67-72 Chevy Truck fuel gauge diagnostics 101

[Shotgunn]

I may need therapy before this task is accomplished...
Gauge is at 3 o'clock position..
new tank/sending unit/ wires go all they way into the cab..proper ground.(LMC under bed tank)
pull the brown wire clip out of the fuse block and it reads 92 ohms with a full tank of gas. plug the clip back into the fuse block an check it while plugged in..32 ohms..back feed? I have 12.6 volts at the #3 on the plug with the key on. the battery and temperature gauge is disconnected. after market gauges installed oil/volts/temp.

[Hoodogie]

I pulled my gauge cluster out during my resto and I replaced the circuit strip thing on the back because my temp gauge wasn't working. When I put it back together the gas gauge was at 3'oclock and before that it worked fine. I found out by reaching up behind the dash that I forgot to tighten the two nuts that hold the circuit strip to the gas gauge. As I was tightening the nuts the gauge move to 3/4 full and did not move so I attached a ground wire to the bottom terminal of the gauge and went down and put some gas in it then the gauge move to a bit over full. I did drive it a little bit the gauge is now at the full mark so it did move just not sure if its accurate yet. going to have to drive it a little more and carry a gallon with me.

[TBONE1964]

Originally Posted by Shotgunn

I may need therapy before this task is accomplished...
Gauge is at 3 o'clock position..
new tank/sending unit/ wires go all they way into the cab..proper ground.(LMC under bed tank)
pull the brown wire clip out of the fuse block and it reads 92 ohms with a full tank of gas. plug the clip back into the fuse block an check it while plugged in..32 ohms..back feed? I have 12.6 volts at the #3 on the plug with the key on. the battery and temperature gauge is disconnected. after market gauges installed oil/volts/temp.

Lets try and make it simple.

First using a test light, check for power right at the fuel gauge with the key in the run position. Is there power at the gauge? Or prefered use a meter and see what the actual voltage is. It should be 12.6 or so with just key on and engine not running. if you have 12.6 that means the circuit board is OK.

If you do not have 12.6, check the gauge fuse. The #3 pink wire at the connector is the gauge power and it powers both the fuel gauge and temp gaughe. If the circuit board touchs ground when the key is on, that will blow the fuse. You need to protect that terminal on the circuit board or use a stock temp gauge and connect it as designed. Not sure this is an issue but you should check.

You can also run a wire from the sending unit to the the back of the gauge. This will by pass the path of the tan wire. If this makes the fuel gauge work, the is a problem between the signal terminal on the gauge and the terminal at the sender for the signal wire.

Let me know if this helps you. It is easy to check your tank and sending unit for ground. Run a test light from the positive side of your battery and touch it to the sending unit. If test light lights, you have good ground at sending unit.

Tom

[Shotgunn]

i have 11.8 volts on the top post of the gauge. seems low because my battery is 12.4 at the battery. all my lights in the dash work including the dimmer switch for the headlights and background light dimming.
If i have 92 ohms at the brown wire plug before i plug into the fuse block i shouldnt have to do any further checks on the sending unit..92 ohms is the correct reading for a fuel tank right?

[Shotgunn]

it must be a bad gauge. i ran a jumper wire from the brown wire plug ( the one that plugs into the fuse block ) to the signal post on the gauge and the needle came back up to the 3 o'clock position. i noticed when i unplugged the brown wire clip from the fuse block, the needle took a nose dive to the 530 position.

[Shotgunn]

Should I try a new gauge?

[Shotgunn]

I guess I’m being ignored

[TBONE1964]

Originally Posted by Shotgunn

I guess I’m being ignored

Not ignoring you, just very busy and way behind.

Based on your diagnostics and what I can tell by reading your post, I would try a new gauge. Remember some new aftermarket gauges do not require a external resistor to work.

Hope this helps,
Tom

[67 Burb]

You may need a new gauge, but before doing that, I would test the gauge itself. Here's what I use for testing a 90 ohm fuel gauge.