Dropping- coils or spindles? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

1971 Cheyenne · 11-02-2002, 11:49 PM

Hey,

I am considering dropping my 71 C10 and am looking at early classic industries' dropping packages. What are the adavntages of dropping with spindles instead of the lowered springs? I would be doing 2 inches with the springs or 2.5 with the spindles. i am pretty sure i am going to drop 4 inches in back.

thanks to all

crazy longhorn · 11-03-2002, 12:03 AM

The spindles will give better front end geometry than a drop spring. I have a 3" drop on a spring , & it doesnt ride/handle bad, but the ball joints have some wild angles. that cant be good for parts. also, you may be running a more expensive shock with a drop spring. with the cost of the spring & shock you could well justify the spindle price IMO. good luck.....crazy AL

1971 Cheyenne · 11-03-2002, 12:05 AM

thanks,

What about ease of putting in?

crazy longhorn · 11-03-2002, 01:09 AM

Spindles arent bad to do, just peel all the brake parts & rotors,& loosen the nuts on the balljoints then rap the knuckles sharp with a brass hammer(side shot, where the pin goes through). You will probably need a separator fork for the tie rod ends, & it would be a good time to think about balljoints/tierod ends if they are original, & repack wheel bearings/inspect brake pads. good luck.....crazy AL

ChevLoRay · 11-03-2002, 12:52 PM

I have their products on my '69. You can't beat them. They use AC/Delco, Raybestos, etc., so parts are all available locally. Their spindles will fit using your stock tie rod ends, etc. Since your truck already has discs, your conversion is a "no-brainer", so to speak.

I did a lot of other work, i.e., new ball joints, center link, idler arm, upper/lower control arm bushings and shafts, springs, shocks, so my truck really drives like a new one. I used the stock height springs on the front, but lowered the rear with their 4-inch lowering springs, and adjustable track bar with new shocks (shorter).

I recommend them. The folks at their facility are very helpful and will answer all of your questions.

1971 Cheyenne · 11-03-2002, 02:33 PM

Thanks for all the replys. does anyone have any pics of their LWB with the 2.5/4 drop? I'm looking for a drop to make it look less like a grandpa truck but not enough to make it look "slammed".

my new 72 · 11-03-2002, 04:07 PM

Here is mine with a 2.5/4 drop.

1971 Cheyenne · 11-03-2002, 07:55 PM

Thanks mynew72 for the pic.
Thats exactly the drop i want! It makes it look almost exactly leveled out, instead of the back end stickin up ^

thanks again

any others?

**72 Super** · 11-03-2002, 08:42 PM

here is mine although it is 3/5 inch drop.

11-02-2002, 11:49 PM	#1
1971 Cheyenne Registered User Join Date: Nov 2002 Location: Bellevue, WA Posts: 1,480	Dropping- coils or spindles? Hey, I am considering dropping my 71 C10 and am looking at early classic industries' dropping packages. What are the adavntages of dropping with spindles instead of the lowered springs? I would be doing 2 inches with the springs or 2.5 with the spindles. i am pretty sure i am going to drop 4 inches in back. thanks to all __________________ Brian Pal 1971 Cheyenne 10 454/th400-Undergoing a full frame off resto. 1972 Chevy short/step 2wd, 350/th350 1983 M1009 CUCV Military K5 Blazer 1981 Dodge 1 ton 4x4 dually flatbed

11-03-2002, 12:05 AM	#3
1971 Cheyenne Registered User Join Date: Nov 2002 Location: Bellevue, WA Posts: 1,480	thanks, What about ease of putting in? __________________ Brian Pal 1971 Cheyenne 10 454/th400-Undergoing a full frame off resto. 1972 Chevy short/step 2wd, 350/th350 1983 M1009 CUCV Military K5 Blazer 1981 Dodge 1 ton 4x4 dually flatbed

11-03-2002, 12:52 PM	#5
ChevLoRay Old Skool Club Join Date: Jun 2001 Location: Benton, AR "The Heart of Arkansas" Posts: 10,880	I have their products on my '69. You can't beat them. They use AC/Delco, Raybestos, etc., so parts are all available locally. Their spindles will fit using your stock tie rod ends, etc. Since your truck already has discs, your conversion is a "no-brainer", so to speak. I did a lot of other work, i.e., new ball joints, center link, idler arm, upper/lower control arm bushings and shafts, springs, shocks, so my truck really drives like a new one. I used the stock height springs on the front, but lowered the rear with their 4-inch lowering springs, and adjustable track bar with new shocks (shorter). I recommend them. The folks at their facility are very helpful and will answer all of your questions. __________________ Member Nr. 2770 '96 GMC Sportside; 4.3/SLT - Daily driven....constantly needs washed. '69 C-10 SWB; 350/TH400 - in limbo The older I get, the better I was.

11-03-2002, 02:33 PM	#6
1971 Cheyenne Registered User Join Date: Nov 2002 Location: Bellevue, WA Posts: 1,480	Thanks for all the replys. does anyone have any pics of their LWB with the 2.5/4 drop? I'm looking for a drop to make it look less like a grandpa truck but not enough to make it look "slammed". __________________ Brian Pal 1971 Cheyenne 10 454/th400-Undergoing a full frame off resto. 1972 Chevy short/step 2wd, 350/th350 1983 M1009 CUCV Military K5 Blazer 1981 Dodge 1 ton 4x4 dually flatbed

11-03-2002, 04:07 PM	#7
my new 72 faster, faster, faster Join Date: Dec 2001 Location: Houston ,Texas ,USA Posts: 1,354	Here is mine with a 2.5/4 drop. __________________ I'm going to Law School, wanna debate? It's good practice.

11-03-2002, 12:03 AM	#2
crazy longhorn Fabricate till you "puke" Join Date: Jun 2002 Location: Ill Posts: 9,403	The spindles will give better front end geometry than a drop spring. I have a 3" drop on a spring , & it doesnt ride/handle bad, but the ball joints have some wild angles. that cant be good for parts. also, you may be running a more expensive shock with a drop spring. with the cost of the spring & shock you could well justify the spindle price IMO. good luck.....crazy AL

11-03-2002, 01:09 AM	#4
crazy longhorn Fabricate till you "puke" Join Date: Jun 2002 Location: Ill Posts: 9,403	Spindles arent bad to do, just peel all the brake parts & rotors,& loosen the nuts on the balljoints then rap the knuckles sharp with a brass hammer(side shot, where the pin goes through). You will probably need a separator fork for the tie rod ends, & it would be a good time to think about balljoints/tierod ends if they are original, & repack wheel bearings/inspect brake pads. good luck.....crazy AL

11-03-2002, 07:55 PM	#8
1971 Cheyenne Registered User Join Date: Nov 2002 Location: Bellevue, WA Posts: 1,480	Thanks mynew72 for the pic. Thats exactly the drop i want! It makes it look almost exactly leveled out, instead of the back end stickin up ^ thanks again any others? __________________ Brian Pal 1971 Cheyenne 10 454/th400-Undergoing a full frame off resto. 1972 Chevy short/step 2wd, 350/th350 1983 M1009 CUCV Military K5 Blazer 1981 Dodge 1 ton 4x4 dually flatbed

11-03-2002, 08:42 PM	#9
72 Super Senior Member Join Date: Jul 2001 Location: Hyattsville, Maryland Posts: 3,678	here is mine although it is 3/5 inch drop. Attached Images __________________ 72 Cheyenne Super (Purchased new by my parents in August of 71) Black and White



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.