The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1969 - 1972 Blazers and Jimmys Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 09-03-2012, 03:29 PM   #1
PDXk5
Senior Member
 
PDXk5's Avatar
 
Join Date: Aug 2012
Location: Portland, OR
Posts: 918
Greetings

Greetings,

I’m new to here. I am a recent owner of a 1972 K5 Blazer and see that this forum is a good resource.

This is a project rig. It was my father-in-law’s truck, which he bought brand new. He has generally kept everything original and kept everything that came with the truck. I have the original owners manual (with protect-o-plate), rear spare tire holder, rear seat, original purchase agreement and service manual that he gave me with the truck.

It’s a manual 4x4, (originally Medium Red now faded to) orange, black interior, 350 ci V8. The truck is awesome. I have always shared with him that if he ever decided to sell it, to talk to me first. I took delivery of the rig on June 29th and have been cleaning and polishing the surfaces to make it a bit more presentable since then.

The truck was only washed (more sprayed down) once a year and never waxed. It served as a daily driver for a good portion of its life until it migrated to only being used for camping and hunting trips. A few years back it was covered with a tarp and put on the side of the house. It appears to be very mechanically sound, it starts first try every time and while the interior and exterior have had hard years, most everything seems to be in working order.

I drove it a bit over 250 miles from his place to ours and the drive was fine. Two things I noticed during the drive: It has a lot of play in the steering and the driver side hub is stuck in the locked position. I’m going to dig into the hub to see if I can diagnose and correct the issue. This fall, I would like to convert it to Power Steering and at that time hopefully also fix the play in the steering. I checked out the steering this last weekend. I noticed that the steering wheel and steering shaft move (in sync with one another) about 2.5 inches from top/center of steering wheel to left and 2.5 inches from top/center of steering wheel to right (5 inches total) without anything else moving. My dad used to have a 1970 Ford 4x4 with manual steering, it did not have this much play. This bothers me and I want to eliminate or greatly reduce it.

Because I was planning on converting it to power steering I figured that, when I replace the steering box that would address that component. The Tie rod ends look tight although I’m not sure how to determine if the gaskets are worn out (after 40 years, seems like a good idea to replace them). At the same time I am messing with the steering, I thought I would replace the steering column to a tilt type and change the steering wheel to a smaller diameter one. I’m guessing the smaller steering wheel will also make the play seem less noticeable. I have basic mechanic skills and consider myself handy and while I have long term plans to do more extensive work on the truck these are the two tasks at hand. I have done a bit of searching online and this forum but do you have suggestions or comments to help? I believe I'm going to purchase parts from LMC or Classic Industries. Will be making purchase of parts/materials during this month and will try to tackle power steering conversion in October.

Thanks - PDXBlazer


These photos are from when I took delivery of the rig - after a quick wash. I have since spent time on polishing and cleaning/degreasing and it looks much better - will post updates as I go.



IMG_7577 by Luftwaffepdx, on Flickr


IMG_7578 by Luftwaffepdx, on Flickr


IMG_7576 by Luftwaffepdx, on Flickr


IMG_7579 by Luftwaffepdx, on Flickr


IMG_7585 by Luftwaffepdx, on Flickr


IMG_7582 by Luftwaffepdx, on Flickr


IMG_7580 by Luftwaffepdx, on Flickr


IMG_7586 by Luftwaffepdx, on Flickr


IMG_7588 by Luftwaffepdx, on Flickr


IMG_7589 by Luftwaffepdx, on Flickr
PDXk5 is offline   Reply With Quote
Old 09-03-2012, 07:18 PM   #2
briank
Registered User
 
Join Date: Sep 2011
Location: Leland, Il
Posts: 1,503
Re: Greetings

Can't help you on the steering but that's an awesome rig....Welcome!!
Posted via Mobile Device
briank is offline   Reply With Quote
Old 09-03-2012, 10:52 PM   #3
oldschool18
Registered User
 
oldschool18's Avatar
 
Join Date: Jan 2010
Location: Hollidaysburg, PA
Posts: 785
Re: Greetings

Thats a nice starter rig
__________________
_________________________________

62 Impala
70 C-10 LWB
71 K-10 SWB
85 C-10 LWB==SOLD
01 2500 HD

Members Met......2003Silverado (Dave)
oldschool18 is offline   Reply With Quote
Old 09-03-2012, 10:59 PM   #4
Thelast 72k5
Registered User
 
Join Date: Aug 2012
Location: Finger TN.
Posts: 32
Re: Greetings

Very nice... Wish my 2wd project was close to as solid as yours.
Thelast 72k5 is offline   Reply With Quote
Old 09-03-2012, 11:19 PM   #5
hilljob26
Registered User
 
hilljob26's Avatar
 
Join Date: Dec 2004
Location: Gypsum Kansas 67448
Posts: 1,681
Re: Greetings

sweet,, thats a heck of alot better dshape then what im starting with..i will be posting a 4x4 power steering box and pump assembly in a couple weeks that i am taking off mine
__________________
21 2500hd duramax
58 apache

HILLJOB GRAPHIX--for all your graphic needs
My build thread
http://67-72chevytrucks.com/vboard/s...d.php?t=542497
LS ENGINE SWAP INFORMATION THREAD
http://67-72chevytrucks.com/vboard/s...d.php?t=377348
4l60 to an NP205
http://67-72chevytrucks.com/vboard/s...43#post3697343
hilljob26 is offline   Reply With Quote
Old 09-04-2012, 12:14 AM   #6
bouncytruck
SKINNY TIRES RULE!
 
bouncytruck's Avatar
 
Join Date: Sep 2001
Location: Bothell, WA
Posts: 11,049
Re: Greetings

Welcome to the board from Seattle. I'm from Coos Bay and went to school at OSU.

Very nice looking rig. Try buffing the paint, I think you'll be surprised how much shine you'll get out of it.

For the steering, how does the rag joint look. They tend to wear and cause play. It might be worth fixing now if you're going to drive it - we do have at least a couple more weeks of nice weather left in the pacific NW and they make awesome snow rigs!
__________________
bouncytruck 1972 K5
The Hauler 1994 K1500 Suburban
The Daily2010 Kia Soul
Wife's Ride2014 Fiat 500L
bouncytruck is offline   Reply With Quote
Old 09-04-2012, 02:50 AM   #7
Tomahawk30
Registered User
 
Tomahawk30's Avatar
 
Join Date: Jun 2010
Location: Russellville, KY
Posts: 955
Re: Greetings

Welcome from Eastern Oregon! Looks like a nice solid start compared to most!!!
__________________
1979 Silverado C10 Shortbox - Photo Album
1977 Silverado K20 Camper Special - Photo Album

1972 C10 Custom Deluxe Highlander - sold
1971 Cheyenne Super Longhorn -sold
1972 Cheyenne Super SWB 4x4 -sold, bought back, sold again... I'm dumb.
1970 Chevy C10 SWB "Sprout" -sold
1972 Cheyenne K20 -sold
1969 GMC Shortbox Stepside 4x4 -sold
1972 GMC Jimmy 4x4 -sold
Tomahawk30 is offline   Reply With Quote
Old 09-04-2012, 08:10 AM   #8
briank
Registered User
 
Join Date: Sep 2011
Location: Leland, Il
Posts: 1,503
Re: Greetings

Are you gonna restore it or just go through it mechanically? It would almost be a shame to restore it since its so original.
Posted via Mobile Device
briank is offline   Reply With Quote
Old 09-04-2012, 10:11 AM   #9
jaros44sr
Registered User
 
jaros44sr's Avatar
 
Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,408
Re: Greetings

Very nice starting point, pull up the rubber mat, carefully, and see what is under there. Since it has lost the passenger side door seal, you might have rust in the floor area.

Since you are in the portland are, i would contact wes at classic heartbeats, he uses the resto parts he sells and will give you good info. on the quality of the parts he sells. Plus, it will save you money on shipping. Plus, plus, use our clssified board to buy oem parts, fit is always perfect, and you might save some bucks

Cheapest place to start on the steering slop is the rag joint, as said above, but i think there is an adjustment nut in the steering box. Check the frame, where the box is mounted, they have been known to crack there, should have a frame doubler in that area also

Good luck on your build, and keep us posted on your progress with lots of pics, we luv pics

PS, check all the safety items first, before driving too much, wouldnt want you to get hurt
__________________
Semper Fi...Uncle Sam, you da man

All parts offered to help are free, unless otherwise noted

Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training
SAFETY FIRST

AS usual, off topic

They say your mind goes second, can't remember the first


Jim
jaros44sr is offline   Reply With Quote
Old 09-19-2014, 08:13 AM   #10
Senorx
Registered User
 
Senorx's Avatar
 
Join Date: Jan 2014
Location: South Texas
Posts: 567
Re: Greetings

I'd love to see what it's looking like two years later. Hope you kept the steelies.
Senorx is offline   Reply With Quote
Old 09-19-2014, 09:22 AM   #11
bl705k
Registered User
 
Join Date: Mar 2006
Location: ct
Posts: 34
Re: Greetings

wow thats a nice clean k5 enjoy!
bl705k is offline   Reply With Quote
Old 09-27-2014, 07:27 PM   #12
PDXk5
Senior Member
 
PDXk5's Avatar
 
Join Date: Aug 2012
Location: Portland, OR
Posts: 918
Re: Greetings

So, I have had some inquiries for some updates. First, one of the forum members wanted to have some photos of the exhaust, since it's believed to be original.


image by Luftwaffepdx, on Flickr


image by Luftwaffepdx, on Flickr



image by Luftwaffepdx, on Flickr


image by Luftwaffepdx, on Flickr


image by Luftwaffepdx, on Flickr

image by Luftwaffepdx, on Flickr

image by Luftwaffepdx, on Flickr
PDXk5 is offline   Reply With Quote
Old 09-27-2014, 10:57 PM   #13
Senorx
Registered User
 
Senorx's Avatar
 
Join Date: Jan 2014
Location: South Texas
Posts: 567
Re: Greetings

Nice! I'm doing exhaust very soon and wanted to go back to the original. The PO had a total mess done to the exhaust system.
Senorx is offline   Reply With Quote
Old 09-29-2014, 01:43 AM   #14
PDXk5
Senior Member
 
PDXk5's Avatar
 
Join Date: Aug 2012
Location: Portland, OR
Posts: 918
Re: Greetings

The first thing I had to do was replace the mirrors. They were all fogged and you couldn't see out of them.

Next, I replaced the torn original floor mats. Here is what I found underneath. Very clean (after I actually cleaned out the dirt). There was some surface rust in the floor of the front seats and a small portion of rust through at both kick panels, where the kick panels meet the floor. I will need to repair this but have not yet. I think this is pretty solid and in good condition from what I understand many of these rigs have.

IMG_7755 by Luftwaffepdx, on Flickr
IMG_7758 by Luftwaffepdx, on Flickr

IMG_7759 by Luftwaffepdx, on Flickr

IMG_7757 by Luftwaffepdx, on Flickr

IMG_7756 by Luftwaffepdx, on Flickr

I should have taken pictures of the bed after I cleaned it. NO RUST and the original color is amazing with no fading since it has been covered its whole life.

IMG_7733 by Luftwaffepdx, on Flickr

IMG_7734 by Luftwaffepdx, on Flickr
PDXk5 is offline   Reply With Quote
Old 09-29-2014, 02:15 AM   #15
PDXk5
Senior Member
 
PDXk5's Avatar
 
Join Date: Aug 2012
Location: Portland, OR
Posts: 918
Re: Greetings

I tackled the driver side hub. It was stuck in the locked position. I took it apart, saw that the gaskets had failed and the gears, spring and retainer were very rusted. I removed everything, dropped them in an acid etch rust remover and they cleaned up nicely. Greased everything, put in new O-rings and put it back together - everything works great now.

IMG_8132 by Luftwaffepdx, on Flickr

IMG_8011 by Luftwaffepdx, on Flickr

IMG_8136 by Luftwaffepdx, on Flickr

IMG_8143 by Luftwaffepdx, on Flickr

IMG_8146 by Luftwaffepdx, on Flickr

IMG_8149 by Luftwaffepdx, on Flickr

IMG_8150 by Luftwaffepdx, on Flickr

IMG_8153 by Luftwaffepdx, on Flickr

IMG_8154 by Luftwaffepdx, on Flickr

IMG_8158 by Luftwaffepdx, on Flickr

Scrubbed the exterior of the hubs, painted them and got the rims painted and new rubber too...

image by Luftwaffepdx, on Flickr
PDXk5 is offline   Reply With Quote
Old 09-29-2014, 06:34 AM   #16
notsolo
Registered User
 
notsolo's Avatar
 
Join Date: Apr 2008
Location: Md
Posts: 2,446
Re: Greetings

Great photo's, Nice to see an original survivor. Thanks for sharing the hub break down.
notsolo is offline   Reply With Quote
Old 09-29-2014, 12:33 PM   #17
IronCanine
I'm trying....
 
IronCanine's Avatar
 
Join Date: Oct 2013
Location: Athens, GA
Posts: 2,531
Re: Greetings

Thanks for the photos. I really appreciate it. Awesome Blazer.
IronCanine is offline   Reply With Quote
Old 09-29-2014, 01:23 PM   #18
Senorx
Registered User
 
Senorx's Avatar
 
Join Date: Jan 2014
Location: South Texas
Posts: 567
Re: Greetings

Are those 31x10.50 tires? Nice pics and update. Keep em coming.
Senorx is offline   Reply With Quote
Old 10-01-2014, 05:50 PM   #19
Yukon Jack
Post Whore
 
Yukon Jack's Avatar
 
Join Date: Feb 2000
Location: Rose Hill, KS, USA
Posts: 12,683
Re: Greetings

That is a really nice Blazer. Glad you're enjoying it! Don't see them that rust free very often.
__________________
1970 Blazer with a 400 sbc and 4" lift
1980 Pontiac Trans Am, 455 Oldsmobile
2012 Kawasaki Concours 14
Yukon Jack is offline   Reply With Quote
Old 10-01-2014, 09:15 PM   #20
PDXk5
Senior Member
 
PDXk5's Avatar
 
Join Date: Aug 2012
Location: Portland, OR
Posts: 918
Re: Greetings

So, hopefully I will not offend anyone moving forward with the next things. I want the rig to look original but be comfortable and a bit more fun to drive with advances that have occurred since 1972. I'm thinking of it as a resto rod.

I converted the rig to power steering (separate post). This makes the rig easy to drive and eliminated the excessive play! While doing this, I replaced the steering column to put in a tilt column and a SS Chevelle style steering wheel. I had troubles with getting the canceling cam to work correct and turn off the signals as well as getting the horn to work correctly but after much frustration, it's done and everything works.
http://67-72chevytrucks.com/vboard/s...power+steering


Steering wheel by Luftwaffepdx, on Flickr
PDXk5 is offline   Reply With Quote
Old 10-02-2014, 03:29 PM   #21
cleszkie
Registered User
 
cleszkie's Avatar
 
Join Date: Feb 2003
Location: Santa Ana, CA
Posts: 2,191
Re: Greetings

Very nice Blazer. I'm glad to see it stay in your family and end up in the hands of an apparently mechanically inclined person who will take proper care of it. Keep posting pics of the progress!
cleszkie is offline   Reply With Quote
Old 10-02-2014, 04:06 PM   #22
DeadheadNM
Carpe manana

 
DeadheadNM's Avatar
 
Join Date: Dec 2010
Location: Eau Claire, WI
Posts: 12,261
Re: Greetings

Very nice K5! Thanks for posting. I'll bet that OEM paint would really shine after a buff and wax. Check out this before/after pic of an OEM paint truck I recently had detailed: http://67-72chevytrucks.com/vboard/s...56&postcount=4
__________________
1972 K5 CST Highlander Blazer: http://67-72chevytrucks.com/vboard/s...d.php?t=708547
1972 K20 Cheyenne Super: http://67-72chevytrucks.com/vboard/s...d.php?t=528308

Members met: ORANGBLAZ, 2003 silverado, MikeCofield, BB72CHEVKT, Duncan&Son, Sameyrasmea72, THENEWMEXICAN, HotRod C/10, brianthelion02, Sport/Truck, ryanroo, michael bustamante, Dirt's72, Already Gone, WestButteTruck, 57taskforce, Moreyel, painterljp, AASmedic, SoCoC10, Lumaestas, carbuff382, Chevyland
DeadheadNM is offline   Reply With Quote
Old 10-05-2014, 09:56 PM   #23
PDXk5
Senior Member
 
PDXk5's Avatar
 
Join Date: Aug 2012
Location: Portland, OR
Posts: 918
Re: Greetings

Quote:
Originally Posted by Senorx View Post
Are those 31x10.50 tires? Nice pics and update. Keep em coming.

They are 31x10.5 on the original stock wheels. It had smaller tires on it when I got it. They didn't look right so I up sized them a bit. Looks a little better now.
PDXk5 is offline   Reply With Quote
Old 10-06-2014, 03:25 AM   #24
DEISS
Registered User
 
DEISS's Avatar
 
Join Date: Nov 2010
Location: Big Bear Lake, CA.
Posts: 291
Re: Greetings

Your Blazer is in amazing condition, lots of guys here are in envy, including me, of such a rust free survivor. When you get the chance would you post a pic of the options SPID on the inside of your glove box? Thanks, I'll be following along with your subtle and tasteful modifications, Jack.
DEISS is offline   Reply With Quote
Old 10-11-2014, 10:58 AM   #25
67swb72klb
Registered User
 
67swb72klb's Avatar
 
Join Date: Dec 2010
Location: livingston co.mi
Posts: 2,447
Re: Greetings

yes very nice blazer I like what you are doing with it!
__________________
California 65 GTO---Texas 64 burb 283 ---Oklahoma 67 CST SWB BBW wood bed 327 2004r---New Mexico 72 k10 350 350 auto---Georga 72 short step project
67swb72klb is offline   Reply With Quote
Reply

Bookmarks

Tags
1972, blazer, build, restomod, restoration

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 04:21 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com