The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board > 67-72 Chevrolet & GMC Pickups Projects and Builds

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 03-19-2018, 01:04 PM   #51
RedRider
Registered User
 
RedRider's Avatar
 
Join Date: Jan 2016
Location: Poway, CA
Posts: 356
Re: The Old Yeller Resurrection Project

Still working on an issue with re-centering the proportioning valve, what a pain! Here's the link to my troubles:

http://67-72chevytrucks.com/vboard/s...d.php?t=758471

Fortunately I've got some good helpers:

__________________
1970 C-10 "Old Yeller"
RedRider is offline   Reply With Quote
Old 03-26-2018, 02:18 PM   #52
RedRider
Registered User
 
RedRider's Avatar
 
Join Date: Jan 2016
Location: Poway, CA
Posts: 356
Re: The Old Yeller Resurrection Project

Cleaning the gutters this weekend, clearing out all that old seam sealer. Went in with a light chisel and hammer to break-up the big pieces, then hit it with the wire wheel to clean out the rest.



I was thinking about sealing it up some of the surface rust with some POR-15, it looks like others have done that. Then seam sealer and paint?
__________________
1970 C-10 "Old Yeller"
RedRider is offline   Reply With Quote
Old 03-28-2018, 04:12 PM   #53
RedRider
Registered User
 
RedRider's Avatar
 
Join Date: Jan 2016
Location: Poway, CA
Posts: 356
Re: The Old Yeller Resurrection Project

Engine is running rough at idle and when I rev the throttle, like it has a miss somewhere. I’ve checked timing and compression, new plugs/wires, (almost) new carb and intake.

I went to look for a new cap/rotor for the HEI, which runs around $30. I found a COMPLETE distributor assembly on Amazon for $45...no brainer.
__________________
1970 C-10 "Old Yeller"
RedRider is offline   Reply With Quote
Old 03-28-2018, 04:21 PM   #54
rjs53
Registered User
 
Join Date: Jan 2010
Location: nevada
Posts: 649
Re: The Old Yeller Resurrection Project

I bought the summit brand hei, I think it’s made by msd. The only thing is they don’t use the dielectric grease for insulation and can cause parts to burn up. Just something you might want to check.
__________________
2003 Dodge 2500
1969 C10
2014 Camaro SS/RS/1LE
rjs53 is offline   Reply With Quote
Old 04-11-2018, 11:03 PM   #55
RedRider
Registered User
 
RedRider's Avatar
 
Join Date: Jan 2016
Location: Poway, CA
Posts: 356
Re: The Old Yeller Resurrection Project

Big day today! Finally got the engine and brake issues ironed out and backed her out of the driveway! She sounds great, ready for some new exhaust before the paint and bodywork begins.
__________________
1970 C-10 "Old Yeller"
RedRider is offline   Reply With Quote
Old 04-17-2018, 02:52 PM   #56
RedRider
Registered User
 
RedRider's Avatar
 
Join Date: Jan 2016
Location: Poway, CA
Posts: 356
Re: The Old Yeller Resurrection Project

Here she is after a quick one-over with the power washer.

8 months ago, same spot minus trailer:


Still need to iron out some bugs before I drive over to the exhaust shop:
1) Power steering was touchy, wondering if I should just top it off or try flushing it.
2) Some of the lights don't work, gonna start investigation at the dimmer switch.
3) Engine still running a bit rough, hoping a full tank of fresh gas will help.
4) Might try some lower fender braces, seeing as my drivers side broke.
__________________
1970 C-10 "Old Yeller"
RedRider is offline   Reply With Quote
Old 04-18-2018, 10:20 AM   #57
RedRider
Registered User
 
RedRider's Avatar
 
Join Date: Jan 2016
Location: Poway, CA
Posts: 356
Re: The Old Yeller Resurrection Project

The foot dimmer switch tested bad so I took it apart and cleaned the terminals:



Works fine now.
__________________
1970 C-10 "Old Yeller"
RedRider is offline   Reply With Quote
Old 04-18-2018, 10:25 AM   #58
rjs53
Registered User
 
Join Date: Jan 2010
Location: nevada
Posts: 649
Re: The Old Yeller Resurrection Project

Way to go! I’m kinda the same, like to fix what I have if it’s worth it. And I like keeping as much of the original truck as possible.
__________________
2003 Dodge 2500
1969 C10
2014 Camaro SS/RS/1LE
rjs53 is offline   Reply With Quote
Old 04-23-2018, 10:34 AM   #59
RedRider
Registered User
 
RedRider's Avatar
 
Join Date: Jan 2016
Location: Poway, CA
Posts: 356
Re: The Old Yeller Resurrection Project

Quote:
Originally Posted by rjs53 View Post
Way to go! I’m kinda the same, like to fix what I have if it’s worth it. And I like keeping as much of the original truck as possible.
Truth! Our fridge broke this week and my wife immediately wanted to buy a new one. I told her, "Give me an hour, and if I can't fix then we can look for a new one". Turns out the compressor was caked in dust and dirt, and with a little help from an air compressor and shop vac, the fridge is now back in business.
__________________
1970 C-10 "Old Yeller"
RedRider is offline   Reply With Quote
Old 04-23-2018, 10:35 AM   #60
RedRider
Registered User
 
RedRider's Avatar
 
Join Date: Jan 2016
Location: Poway, CA
Posts: 356
Re: The Old Yeller Resurrection Project

Her maiden voyage into town for 10 gallons and a can of Seafoam:
__________________
1970 C-10 "Old Yeller"
RedRider is offline   Reply With Quote
Old 04-23-2018, 02:12 PM   #61
rjs53
Registered User
 
Join Date: Jan 2010
Location: nevada
Posts: 649
Re: The Old Yeller Resurrection Project

Truck looks good! Seafome does wonders
__________________
2003 Dodge 2500
1969 C10
2014 Camaro SS/RS/1LE
rjs53 is offline   Reply With Quote
Old 04-26-2018, 01:59 PM   #62
RedRider
Registered User
 
RedRider's Avatar
 
Join Date: Jan 2016
Location: Poway, CA
Posts: 356
Re: The Old Yeller Resurrection Project

During the test drive I noticed some rubbing at full-turn on the front passenger side tire. It appeared the tire weight was scraping, but on what I wasn't sure:



...when I pulled the tire yesterday, it appears like it was hitting the lower control arm:



My first impression was wow! that's sure cutting it close. My second thought was to grind down the control arm but maybe I'll wait for an alignment (later this week).
__________________
1970 C-10 "Old Yeller"
RedRider is offline   Reply With Quote
Old 04-30-2018, 10:25 AM   #63
RedRider
Registered User
 
RedRider's Avatar
 
Join Date: Jan 2016
Location: Poway, CA
Posts: 356
Re: The Old Yeller Resurrection Project

I was dreading alignment day, especially since I had cut the frame in half. No surprise the alignment was waaaayy off, but it looks like the SWB conversion didn't affect much:




To make things even more interesting, the truck quit on me coming home. The fuel filter was full of brown grime, which was drying out the carb. I spent an hour parked on a side-street and finally got her fired back up.
Looks like I'm going to have to pull the gas tank, as there's just too much crud in there. Do they still boil gas tanks at radiator shops?
__________________
1970 C-10 "Old Yeller"
RedRider is offline   Reply With Quote
Old 05-02-2018, 09:43 AM   #64
RedRider
Registered User
 
RedRider's Avatar
 
Join Date: Jan 2016
Location: Poway, CA
Posts: 356
Re: The Old Yeller Resurrection Project

Took my fuel tank down to the radiator/tank shop yesterday, had a tough choice to make:

1) Have old tank cleaned, leak check and re-sealed: $275

2) Buy new tank ($200 shipped from RockAuto) + have radiator shop seal it: $320


I decided to salvage the old tank. This may come back and bite me but it was in pretty good shape. Plus there's something to be said about salvaging existing parts.
__________________
1970 C-10 "Old Yeller"
RedRider is offline   Reply With Quote
Old 05-02-2018, 11:23 PM   #65
duke10
Active Member
 
duke10's Avatar
 
Join Date: Aug 2003
Location: san diego
Posts: 833
Re: The Old Yeller Resurrection Project

I don't need the bedsides but the bed trim would sure match well on my new C20.
Let me know if you want to sell those pieces. I am in Point Loma.
Thanks
duke10 is offline   Reply With Quote
Old 05-12-2018, 08:39 PM   #66
RedRider
Registered User
 
RedRider's Avatar
 
Join Date: Jan 2016
Location: Poway, CA
Posts: 356
Re: The Old Yeller Resurrection Project

Got the cleaned tank back:



Had to buy a new sending unit since the old one had rusted down to nothing:



Also bought a new starter from Autozone today. It works great, but I'm REALLY bummed that the starter tone is different now. Lots of memories associated with the sound of the original starter, they should really warn you about that difference.
__________________
1970 C-10 "Old Yeller"
RedRider is offline   Reply With Quote
Old 05-24-2018, 10:05 AM   #67
RedRider
Registered User
 
RedRider's Avatar
 
Join Date: Jan 2016
Location: Poway, CA
Posts: 356
Re: The Old Yeller Resurrection Project

Now that Old Yeller has been road-worthy for a few weeks now, it's become apparent that there's a rear main seal leak that's needs attention. This throws a wrench into my plans, as I don't have the tools or space for such a project. Some ideas:

1) GM crate engines run around $2k-$2.5k and have a 24 month/50,000 mile warranty: steel crank, roller cam, and a one-piece rear main. Add another $1k for removal and installation.

2) I found a reputable Machine shop that will remove, rebuild and install for $3k. This includes mangnaflux, machine work, new pistons, rings, bearings, pumps, valve grind, etc. They have a 3 year/100,000 mile warranty for engines installed in-house (2 year/24,000 for customer installed).

3) I could just do the rear main seal for $600 but it's been 20+ years since the last rebuild and has sat for 10 of those years...might be a time bomb.

I'm leaning towards option #2 since the engine seems to be in otherwise good shape, although dumping $3k into a 50 year old motor sounds risky. My thought is that if they mangnaflux the block and heads then that might be a worthwhile gamble. There's something to be said about keeping the original engine too. Then again, a crate motor is a hassle free option that you just drop in and go, but I won't be able to pick out my own cam or do any other custom changes.

Any thoughts out there? Any other options I should consider?
__________________
1970 C-10 "Old Yeller"
RedRider is offline   Reply With Quote
Old 05-24-2018, 02:07 PM   #68
cjohns
Registered User
 
cjohns's Avatar
 
Join Date: May 2009
Location: Anoka MN
Posts: 134
Re: The Old Yeller Resurrection Project

# 2 no question !!
cjohns is offline   Reply With Quote
Old 06-04-2018, 11:49 AM   #69
RedRider
Registered User
 
RedRider's Avatar
 
Join Date: Jan 2016
Location: Poway, CA
Posts: 356
Re: The Old Yeller Resurrection Project

....Then there's option #4: LS swap. I found a killer deal on a 2008 6.0 w/tranny under 40k miles.

Things just got real, stay tuned.
__________________
1970 C-10 "Old Yeller"

Last edited by RedRider; 06-04-2019 at 10:37 PM.
RedRider is offline   Reply With Quote
Old 06-04-2018, 12:05 PM   #70
rjs53
Registered User
 
Join Date: Jan 2010
Location: nevada
Posts: 649
Re: The Old Yeller Resurrection Project

Option #2, put the motor in yourself it’s not rocket science, and put the other grand towards the odds n ends for the crate
__________________
2003 Dodge 2500
1969 C10
2014 Camaro SS/RS/1LE
rjs53 is offline   Reply With Quote
Old 06-04-2018, 09:24 PM   #71
Rickysnickers
Senior Member

 
Join Date: Oct 2014
Location: Eagle, ID
Posts: 2,917
Re: The Old Yeller Resurrection Project

Option 4 looks pretty promising, no?
Rickysnickers is offline   Reply With Quote
Old 06-04-2018, 10:26 PM   #72
t300
Registered User
 
Join Date: Mar 2013
Location: Manitoba
Posts: 184
Re: The Old Yeller Resurrection Project

#4. cheapest bang for the buck, reliable, easy starts, just get in the truck and drive. I'd never go back. I sold my smallblock and trans for a pizza and 6 of beer. beer was cold.
t300 is offline   Reply With Quote
Old 06-04-2018, 11:01 PM   #73
RedRider
Registered User
 
RedRider's Avatar
 
Join Date: Jan 2016
Location: Poway, CA
Posts: 356
Re: The Old Yeller Resurrection Project

Quote:
Originally Posted by Rickysnickers View Post
Option 4 looks pretty promising, no?
Yep, pulled the trigger and brought home the tranny today.



It's a 4L60E out of a 2004 Silverado with 40k miles. Next trip will be for the 5.3L accompanying it.

I had NO clue about LS swaps prior to this weekend. Needless to say there's a TON of information out there to brush-up on. Thank god for the internet.

So if you know anyone in town that needs a complete and running 350/TH350 setup, let me know!
__________________
1970 C-10 "Old Yeller"
RedRider is offline   Reply With Quote
Old 06-04-2018, 11:41 PM   #74
Rickysnickers
Senior Member

 
Join Date: Oct 2014
Location: Eagle, ID
Posts: 2,917
Re: The Old Yeller Resurrection Project

Nice!
Rickysnickers is offline   Reply With Quote
Old 06-05-2018, 12:11 AM   #75
ls1nova71
Registered User
 
ls1nova71's Avatar
 
Join Date: Dec 2009
Location: Independence Mo
Posts: 4,117
Re: The Old Yeller Resurrection Project

Quote:
Originally Posted by RedRider View Post

I had NO clue about LS swaps prior to this weekend. Needless to say there's a TON of information out there to brush-up on. Thank god for the internet.
There's a sub forum on here that has all the info you should ever need. http://67-72chevytrucks.com/vboard/f...play.php?f=206 If you're getting an '04 engine, it would be best if you could get the harness, PCM, TAC module and gas pedal all out of the same truck too to cut down on mismatch component problems.
__________________
My '72 short bed build. http://www.ls1tech.com/forums/conver...6-0-4l80e.html

5.3 swap into my RUSTY '71 C10
http://ls1tech.com/forums/conversion...71-c-10-a.html
ls1nova71 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 02:06 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com