The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current Classic GM Trucks Classifieds > The 1967-1972 Chevrolet & GMC Pickups Parts Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 09-20-2020, 02:51 PM   #1
clay68c10
Senior Member
 
clay68c10's Avatar
 
Join Date: Aug 2004
Location: Centennial, CO
Posts: 2,881
Tilt column "truck clone"

$475 local for now. I may ship later if I can find good thick-wall tube.

Please respond in thread only per board rules, first "I'll take it" gets it.

Selling a painted and converted motorhome tilt column. From a mid 80s GM chassis

It has the straight shifter arm like a truck tilt

Also has the metal gear indicator and L1/L2 script lens like a truck tilt

I moved the NSS down so it's a bolt-in for your 67-72; I used my multi-meter to adjust it, you may need to fine tune it after install.

Turn signal and tilt levers are new from GMC Pauls

New GMC Paul's gear indicator

Turn signal switch is new

Good used cancel cam

The gray illumination wire is long

Includes a long pigtail for the Neutral Safety/Reverse switch

Tilt mechanism is tight and smooth.

The 4 bolts in the tilt mechanism that typically loosen over time have been removed and reinstalled with lock-tight.

Tilt pivots were cleaned and lubed when removed to tighten the bolts.

The bottom bearing was cleaned and greased

The upper bearings were cleaned and greased

The shift indicator bulb was replaced and tested OK, it has the green shade on it.

Shifter lever end (inside column) is good, pivot is good

Shift arm has nice chrome, it shines up well. There are 2 small ding spots, shown in the pics

The finish on it is base/clear coat gloss black.

The shift arm is metallic silver and includes the rubber bushing and metal sleeve

New firewall and dash gaskets from GMC Pauls

Firewall mount plate included, blasted and painted semi-gloss
Attached Images
     
__________________
ClusterTruck: 68 C10 Bought in 89, wrecked in 03. Slow low $ rebuild started '17. 6.0 & TKO
http://67-72chevytrucks.com/vboard/s...d.php?t=788602
93 K1500 Short Step, 350, NV4500, EBL flash ECU. Vortec heads & roller cam someday...
05 Jeep Wrangler Unlimited. 3” lift & 6-speed
02 E320 the insurance total “free car”
13 Tahoe LTZ
clay68c10 is offline   Reply With Quote
Old 09-20-2020, 02:55 PM   #2
clay68c10
Senior Member
 
clay68c10's Avatar
 
Join Date: Aug 2004
Location: Centennial, CO
Posts: 2,881
Re: Tilt column "truck clone"

One more
Attached Images
 
__________________
ClusterTruck: 68 C10 Bought in 89, wrecked in 03. Slow low $ rebuild started '17. 6.0 & TKO
http://67-72chevytrucks.com/vboard/s...d.php?t=788602
93 K1500 Short Step, 350, NV4500, EBL flash ECU. Vortec heads & roller cam someday...
05 Jeep Wrangler Unlimited. 3” lift & 6-speed
02 E320 the insurance total “free car”
13 Tahoe LTZ
clay68c10 is offline   Reply With Quote
Old 09-20-2020, 09:11 PM   #3
CarlsLQ9SS
Senior Member
 
CarlsLQ9SS's Avatar
 
Join Date: Aug 2018
Location: London, Ky
Posts: 1,158
Re: Tilt column "truck clone"

Very nice!
CarlsLQ9SS is offline   Reply With Quote
Old 09-20-2020, 09:43 PM   #4
clay68c10
Senior Member
 
clay68c10's Avatar
 
Join Date: Aug 2004
Location: Centennial, CO
Posts: 2,881
Re: Tilt column "truck clone"

Thanks! My painter friend did the shiny stuff.
__________________
ClusterTruck: 68 C10 Bought in 89, wrecked in 03. Slow low $ rebuild started '17. 6.0 & TKO
http://67-72chevytrucks.com/vboard/s...d.php?t=788602
93 K1500 Short Step, 350, NV4500, EBL flash ECU. Vortec heads & roller cam someday...
05 Jeep Wrangler Unlimited. 3” lift & 6-speed
02 E320 the insurance total “free car”
13 Tahoe LTZ
clay68c10 is offline   Reply With Quote
Old 09-21-2020, 12:05 AM   #5
flashed
Registered User
 
Join Date: Oct 2009
Location: canton ga
Posts: 12,729
Re: Tilt column "truck clone"

If you need to ship it , Home Depot sells white plastic pipe with a bell on one end . Pipe has small drain holes along the length but is plenty strong for shipping a column . Cut it to length , slide the column into the big end , the top of the column just fits inside the bell, I taped thin plywood on each end and then wrapped the complete pipe in packing tape .
flashed is offline   Reply With Quote
Old 09-21-2020, 12:23 AM   #6
Curtb1971
Senior Member
 
Curtb1971's Avatar
 
Join Date: Feb 2014
Location: Erie Colorado
Posts: 1,007
Re: Tilt column "truck clone"

Clay, no need for a plastic tube. I'll take it Now I just need to trick you into coming up to the shop Give me a shout tomorrow
__________________
1971 LSX "Bonnie" build thread
http://67-72chevytrucks.com/vboard/s....php?p=8026381
paypal is curtbarton1971@yahoo.com
Curtb1971 is offline   Reply With Quote
Old 09-21-2020, 09:21 AM   #7
clay68c10
Senior Member
 
clay68c10's Avatar
 
Join Date: Aug 2004
Location: Centennial, CO
Posts: 2,881
Re: Tilt column "truck clone"

Flashed; thanks for the lead on that. I’ll look into it.

Curt; thanks man. I’ll get ahold of you sometime today.

Sold to Curt
__________________
ClusterTruck: 68 C10 Bought in 89, wrecked in 03. Slow low $ rebuild started '17. 6.0 & TKO
http://67-72chevytrucks.com/vboard/s...d.php?t=788602
93 K1500 Short Step, 350, NV4500, EBL flash ECU. Vortec heads & roller cam someday...
05 Jeep Wrangler Unlimited. 3” lift & 6-speed
02 E320 the insurance total “free car”
13 Tahoe LTZ
clay68c10 is offline   Reply With Quote
Reply

Bookmarks

Tags
column, tilt, tilt column, tilt wheel

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:32 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com