![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Senior Member
![]() Join Date: Feb 2009
Location: Helena, Montana
Posts: 553
|
Inner windshield header piece
Does anyone have experience with reproduction inner header piece for the front windshield frame? Mine is rusted but the upper header is all solid
|
![]() |
![]() |
![]() |
#2 |
Senior Member
![]() Join Date: May 2011
Location: Greencastle PA
Posts: 6,716
|
Re: Inner windshield header piece
There is a good write up on the board on the repoped headers, I'll see if I can find it.
|
![]() |
![]() |
![]() |
#3 |
Senior Member
![]() Join Date: May 2011
Location: Greencastle PA
Posts: 6,716
|
Re: Inner windshield header piece
Keep in mind, this was 6 years ago so I would assume they have fixed some of the issues
http://67-72chevytrucks.com/vboard/s...ght=windshield |
![]() |
![]() |
![]() |
#4 | |
Senior Member
![]() Join Date: Feb 2009
Location: Helena, Montana
Posts: 553
|
Re: Inner windshield header piece
Quote:
|
|
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: May 2021
Location: Center Barnstead NH
Posts: 34
|
Re: Inner windshield header piece
I did the complete windshield header 5pc. kit recently and it fit very good, the only problem i had was the screw holes for the visor retainers were too big. i didnt even have to do any trimming to the 3 outer pieces. just a little on the 2 inner braces.
__________________
1972 C10 SWB 383 M22 1972 K20 454 1970 K5 1985 M1008 1986 M1008 2020 2500HD Duramax |
![]() |
![]() |
![]() |
#6 |
Senior Member
![]() Join Date: Feb 2009
Location: Helena, Montana
Posts: 553
|
Re: Inner windshield header piece
Do you know what brand the parts were and where did you source them?
|
![]() |
![]() |
![]() |
#7 |
Senior Member
Join Date: Jun 2007
Location: Pine Ridge Florida
Posts: 4,121
|
Re: Inner windshield header piece
I believe the windshield header pieces are only made by one manufacturer. I Purchased the pieces a little while ago and they are not installed yet. When I was looking to purchase everybody was out of stock. And then everybody seem to have them about the same time when they came back?
__________________
Click on my Not really a build thread, yet NOT SO RUST FREE RUST FREE BLAZER LS ENGINE SWAP INFORMATION THREAD BOLT RESTORATIONS 4l60 to an NP205 |
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: May 2021
Location: Center Barnstead NH
Posts: 34
|
Re: Inner windshield header piece
I got them from GMC Paul's
__________________
1972 C10 SWB 383 M22 1972 K20 454 1970 K5 1985 M1008 1986 M1008 2020 2500HD Duramax |
![]() |
![]() |
![]() |
#9 |
Senior Member
![]() Join Date: Nov 2014
Location: Colorado
Posts: 3,164
|
Re: Inner windshield header piece
I purchased one a year or two ago. Manufactured by Woodall. Very nice piece. Something to consider is that all you need is the inner piece. Just buy the inner piece for a truck, drill and weld in the captured visor nuts. Done.
__________________
07' Extcab Silverado Z71 Silver Birch, 5.3L HO 71' Cheyenne C10 Hugger Orange on Saddle SWB Besides these two, too Many to count |
![]() |
![]() |
![]() |
#10 |
Senior Member
![]() Join Date: Feb 2009
Location: Helena, Montana
Posts: 553
|
Re: Inner windshield header piece
I wish it was that easy. Blazer header panel is significantly different than pickup
|
![]() |
![]() |
![]() |
Bookmarks |
|
|