The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 08-09-2016, 12:37 PM   #1
mmanzanares18
Registered User
 
Join Date: Mar 2016
Location: Denver, CO
Posts: 4
Restore/Repaint 1971 Lower Side Molding

Hi everyone! First post so I don't really know what I am doing; really hope to get some good replies because I can not find anything searching on google. I am looking to repaint black on my lower trim/molding for my 1971 longbed c10 pickup. The trim is in really good condition, straight with minor chips on chrome lining. I plan to clean the chrome looking part and then tape it off really well. Then use black spray paint and then a clear coat to seal in the black and make it shine. This is way better than purchasing a new kit ($350-$500) and I sill have all the mounting hardware. I guess I am just asking if anyone has every done this, and if you could point me in the right direction for black spray paint and the clear. Of course I will first try on a extra piece before doing anything.

Thank you! I just turned 17 and purchased the truck this past october and hope to have it ready by the time school starts. I have been working with a friend to mechanically restore it and get a daily driver exterior job. No more than $6000 has been spent and I plan to purchase about $700 of random parts including a new rear bumper.
mmanzanares18 is offline   Reply With Quote
Old 08-09-2016, 01:34 PM   #2
DT1
Registered User
 
DT1's Avatar
 
Join Date: Oct 2009
Location: Gardnerville Nv No Mo Cali!!
Posts: 869
Re: Restore/Repaint 1971 Lower Side Molding

Hi, and welcome. It's great to see younger folk interested in these trucks. I'm currently restoring a 72 with my 15 YO Grandson. The trim can be cleaned up and repainted but it's not a very easy task, but it's well worth the effort. The original stuff has a clear anodizing that will have to be removed before you start buffing it up. You can strip it with of solution of Sodium Hydroxide (Lye) and water. The lye can be got from EBAY. Some guys on this board have used other stuff like Greased Lightning or EZ-OFF oven cleaner but I've not had good results with it. I use a red Scotch Brite pad with my solution. A little scrubbing will completely strip the anodizing off. To buff it out, I stack three Scotch Bright pads that I cut into 6 inch diameter disks and stack together. This takes the heavy scratches off and puts an even sheen on it. I change to a denim buffing wheel and cutting compound to bring back the shine. You can use just about any black paint followed up with a clear coat. I use SEM Trim black and a good automotive clear coat. These pictures are from my 71 that was done a few years ago and the trim still looks a good as new. You may PM me if you need more detail. Good luck!



DT1 is offline   Reply With Quote
Old 08-09-2016, 02:36 PM   #3
kingNothing
Registered User
 
kingNothing's Avatar
 
Join Date: Apr 2015
Location: Boaz,Al
Posts: 209
Re: Restore/Repaint 1971 Lower Side Molding

DT1, is the woodgrain new? If so where can you get it at?
__________________
Yeah' well sometimes nothin' can be a real cool hand

Lucas Jackson
kingNothing is offline   Reply With Quote
Old 08-09-2016, 02:50 PM   #4
Mapearso
Registered User
 
Join Date: Oct 2008
Location: los angeles, ca
Posts: 926
Re: Restore/Repaint 1971 Lower Side Molding

you can get the new woodgrain tape from LMC. Others may have it as well...
__________________
1972 C10 SWB Cheyenne Super 350/350
http://67-72chevytrucks.com/vboard/s...d.php?t=691825

1972 C10 SWB 454/400 Cheyenne Super Project
http://67-72chevytrucks.com/vboard/s...t=Project+KISS
Mapearso is offline   Reply With Quote
Old 08-09-2016, 04:05 PM   #5
jocko
Senior Member
 
jocko's Avatar
 
Join Date: Oct 2009
Location: Godley, TX
Posts: 17,922
Re: Restore/Repaint 1971 Lower Side Molding

Have you had any issues with the sem paint peeling or flaking off the metal?
jocko is offline   Reply With Quote
Old 08-09-2016, 05:05 PM   #6
DT1
Registered User
 
DT1's Avatar
 
Join Date: Oct 2009
Location: Gardnerville Nv No Mo Cali!!
Posts: 869
Re: Restore/Repaint 1971 Lower Side Molding

Quote:
Originally Posted by jocko View Post
Have you had any issues with the sem paint peeling or flaking off the metal?
Oh Yea, I forgot to mention...Before I applied the trim paint or clear coat, I wiped it down with a lint free cloth wetted with acetone. After masking, I applied SEM rattle can, metal etching primer (Very light coat) to the area to be sprayed black. Then, after putting the black on, I applied the clear to the entire thing. It's been around five years now and it still looks great.
DT1 is offline   Reply With Quote
Old 08-09-2016, 09:08 PM   #7
KY_GMC
Registered User
 
KY_GMC's Avatar
 
Join Date: Dec 2012
Location: Fort Thomas, KY
Posts: 288
Re: Restore/Repaint 1971 Lower Side Molding

I'm in the middle of doing the same thing on my 72 GMC Super Custom.

I have been using either Easy Off or Hair and Grease Drain cleaner with good results to remove the clear anodizing.

Also, get some 1/4" vinyl pin-striping tape for masking the lines. It is a lot easier to form straight lines that the paper tape and it creates a sharp paint edge. Just remember to stretch the tape as you put it down. Takes some time learning the technique, but it will give you great results. Also, remove the tape right after you are down painting.

Also, for a durable finish, look at some of the 1K paint in spray cans. They have an adjustable nozzle spray pattern that helps get the paint where you need it.
__________________
1972 GMC 1500 Super Custom, 383 Stoker, TH350

Build Thread
http://67-72chevytrucks.com/vboard/s...d.php?t=592157
Engine Thread
http://67-72chevytrucks.com/vboard/s...d.php?t=592233
KY_GMC is offline   Reply With Quote
Old 08-10-2016, 02:03 PM   #8
mmanzanares18
Registered User
 
Join Date: Mar 2016
Location: Denver, CO
Posts: 4
Re: Restore/Repaint 1971 Lower Side Molding

WOW! Thanks for the great replies guys DT1 i will probably follow those directions closely. I'll let you know how its going and then post pics of the truck when it comes back from paint and body if you all would like. Thanks again!
mmanzanares18 is offline   Reply With Quote
Old 08-10-2016, 03:42 PM   #9
35boulder
Registered User
 
35boulder's Avatar
 
Join Date: Oct 2015
Location: Dallas Texas
Posts: 1,380
Re: Restore/Repaint 1971 Lower Side Molding

Subscribed...
35boulder is offline   Reply With Quote
Old 08-16-2016, 11:05 AM   #10
mmanzanares18
Registered User
 
Join Date: Mar 2016
Location: Denver, CO
Posts: 4
Re: Restore/Repaint 1971 Lower Side Molding

One more question anyone can answer. I was just wondering what black trim finish would look the best and most original? SEM in black have satin, jet, gloss, charcoal metallic, and regular black.
mmanzanares18 is offline   Reply With Quote
Old 08-16-2016, 11:11 AM   #11
KY_GMC
Registered User
 
KY_GMC's Avatar
 
Join Date: Dec 2012
Location: Fort Thomas, KY
Posts: 288
Re: Restore/Repaint 1971 Lower Side Molding

I am using Spray Max 1K Trim Paint Satin Black for my trim. It is a durable finish and the satin looks good against the painted body.
__________________
1972 GMC 1500 Super Custom, 383 Stoker, TH350

Build Thread
http://67-72chevytrucks.com/vboard/s...d.php?t=592157
Engine Thread
http://67-72chevytrucks.com/vboard/s...d.php?t=592233
KY_GMC is offline   Reply With Quote
Old 09-20-2016, 10:56 AM   #12
mmanzanares18
Registered User
 
Join Date: Mar 2016
Location: Denver, CO
Posts: 4
Re: Restore/Repaint 1971 Lower Side Molding

Hey Guys! I know it's been a minute I just wanted to give an update on the project. I completed it about a month ago along with the rest of the truck (it's never completed but for now until I start working again) just in time for school!
Attached Images
     
mmanzanares18 is offline   Reply With Quote
Reply

Bookmarks

Tags
chrome, exterior trim, paint type, trim molding, trim moulding

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 01:19 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com