FYI 1979 rear cclip axle will fit a 1972. - The 1947 - Present Chevrolet & GMC Truck Message Board Network

moodyholler · 08-10-2004, 05:18 PM

I got an axle from a 1979 blazer yesterdasy and put it in. It fit fine. moodyholler

badpeanut · 08-11-2004, 01:45 PM

Doesn't the '79 have staggered rear shocks and the '72 have non-staggered rear shocks? How did you bolt your shocks up?

moodyholler · 08-11-2004, 05:10 PM

I used the axle itself, not the housing. No one would/could tell me whether or not it would work. So I tried it out and viola, I'm up and running again.moodyholler

badpeanut · 08-11-2004, 07:37 PM

moodyholler, is your Blazer a 4x4?

If so, that is great news as my '71 K5 needs axles and I have some later ones.

moodyholler · 08-11-2004, 08:13 PM

I asked around and could get no answer so I threw one in. moodyholler

moodyholler · 08-11-2004, 08:17 PM

This price is for a pair. I have been fighting a bent axle for a year. I have replaced both driveshafts, four wheels and tires,axle bearings and seals. Hub of axle showed no runout, however, axle was bent about six inches from hub. Didn't find it until I took it out as I was going to start replacing bearings on carrier and pinion. Just my luck. Should drive a lot better. moodyholler

08-10-2004, 05:18 PM	#1
moodyholler Registered User Join Date: Dec 2003 Location: Roanoke,Virginia Posts: 179	FYI 1979 rear cclip axle will fit a 1972. I got an axle from a 1979 blazer yesterdasy and put it in. It fit fine. moodyholler __________________ 1998 WRANGLER I-6 auto 1972 LWB FLEETSIDE 1968 GMC SWB STEPSIDE 1994 C-1500 SWB 4.3 5 SPD

08-11-2004, 05:10 PM	#3
moodyholler Registered User Join Date: Dec 2003 Location: Roanoke,Virginia Posts: 179	Peanut I used the axle itself, not the housing. No one would/could tell me whether or not it would work. So I tried it out and viola, I'm up and running again.moodyholler __________________ 1998 WRANGLER I-6 auto 1972 LWB FLEETSIDE 1968 GMC SWB STEPSIDE 1994 C-1500 SWB 4.3 5 SPD

08-11-2004, 08:13 PM	#5
moodyholler Registered User Join Date: Dec 2003 Location: Roanoke,Virginia Posts: 179	Yeah it is a 4x4. I asked around and could get no answer so I threw one in. moodyholler __________________ 1998 WRANGLER I-6 auto 1972 LWB FLEETSIDE 1968 GMC SWB STEPSIDE 1994 C-1500 SWB 4.3 5 SPD

08-11-2004, 08:17 PM	#6
moodyholler Registered User Join Date: Dec 2003 Location: Roanoke,Virginia Posts: 179	Moser axles are 264.00 to your door. This price is for a pair. I have been fighting a bent axle for a year. I have replaced both driveshafts, four wheels and tires,axle bearings and seals. Hub of axle showed no runout, however, axle was bent about six inches from hub. Didn't find it until I took it out as I was going to start replacing bearings on carrier and pinion. Just my luck. Should drive a lot better. moodyholler __________________ 1998 WRANGLER I-6 auto 1972 LWB FLEETSIDE 1968 GMC SWB STEPSIDE 1994 C-1500 SWB 4.3 5 SPD

08-11-2004, 01:45 PM	#2
badpeanut Not a bad nut after all.. Join Date: Dec 2000 Location: ND Posts: 1,755	Doesn't the '79 have staggered rear shocks and the '72 have non-staggered rear shocks? How did you bolt your shocks up?

08-11-2004, 07:37 PM	#4
badpeanut Not a bad nut after all.. Join Date: Dec 2000 Location: ND Posts: 1,755	moodyholler, is your Blazer a 4x4? If so, that is great news as my '71 K5 needs axles and I have some later ones.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.