The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 08-27-2011, 04:13 PM   #1
srvivor71
Registered User
 
srvivor71's Avatar
 
Join Date: Sep 2010
Location: Sullivan County, NY
Posts: 455
Steering Wheel Installation

Does any one know what the proper torque for the steering wheel nut is supposed to be? I had my wheel off and since I put it back on, it has been binding up when I drive - instead of returning itself to center, it gets hung up and I have to force it to return to center. I'm thinking I may have overtorqued it and got to wondering what the spec is for this. I haven't been able to find it with a google search.

Also, is the steering column shaft supposed to be able to travel up and down along its length by about 1". That's what mine did. Is that normal?

Any advice appreciated...
srvivor71 is offline   Reply With Quote
Old 08-27-2011, 04:19 PM   #2
sethv
Registered User
 
sethv's Avatar
 
Join Date: May 2011
Location: Bradford, PA
Posts: 395
Re: Steering Wheel Installation

I'm not too sure of the torque spec, but I always tightened it up snug and then tightened it a quarter more. Its been working flawlessly for me since I put my Grant wheel on 2 months ago.
__________________
1981 K10 Scottsdale
305 ci | TH350 | NP208 |
60k miles
sethv is offline   Reply With Quote
Old 08-27-2011, 04:30 PM   #3
Stocker
20' Daredevil (Ret)
 
Stocker's Avatar
 
Join Date: May 2003
Location: Jefferson State
Posts: 13,488
Re: Steering Wheel Installation

I tightened mine the same way sethv did. I didn't think tightening the steering wheel nut had any effect on the wheel returning to center. The only time I experienced centering problems was when monkeying with the adjustment screw on a worn-out steering box.

Your 1" of lengthwise play sounds excessive but I don't know what might cause it. Mine has very little free play.

Sorry I wasn't more help.....
__________________
- Mike -

1972 K20 LWB 350/350/205

RIP El Jay
Stocker is offline   Reply With Quote
Old 08-27-2011, 09:16 PM   #4
hugger6933
Registered User
 
Join Date: Oct 2008
Location: Marianna Arkansas
Posts: 7,257
Re: Steering Wheel Installation

sounds like the upper bearing popped up and that is causing the slack. How far into the coloum did you go? I have noticed the upper bearing coming loose with the wheel off before on other models but there should have been a lock ring IIRC to keep that from happining but it may have come loose
hugger6933 is offline   Reply With Quote
Old 08-27-2011, 09:25 PM   #5
ChevLoRay
Old Skool Club
 
ChevLoRay's Avatar
 
Join Date: Jun 2001
Location: Benton, AR "The Heart of Arkansas"
Posts: 10,880
Re: Steering Wheel Installation

I never torqued 'em. I just put the wheel adapter back on and tightened up everything that either held the adapter to the column, or the wheel to the adapter. If I was able to drive it and the steering wheel stayed where I put it and the vehicle when where it was pointed....I was happy.
__________________
Member Nr. 2770

'96 GMC Sportside; 4.3/SLT - Daily driven....constantly needs washed.

'69 C-10 SWB; 350/TH400 - in limbo

The older I get, the better I was.
ChevLoRay is offline   Reply With Quote
Old 08-28-2011, 12:40 PM   #6
srvivor71
Registered User
 
srvivor71's Avatar
 
Join Date: Sep 2010
Location: Sullivan County, NY
Posts: 455
Re: Steering Wheel Installation

Quote:
Originally Posted by hugger6933 View Post
sounds like the upper bearing popped up and that is causing the slack. How far into the coloum did you go? I have noticed the upper bearing coming loose with the wheel off before on other models but there should have been a lock ring IIRC to keep that from happining but it may have come loose
It went down about an inch. I took the top bearing and its carrier out to clean, inspect and grease because something was grinding when I turned the wheel. When I put it back together the shaft had slid down the column so I pulled it back up. Now that it's all back together the wheel is binding.
Posted via Mobile Device
srvivor71 is offline   Reply With Quote
Old 08-28-2011, 12:56 PM   #7
wilbilt
Registered User
 
wilbilt's Avatar
 
Join Date: Aug 2011
Location: Northern California
Posts: 189
Re: Steering Wheel Installation

The steering shaft end play can be adjusted with the rotating collar at the lower end of the column that houses the lower bearing.

The torque spec for the steering wheel nut is 40 ft. lbs.
__________________
1971 GMC C2500 Custom Camper - Second Owner.
350/TH350, Dana 60 Rear.
wilbilt is offline   Reply With Quote
Old 08-28-2011, 04:41 PM   #8
srvivor71
Registered User
 
srvivor71's Avatar
 
Join Date: Sep 2010
Location: Sullivan County, NY
Posts: 455
Re: Steering Wheel Installation

Perfect! Thanks Wilbilt. And thanks to everyone else too.
srvivor71 is offline   Reply With Quote
Reply

Bookmarks

Tags
steering column, steering wheel, steering wheel nut, torque

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:59 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com