpers/etc. It will more than likely be white steelies with the chrome hubcaps and AT tires of some type to keep the "farm look". The factory paint stripe must be fairly rare, I have not seen many examples of it. If anyone has a factory stripe truck, post pics! It's also a leaf spring truck, wish it was coil, but it will remain leaf spring. So far the only changes from stock is a houndstooth seat cover, rear sport bumper instead of the ugly farm bumper, and carpet for a little more comfort. Was the rubber mat originally. And the old 350 will have a little more grunt

Jimbo, here is the original front bumper after some compound and scuff pad to clean it up. Will probably still repaint.

Here's the original grill. I hammered out a few small dents, hit it the easy off oven cleaner treatment to remove anodizing, and spent about 20 hours sanding and polishing. Came out great but very time consuming.

Also rebuild door hinges. Those old hinge pins are not fun to get out. But hinges are tight now! Should make hanging the door and setting gaps easier.

Last pic is my dads '56 Chevy bought new by his grandpa, my great grandpa. That pic was taken in the early 60's on the same farm the '72 spent its life on. The '56 is also completely original, 235 six with 3 on tree. I learned to drive a manual in this truck, even drove it to high school occasionally way back when. It needs a full resto as well. Iowa winters are not kind to vehicles.
Attached Images
     
Snake72 is offline   Reply With Quote
Old 01-13-2017, 12:29 PM   #20
72 tigger
Senior Member
 
72 tigger's Avatar
 
Join Date: Apr 2008
Location: Berne IN
Posts: 3,188
Re: Grandpa's 72 restoration

Grill looks great! The 56 is cool- neat that its been in the family for 60+ years
72 tigger is offline   Reply With Quote
Old 01-13-2017, 02:22 PM   #21
cericd
Senior Member
 
cericd's Avatar
 
Join Date: Jan 2012
Location: Texan, back in TX
Posts: 2,082
Re: Grandpa's 72 restoration

I applaud you for not chopping it down to a shorty and going with a factory style restoration. It's looking great so far and I look forward to seeing it progress. Great job!

My opinion on the options you mentioned are:

1) Keep the factory pinstripe. You don't see them much. I think they are pretty cool especially since it's actually on your SPID. I included a pick of a factory stripe truck as an example.

2) White bumpers? Keep 'em. Looks great on a blue and white truck. My truck originally had white bumpers but the previous owner put on a chrome front because he didn't like the white accents. I would go back with white but I've found several examples of my color truck (gold) with white bumpers and didn't care for the look. However, if my truck were blue, hugger orange, red, or almost any other color, I'd go with white.

3) Wheels? No question, white wheels with factory caps. White or stainless, your choice. Either will look great.
Attached Images
   
__________________
Chris

My 1970 SWB C/10 - https://67-72chevytrucks.com/vboard/...d.php?t=534872

Last edited by cericd; 01-13-2017 at 02:45 PM.
cericd is offline   Reply With Quote
Old 01-13-2017, 02:50 PM   #22
Snake72
Registered User
 
Snake72's Avatar
 
Join Date: Jan 2017
Location: Iowa
Posts: 239
Re: Grandpa's 72 restoration

Thank you, I though long and hard about cutting it down, even bought a 5.3 and 4l60e before deciding to keep original 350. Now I have an LS to get rid of. Actually bought a complete Texas c30 cab and front clip too. So glad we kept the original cab, would have been a big mistake and regretted swapping cabs and motors.
Snake72 is offline   Reply With Quote
Old 01-13-2017, 02:55 PM   #23
Snake72
Registered User
 
Snake72's Avatar
 
Join Date: Jan 2017
Location: Iowa
Posts: 239
Re: Grandpa's 72 restoration

Awesome pics, exactly where I'm headed. Leaning towards chrome caps, the truck initially had white. The bottom pic is nearly identical to my truck, even has the pin stripe. Thank you for your opinions, there are so many ways to make these trucks look sick but this unmolested example deserves to be the way it rolled off the line.
Snake72 is offline   Reply With Quote
Old 01-14-2017, 09:09 AM   #24
GR8-68
Senior Member
 
GR8-68's Avatar
 
Join Date: Jun 2009
Location: Belews Creek , NC
Posts: 4,220
Re: Grandpa's 72 restoration

This is an awesome story and a cool build, in for the ride on this one
Is that raptor stuff a bed liner material ?
__________________
Larry

It is easily overlooked that what is now called vintage was once brand new.

"Project 68"

paypal.me/ldgrant
GR8-68 is offline   Reply With Quote
Old 01-14-2017, 11:51 AM   #25
Snake72
Registered User
 
Snake72's Avatar
 
Join Date: Jan 2017
Location: Iowa
Posts: 239
Re: Grandpa's 72 restoration

Yup, raptor liner is a spray on bedliner, made by UPOL. Google search it, people use it for all sorts of stuff. I bought mine through amazon, kit came with a gun. Mix activator with product, attach canister to spray gun and air and have at it. As with anything, prep is key. Covers very well, feels like line-x
Snake72 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 04:39 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com