TX 1974 CCSB project - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Jonboy · 05-30-2014, 12:15 AM

I am putting my '74 CCSB project up for sale. The frame has been shortened, and it has all new 1/2 suspension under it currently. The front has been lowered with 3" Bell Tech spindles and new big block springs with 1 coil cut. The rear has the original 3/4 ton leaf springs and a rebuilt 3.73 geared 12 bolt with a new Eaton posi unit in it; lowered with a flip kit and 1/2 ton spring shackles. The truck also has new 20x8 (front) and 20x9.5 (rear) Ridler wheels with new Toyo tires; no miles on the tires. The bed is almost mint as well; the floor is clean enough that it could be painted and look like new.

I am currently in the middle of an LS swap right now. The 5.3 and 4L60E is out of a 2001 GMC Yukon, truck had just shy of 100K on it. The wiring harness is new from www.fuelinjectionconnection.com (DBW), the fuel tank was replaced with a new '87 EFI tank, along with a new FI fuel sender and Delco EP381 pump. While the engine was on the stand, I replaced the oil pan, pickup tube and dipstick with CTS-V parts for more ground clearance, water pump and intake gaskets were replaced, everything was cleaned and painted, and TBSS manifolds, Delco plugs and wires were added as well. Engine was set in place with Dirty Dingo sliding mounts as well. The gauges were upgraded to a 91 Suburban cluster, and a tach from GM Sport Salvage was added as well. I am sure there is a ton of stuff I can't remember doing right now, but it has become apparent that I will not have the time to finish the truck anytime soon. I would love to see it done, and hope it would go to a good home that would finish it. Looking for $7500 or best offer for everything I have to finish the truck. There are pics on my build thread; I will post a link to that thread tomorrow.

bbbc10 · 05-30-2014, 03:45 AM

man this sucks!!! sorry you gotta sell....got a few questions are you gonna get the ls swap running before you sell and any trades or jus cash?

Jonboy · 05-30-2014, 03:02 PM

I am still chipping away at getting it running, so that isn't an issue. I really don't have time for another project, though.

bbbc10 · 05-30-2014, 03:52 PM

that's good.....you not looking for another daily driver or anything or you want cash

05-30-2014, 12:15 AM	#1
Jonboy Slots go on anything! Join Date: May 2003 Location: Richardson, TX Posts: 5,957	1974 CCSB project I am putting my '74 CCSB project up for sale. The frame has been shortened, and it has all new 1/2 suspension under it currently. The front has been lowered with 3" Bell Tech spindles and new big block springs with 1 coil cut. The rear has the original 3/4 ton leaf springs and a rebuilt 3.73 geared 12 bolt with a new Eaton posi unit in it; lowered with a flip kit and 1/2 ton spring shackles. The truck also has new 20x8 (front) and 20x9.5 (rear) Ridler wheels with new Toyo tires; no miles on the tires. The bed is almost mint as well; the floor is clean enough that it could be painted and look like new. I am currently in the middle of an LS swap right now. The 5.3 and 4L60E is out of a 2001 GMC Yukon, truck had just shy of 100K on it. The wiring harness is new from www.fuelinjectionconnection.com (DBW), the fuel tank was replaced with a new '87 EFI tank, along with a new FI fuel sender and Delco EP381 pump. While the engine was on the stand, I replaced the oil pan, pickup tube and dipstick with CTS-V parts for more ground clearance, water pump and intake gaskets were replaced, everything was cleaned and painted, and TBSS manifolds, Delco plugs and wires were added as well. Engine was set in place with Dirty Dingo sliding mounts as well. The gauges were upgraded to a 91 Suburban cluster, and a tach from GM Sport Salvage was added as well. I am sure there is a ton of stuff I can't remember doing right now, but it has become apparent that I will not have the time to finish the truck anytime soon. I would love to see it done, and hope it would go to a good home that would finish it. Looking for $7500 or best offer for everything I have to finish the truck. There are pics on my build thread; I will post a link to that thread tomorrow. __________________ 1974 Jimmy- 5.3/4L80e/NP241

05-30-2014, 03:45 AM	#2
bbbc10 Diggin The SquareLife Join Date: Dec 2010 Location: garland,tx Posts: 1,933	Re: 1974 CCSB project man this sucks!!! sorry you gotta sell....got a few questions are you gonna get the ls swap running before you sell and any trades or jus cash?

05-30-2014, 03:02 PM	#3
Jonboy Slots go on anything! Join Date: May 2003 Location: Richardson, TX Posts: 5,957	Re: 1974 CCSB project I am still chipping away at getting it running, so that isn't an issue. I really don't have time for another project, though. __________________ 1974 Jimmy- 5.3/4L80e/NP241

05-30-2014, 03:52 PM	#4
bbbc10 Diggin The SquareLife Join Date: Dec 2010 Location: garland,tx Posts: 1,933	Re: 1974 CCSB project that's good.....you not looking for another daily driver or anything or you want cash



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.