Pops 72 cheyenne dropmember build - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

franky69c10 · 01-25-2011, 03:54 PM

Nice can't wait 4 this build

Posted via Mobile Device

**superflysteiny** · 01-25-2011, 04:22 PM

Quote:

Originally Posted by porterbuilt

9 big boxes.... scheduled to arrive tomorrow.

Might want to get some water handy to help re-hydrate your UPS driver!

I will get the water ready

**superflysteiny** · 01-25-2011, 04:25 PM

Quote:

Originally Posted by smokinstang70

Great looking truck... good starting point... great direction... can't wait to see more of the build

Where did you get the upper side trim? I have ordered some in the past and was very disappointed in the quality. Yours looks great.

Also... where did the side marker lights come from? They are awesome!!!

Side trim is mark 5 I believe I got it from a place called chevy land in Rancho cordova CA and the side markers are marquez. They are billet and I got them for $225 for all 4.

**superflysteiny** · 01-25-2011, 04:26 PM

Quote:

Originally Posted by Raguemoe

You may as well just tear it apart now & get a head start, cuz you know you will end up doing it later! After you remove the bed & front clip for the DM stuff your already half way there. Haha just messing with you, don't listen to the voices in your head or you will have another full blown project on your hands! What's the saying "keep it simple stupid", but if that was the case we wouldn't be on this forum for hrs every day. Have fun & good luck!
Posted via Mobile Device

No I am going to build a driver. Need to stick to the plan. Thanks man it will be a fun truck and I can't wait to get it on the ground

98L150 · 01-25-2011, 04:37 PM

cant wait to see more on this one

SCOTTMO · 01-25-2011, 07:18 PM

I'm in....my back was hurting just from looking at those nine boxes the other
day...

**superflysteiny** · 01-25-2011, 07:45 PM

That funny

. Can't wait to get this stuff so I can get it painted and on the truck.

**lolife99** · 01-25-2011, 07:59 PM

What method do you use for "correct placement" of the upper moldings?
Or did the mouldings come with placement instructions?

Everything looks great!

CHYNSPR · 01-25-2011, 09:24 PM

Same question as above...also, what did you attach the trim with? Did you drill any holes?

Thanks

Smitty

**superflysteiny** · 01-26-2011, 01:47 AM

Sure I can answer that. The front fenders were drilled. So I found the old manuals on this forum that showed were and how the trim should be place. I also shows how far the holes should be placed apart. I took the measurements from the manual and the existing holes in the fenders and that was my starting point. I would tell you before you drill for the trim make sure all fender door gaps are correct and make sure bed is level and that all body mounts are good. If the mounts are old and cracked replace them first. My drivers side of the cab was lower by a quarter of an inch. So it is very important to check this before the bed is drilled. The kit was factory so it was retained with clip/nut and bolt trim tabs with plastic double sided tap. I was a long day putting the trim on because I had to almost pull the front clip off to get to the back side of the clips so I can put the nuts on. Hope this helps.
Posted via Mobile Device

CheyenneShop · 01-26-2011, 03:13 AM

I am in!! Did you do OK on your other truck? Saw it in person at B.J. looked better then I had imagined. Love your attention to detail.

Those rims are sic btw.

She got a name yet. Black with red interior - I'm thinking - Black Widow!!

trenz68 · 01-26-2011, 05:38 AM

gonna be nice

**superflysteiny** · 01-26-2011, 12:40 PM

Quote:

Originally Posted by theCheyenneShop

I am in!! Did you do OK on your other truck? Saw it in person at B.J. looked better then I had imagined. Love your attention to detail.

Those rims are sic btw.

She got a name yet. Black with red interior - I'm thinking - Black Widow!!

Glad you liked the truck. No name yet just super pumped to get this truck laid out.

**superflysteiny** · 01-26-2011, 06:48 PM

Look what I got today from porter built

SCOTTMO · 01-26-2011, 07:09 PM

Nice....Is your back ok

**67cheby** · 01-26-2011, 07:10 PM

Best day ever!!!

CheyenneShop · 01-26-2011, 07:17 PM

Christmas in January!

I'm thinking the UPS guy hates going by Nate's shop!

**superflysteiny** · 01-26-2011, 08:02 PM

Quote:

Originally Posted by SCOTTMO

Nice....Is your back ok

yep mine is great but the ups guys back is not feeling so hot

**superflysteiny** · 01-26-2011, 08:03 PM

I am so pumped about this project. I will be tearing into her on sat.morning.

Mad Rods · 01-26-2011, 08:24 PM

Awesome!!!
Posted via Mobile Device

Dinos63 · 01-26-2011, 11:41 PM

duude christmas in january!!

**superflysteiny** · 01-27-2011, 11:24 AM

hell ya

**superflysteiny** · 01-28-2011, 11:49 AM

First off I would like to say what a quality product Nate is turning out and his customer service is second to none with the exception of my buisness

But in all seriousness I am super happy with the quality and service. Also I no my truck will be safe and drive better because of his products. So thanks again Nate. Here are some pics of the products. I got the garage cleaned up last night and unpacked the boxes.

PBFAB.COM · 01-28-2011, 11:57 AM

Thanks for the kind words eric. I am pretty excited to see your build come together. It is a very clean truck and you have great plans for it.

As some know, I still haven't had the chance to put one of these trucks together for myself... yet.

It's nice to play a role in helping somebody else do it! Soon I will have my own... but for now I live vicariously through my customers' builds!

Any questions, just let me know!

Nate

**67cheby** · 01-28-2011, 12:50 PM

Wow

01-25-2011, 03:54 PM	#26
franky69c10 chevy runs deep Join Date: Mar 2006 Location: PHOENIX AZ Posts: 1,074	Re: Pops 72 cheyenne dropmember build Nice can't wait 4 this build Posted via Mobile Device __________________ RAIDER NATION 1969 c10 swb soon 2 b on the road... My LWB is a SWB now http://67-72chevytrucks.com/vboard/s...d.php?t=498241

01-25-2011, 04:37 PM	#30
98L150 ///Relaxed Atmosphere Join Date: Apr 2003 Location: Hockley, TX Posts: 657	Re: Pops 72 cheyenne dropmember build cant wait to see more on this one __________________ 72 Suburban 64 Chevy short fleet 04 Chevy Colorado Sport Reg Cab 2012 Chevy Avalanche 2003 Chevy S10 Blazer Xtreme http://www.hubgarage.com/mygarage/RA_Jeff 64 Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=295915

01-25-2011, 07:18 PM	#31
SCOTTMO powdercoater Join Date: Dec 2008 Location: mesa,az Posts: 203	Re: Pops 72 cheyenne dropmember build I'm in....my back was hurting just from looking at those nine boxes the other day... __________________ SCOTT

01-25-2011, 07:45 PM	#32
superflysteiny Senior Member Join Date: Nov 2008 Location: orangevale ca Posts: 4,630	Re: Pops 72 cheyenne dropmember build That funny. Can't wait to get this stuff so I can get it painted and on the truck. __________________ Tootsie build T Shirts (Supporting Colon Cancer research) Tootsie- a truck for my mother Pops 72 Cheyenne Dropmember build 67 Second Chance project from hell Last edited by superflysteiny; 11-30-2011 at 12:11 PM.

01-25-2011, 07:59 PM	#33
lolife99 67-72 parts collector,… Join Date: Nov 2002 Location: Mid-MO Posts: 22,682	Re: Pops 72 cheyenne dropmember build What method do you use for "correct placement" of the upper moldings? Or did the mouldings come with placement instructions? Everything looks great! __________________ Keith Convert to disc brakes. http://67-72chevytrucks.com/vboard/s...d.php?t=444823

01-25-2011, 09:24 PM	#34
CHYNSPR Registered User Join Date: Jan 2006 Location: Grande Prairie, Alberta Posts: 202	Re: Pops 72 cheyenne dropmember build Same question as above...also, what did you attach the trim with? Did you drill any holes? Thanks Smitty __________________ 1972 Cheyenne (LWB now a SWB)

01-26-2011, 01:47 AM	#35
superflysteiny Senior Member Join Date: Nov 2008 Location: orangevale ca Posts: 4,630	Re: Pops 72 cheyenne dropmember build Sure I can answer that. The front fenders were drilled. So I found the old manuals on this forum that showed were and how the trim should be place. I also shows how far the holes should be placed apart. I took the measurements from the manual and the existing holes in the fenders and that was my starting point. I would tell you before you drill for the trim make sure all fender door gaps are correct and make sure bed is level and that all body mounts are good. If the mounts are old and cracked replace them first. My drivers side of the cab was lower by a quarter of an inch. So it is very important to check this before the bed is drilled. The kit was factory so it was retained with clip/nut and bolt trim tabs with plastic double sided tap. I was a long day putting the trim on because I had to almost pull the front clip off to get to the back side of the clips so I can put the nuts on. Hope this helps. Posted via Mobile Device __________________ Tootsie build T Shirts (Supporting Colon Cancer research) Tootsie- a truck for my mother Pops 72 Cheyenne Dropmember build 67 Second Chance project from hell

01-26-2011, 03:13 AM	#36
CheyenneShop Registered User Join Date: Feb 2008 Location: Arizona Posts: 638	Re: Pops 72 cheyenne dropmember build I am in!! Did you do OK on your other truck? Saw it in person at B.J. looked better then I had imagined. Love your attention to detail. Those rims are sic btw. She got a name yet. Black with red interior - I'm thinking - Black Widow!! __________________ 72 Cheyenne shorty "*CheyLow" 72 3/4 long 4X4 69 SWB "Prospector" 68 C/10 shorty - "Picacho"* http://67-72chevytrucks.com/vboard/s...d.php?t=428379 *sold to "93redsled"* Have you heard about *C10 Talk? C10 Talk* is a podcast all about C10 Trucks, the builders, the vendors, and most importantly the C10 Community. Check us out online at www.c10talk.com

01-26-2011, 05:38 AM	#37
trenz68 Damage Inc Join Date: Dec 2008 Location: Baytown Tx Posts: 336	Re: Pops 72 cheyenne dropmember build gonna be nice __________________ 05 CC- magnacharged,LTs,Gt-2 cam,3.73s,tru-trac,tuned-sold 01 ECSB- caddy-clipped,22/24 intros,cammed,layin-frame 04 RCSB-joe gibbs clone,22in billets 68 stepper build http://67-72chevytrucks.com/vboard/s...d.php?t=332337

01-26-2011, 06:48 PM	#39
superflysteiny Senior Member Join Date: Nov 2008 Location: orangevale ca Posts: 4,630	Re: Pops 72 cheyenne dropmember build Look what I got today from porter built __________________ Tootsie build T Shirts (Supporting Colon Cancer research) Tootsie- a truck for my mother Pops 72 Cheyenne Dropmember build 67 Second Chance project from hell

01-26-2011, 07:09 PM	#40
SCOTTMO powdercoater Join Date: Dec 2008 Location: mesa,az Posts: 203	Re: Pops 72 cheyenne dropmember build Nice....Is your back ok __________________ SCOTT

01-26-2011, 07:10 PM	#41
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: Pops 72 cheyenne dropmember build Best day ever!!! __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

01-26-2011, 07:17 PM	#42
CheyenneShop Registered User Join Date: Feb 2008 Location: Arizona Posts: 638	Re: Pops 72 cheyenne dropmember build Christmas in January! I'm thinking the UPS guy hates going by Nate's shop! __________________ 72 Cheyenne shorty "*CheyLow" 72 3/4 long 4X4 69 SWB "Prospector" 68 C/10 shorty - "Picacho"* http://67-72chevytrucks.com/vboard/s...d.php?t=428379 *sold to "93redsled"* Have you heard about *C10 Talk? C10 Talk* is a podcast all about C10 Trucks, the builders, the vendors, and most importantly the C10 Community. Check us out online at www.c10talk.com

01-26-2011, 08:03 PM	#44
superflysteiny Senior Member Join Date: Nov 2008 Location: orangevale ca Posts: 4,630	Re: Pops 72 cheyenne dropmember build I am so pumped about this project. I will be tearing into her on sat.morning. __________________ Tootsie build T Shirts (Supporting Colon Cancer research) Tootsie- a truck for my mother Pops 72 Cheyenne Dropmember build 67 Second Chance project from hell

01-26-2011, 08:24 PM	#45
Mad Rods Chevy Only Tx Join Date: May 2009 Location: Pecos,Tx Posts: 1,061	Re: Pops 72 cheyenne dropmember build Awesome!!! Posted via Mobile Device __________________ Chevy Only Tx.........



Register or Log In To remove these advertisements.

01-26-2011, 11:41 PM	#46
Dinos63 chevy only Join Date: Sep 2006 Location: Phoenix, AZ Posts: 6,619	Re: Pops 72 cheyenne dropmember build duude christmas in january!! __________________ CHEVY ONLY... Nothin Else !

01-27-2011, 11:24 AM	#47
superflysteiny Senior Member Join Date: Nov 2008 Location: orangevale ca Posts: 4,630	Re: Pops 72 cheyenne dropmember build hell ya __________________ Tootsie build T Shirts (Supporting Colon Cancer research) Tootsie- a truck for my mother Pops 72 Cheyenne Dropmember build 67 Second Chance project from hell

01-28-2011, 11:49 AM	#48
superflysteiny Senior Member Join Date: Nov 2008 Location: orangevale ca Posts: 4,630	Re: Pops 72 cheyenne dropmember build First off I would like to say what a quality product Nate is turning out and his customer service is second to none with the exception of my buisness But in all seriousness I am super happy with the quality and service. Also I no my truck will be safe and drive better because of his products. So thanks again Nate. Here are some pics of the products. I got the garage cleaned up last night and unpacked the boxes. __________________ Tootsie build T Shirts (Supporting Colon Cancer research) Tootsie- a truck for my mother Pops 72 Cheyenne Dropmember build 67 Second Chance project from hell

01-28-2011, 11:57 AM	#49
PBFAB.COM Senior Member Join Date: Dec 2003 Location: Mesa,Az Posts: 3,981	Re: Pops 72 cheyenne dropmember build Thanks for the kind words eric. I am pretty excited to see your build come together. It is a very clean truck and you have great plans for it. As some know, I still haven't had the chance to put one of these trucks together for myself... yet. It's nice to play a role in helping somebody else do it! Soon I will have my own... but for now I live vicariously through my customers' builds! Any questions, just let me know! Nate __________________ www.PorterbuiltFabrication.com Phone: 480-297-2621 E-mail: sales@pbfab.com Find us on FaceBook under Porterbuilt Fabrication Specializing in Chassis and Suspension Components for your Classic Chevrolet Truck. We offer components from the following manufacturers: Porterbuilt Accuair Ridetech (Air Ride Technologies) Air Lift Wilwood Intro Unisteer ECE Gotta Show Air Lift Borgeson CPP Supporting this forum since 2003!

01-28-2011, 12:50 PM	#50
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: Pops 72 cheyenne dropmember build Wow __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.