The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 04-10-2017, 07:15 PM   #1
Cadillac Kid
Registered User
 
Cadillac Kid's Avatar
 
Join Date: Jun 2016
Location: Redondo Beach, CA
Posts: 72
Question What Header Gasket?

Hello everyone.

When I bought my truck It had a pair of smog legal headman headers on it.
It has come time to put the headers back on the 350. I am a little confused on what header gaskets to get. Ive been looking on jegs and summit and seeing header gaskets with square ports, round ports, and all different dimensions.
The engine has square ports, but my headers have round ports. I am not sure what gaskets to get. Round port or square port? Here are some pictures of the exhaust ports and the headers. When I pulled the headers off, they had the cheap cardboard type gaskets on them (I don't like these).
What gasket are the proper type? Its a 1974 350 4bbl, for what its worth.

Thank you!

-Gavin
Attached Images
   
Cadillac Kid is offline   Reply With Quote
Old 04-10-2017, 07:28 PM   #2
geezer#99
Registered User
 
geezer#99's Avatar
 
Join Date: Aug 2009
Location: Bowser
Posts: 13,494
Re: What Header Gasket?

Put some stock ones on. Like this.
https://www.summitracing.com/int/par...1444/overview/
geezer#99 is offline   Reply With Quote
Old 04-10-2017, 08:22 PM   #3
Rickysnickers
Senior Member

 
Join Date: Oct 2014
Location: Eagle, ID
Posts: 2,917
Re: What Header Gasket?

They are a little more expensive, and I'm not arguing with geezer at all (!), but I prefer Reflex gaskets, https://catalog.remflex.com/CHEVROLE...ket_p/2016.htm
Rickysnickers is offline   Reply With Quote
Old 04-10-2017, 09:03 PM   #4
Jake Wade
Registered User
 
Jake Wade's Avatar
 
Join Date: Aug 2005
Location: Louisiana
Posts: 711
Re: What Header Gasket?

Felpro 1444 is the ticket for your set up. I am speaking from experience.
Jake Wade is offline   Reply With Quote
Old 04-10-2017, 09:52 PM   #5
crewcabshorty
Registered User
 
crewcabshorty's Avatar
 
Join Date: Jan 2012
Location: greenville pa 16125
Posts: 283
Re: What Header Gasket?

I use red RTV. I used to try all different kinds and styles of gaskets. A old racer told me to try the rtv . I havent had a leak since.
crewcabshorty is offline   Reply With Quote
Old 04-10-2017, 11:23 PM   #6
TrailerTrash
Registered User
 
TrailerTrash's Avatar
 
Join Date: Jun 2015
Location: PA
Posts: 441
Thumbs up Re: What Header Gasket?

Quote:
Originally Posted by Jake Wade View Post
Felpro 1444 is the ticket for your set up. I am speaking from experience.
2nd. been running these for 3 years. reused them twice with no isssues
__________________
- When the Reaper makes his deal, trust in your steel -

'77 C10 350/350 2/4 drop and a mild street engine
TrailerTrash is offline   Reply With Quote
Old 04-10-2017, 11:56 PM   #7
Cadillac Kid
Registered User
 
Cadillac Kid's Avatar
 
Join Date: Jun 2016
Location: Redondo Beach, CA
Posts: 72
Re: What Header Gasket?

Thanks for the quick responses everyone.

So the felpro 1444 with the square ports will seal even with the round header ports?

Thank you.

-Gavin
Cadillac Kid is offline   Reply With Quote
Old 04-11-2017, 12:57 AM   #8
Nick_R_23
Registered User
 
Nick_R_23's Avatar
 
Join Date: May 2016
Location: Willow, Alaska
Posts: 836
Re: What Header Gasket?

If you want an absolutely leak free gasket with zero maintenance, use the stock metal faced gaskets that you would with OEM manifolds. I've never had an aftermarket gasket come close to how well these work.
Nick_R_23 is offline   Reply With Quote
Old 04-11-2017, 03:06 AM   #9
donut
Registered User
 
donut's Avatar
 
Join Date: Aug 2009
Location: S.C.
Posts: 1,593
Re: What Header Gasket?

Quote:
Originally Posted by Cadillac Kid View Post
Thanks for the quick responses everyone.

So the felpro 1444 with the square ports will seal even with the round header ports?

Thank you.

-Gavin
Yes.

FWIW, I also like the Felpro 1444 (stock type) on my smallblocks. My 454 got red RTV and held up well until it spun a bearing.
__________________
'86 C-30 dually, 454/tbh400
'73 K-20 350/350/205 (sold )

I'm kinda like duct tape- no real purpose, but handy to have around.
donut is offline   Reply With Quote
Old 04-11-2017, 06:58 AM   #10
LT7A
Registered User
 
Join Date: Oct 2015
Location: PNW
Posts: 3,472
Re: What Header Gasket?

If you want to see some real world testing of different setups, search Gregski's build of Rusty. It's good entertainment and will give you some background. I have no personal experience with headers and have no reason to doubt any of the advice previously given above. I plan installing a set in the near term, so I jumped on this thread to check out the advice. I just remember Gregski doing a lot of experimenting -- he may have actually gone back to exhaust manifolds. In which case I apologize for pointing you in a direction that doesn't offer a solution.
LT7A is offline   Reply With Quote
Old 04-11-2017, 08:31 AM   #11
jjzepplin
Registered User
 
jjzepplin's Avatar
 
Join Date: Feb 2012
Location: Ruskin Florida
Posts: 4,538
Re: What Header Gasket?

I always file down the raised portion to be flush with the flange on the header itself. Then I make a relief cut on the flange between the first port and rear port leaving 3 separate bolting flanges. Then I use an aluminum gasket made by "Percy's". No leaks. I also use "Percy's" Flange gaskets. I also like to use the longer header bolts for the head. I made a special wrench for fitting the harder to get to bolts. A 1/4" drive socket and extension help to get in there too. A lot of work but the pay off is nice and maintenance free.
__________________
70 swb 4x4 406sbc 700r4 203/205 d60/14blt locker yadda yadda http://67-72chevytrucks.com/vboard/s...88#post6935688 Yeller
72 Blazer 2wd conversion project "No Daggum Money" http://67-72chevytrucks.com/vboard/s...d.php?t=550804 LS1-T56 3.73 LSD super budget build
Blanco-2014 Sierra SWB https://67-72chevytrucks.com/vboard/...d.php?t=810350
jjzepplin is offline   Reply With Quote
Old 04-12-2017, 09:57 PM   #12
GRADYS Performance
Registered User
 
GRADYS Performance's Avatar
 
Join Date: Dec 2013
Location: Columbus, Oh
Posts: 366
Re: What Header Gasket?

Use a gasket that matches the Port Shape of the header. Fel Pro Performance gaskets # 1426 or Mr Gasket Ultra Seal #5907 will give excellent results. There are others as well. Square gaskets will not seal at the corners on the round header flange. After running the engine through a heat cycle go back and tighten all the header bolts. May want to do that several times. You should be leak free at the head. The collector gasket and sealing can be another area of concern.
GRADYS Performance is offline   Reply With Quote
Old 04-13-2017, 12:16 AM   #13
El Dorado Jim
Registered User
 
Join Date: Dec 2009
Location: El Dorado Ca
Posts: 3,374
Re: What Header Gasket?

I am not sure what gaskets you need at the head, but at the collector, use the aluminum ones, they seem to be holding up fine on my 454's
El Dorado Jim is offline   Reply With Quote
Old 04-14-2017, 01:00 AM   #14
Cadillac Kid
Registered User
 
Cadillac Kid's Avatar
 
Join Date: Jun 2016
Location: Redondo Beach, CA
Posts: 72
Re: What Header Gasket?

Thank you for all of the great response everyone.

I picked up felpro-1444 manifold gaskets today, and Installed the headers on the motor. They matched the heads perfect and the header ports pretty well.
I got them snug and will re torque them after a few heat cycles. I'm going to pick up the soft aluminum collector gaskets as well. I know the collector can be a problem area.

Thanks

-Gavin
Cadillac Kid is offline   Reply With Quote
Reply

Bookmarks

Tags
1974, c10, exhaust, headers

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 03:25 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com