The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Suspension

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 10-14-2019, 04:46 PM   #1
C30Seenemall
Registered User
 
Join Date: Sep 2015
Location: Englewood, CO
Posts: 48
Pinion nut won't move.

Hey all...

Trying to replace the front pinion seal on my rear differential.
My p/u is 1975 C30 454 automatic. I'm using a 3/4 drive 1& 1/2 " socket, reducing impact adapter and 1/2" impact wrench. Nut ain't budgin'.
Been using WD40 on it, but I'll bet there's something more effective.
There's no rust but it's been on there for 44 years, so...
I have no heat to apply it, (not sure I want an open flame there anyway).
I tried my 1/2" breaker bar but have not applied major leverage to it yet.
Not sure I have enough room for that.

Maybe I should capitulate, and take it to my professional mechanic.
Thanks in advance for your input and assistance!
"Not-Muscle-Bound" Wayne
C30Seenemall is offline   Reply With Quote
Old 10-14-2019, 06:38 PM   #2
tinydb84
Registered User
 
tinydb84's Avatar
 
Join Date: Jul 2009
Location: San Jose Ca
Posts: 2,871
Re: Pinion nut won't move.

What is your impact rated to? That might be the issue.
__________________
David
Used parts build: http://67-72chevytrucks.com/vboard/s...d.php?t=638991
My brother's Nova: http://www.67-72chevytrucks.com/vboa...d.php?t=727985
Rear suspension rework: http://www.67-72chevytrucks.com/vboa...d.php?t=750557
Instagram: myfabguy
tinydb84 is offline   Reply With Quote
Old 10-14-2019, 07:18 PM   #3
Keith Seymore
Registered User
 
Keith Seymore's Avatar
 
Join Date: May 2009
Location: Motor City
Posts: 9,136
Re: Pinion nut won't move.

Yah - it's got about 10,000 ft-lbs of torque on it, so you are going to want to have plenty of leverage.

K
__________________
Chevrolet Flint Assembly
1979-1986
GM Full Size Truck Engineering
1986 - 2019
Intro from an Old Assembly Guy: http://67-72chevytrucks.com/vboard/s...d.php?t=342926
My Pontiac story: http://forums.maxperformanceinc.com/...d.php?t=560524
Chevelle intro: http://www.superchevy.com/features/s...hevy-chevelle/
Keith Seymore is offline   Reply With Quote
Old 10-14-2019, 08:42 PM   #4
mongocanfly
Post Whore

 
mongocanfly's Avatar
 
Join Date: May 2015
Location: Alabama
Posts: 14,557
Re: Pinion nut won't move.

I used a 3/4" drive ratchet on mine with a 4ft cheater to get mine to break loose
__________________
Mongo...aka Greg

RIP Dad
RIP Jesse

1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598
Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334
Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563
2023 Chevy Z71..daily driver
mongocanfly is offline   Reply With Quote
Old 10-14-2019, 10:13 PM   #5
C30Seenemall
Registered User
 
Join Date: Sep 2015
Location: Englewood, CO
Posts: 48
Re: Pinion nut won't move.

Quote:
Originally Posted by tinydb84 View Post
What is your impact rated to? That might be the issue.
I believe it's about 250 ft lbs of torque.
I will need a lot more - obviously.
Any idea how much more?
I see 1/2 impacts from 950 to 1190 ft lbs., and 3/4 impacts from 1500 to 1700 ft lbs. Should I go whole hog and do the 3/4 impact with 1700 ft lbs?

Thanks!
Wayne
C30Seenemall is offline   Reply With Quote
Old 10-15-2019, 02:24 AM   #6
mongocanfly
Post Whore

 
mongocanfly's Avatar
 
Join Date: May 2015
Location: Alabama
Posts: 14,557
Re: Pinion nut won't move.

good high quality 1/2 drive impact sockets and breaker bar should be ok....but if you have 3/4 drive then that's what id use
__________________
Mongo...aka Greg

RIP Dad
RIP Jesse

1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598
Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334
Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563
2023 Chevy Z71..daily driver
mongocanfly is offline   Reply With Quote
Old 10-15-2019, 07:14 AM   #7
PGSigns
Senior Member
 
PGSigns's Avatar
 
Join Date: Jan 2011
Location: Hayes Va
Posts: 4,569
Re: Pinion nut won't move.

Get a socket the fits your impact so you get rid of the adapters. That will help. Then you have to have something solid to hold the yoke. If it is shaking you are getting very little of the impacts power applied. I have a 36" pipe wrench I use. The blow air from your compressor till it cuts on. Wait for it to cut off then hit the nut. That will give you the most from what you have. Then there is always a bit of heat to get it a little more in the mood to move.
Jimmy
__________________
60 to 66 Chevy and GMC window decals
http://67-72chevytrucks.com/vboard/s...d.php?t=661131
Good friends, good food and a hotrod what else do you need?
1966 BBW long fleet Daily driver
1965 BBW short fleet Sold and going to a good home
1965 Suburban
2003 3500 Duramax
2005 Ultra Classic
PGSigns is offline   Reply With Quote
Old 10-15-2019, 09:32 AM   #8
C30Seenemall
Registered User
 
Join Date: Sep 2015
Location: Englewood, CO
Posts: 48
Talking Re: Pinion nut won't move.

I wanted to say Thanks!, to all those kind souls who replied with good advice.
I'm going to invest in a 1700 ft lb, 3/4 impact air gun and A 15' 3/8" hose.
It is rated at 1500 ft lbs torque but has a bolt break rating of 1700 ft lbs.

I know a breaker bar and 4 ft cheater would work, I don't have the room to use it.
Besides, who knows when I might need the power for another stubborn nut.
Thanks again!
Wayne
C30Seenemall is offline   Reply With Quote
Old 10-15-2019, 10:59 AM   #9
kwmech
Senior Member
 
Join Date: Mar 2003
Location: Colfax-California
Posts: 8,356
Re: Pinion nut won't move.

Pull the nose of the diff out of the housing and clamp the yoke in a vice.

You'll probably have to use a puller to get the yoke off as the factory puts sealer on the splines to prevent leakage. Also have to be careful going back together with the crush sleeve if you are using it over. OR pull the nose out and take it somewhere where they know what they are doing

Last edited by kwmech; 10-15-2019 at 11:05 AM.
kwmech is offline   Reply With Quote
Old 10-15-2019, 11:01 AM   #10
Keith Seymore
Registered User
 
Keith Seymore's Avatar
 
Join Date: May 2009
Location: Motor City
Posts: 9,136
Re: Pinion nut won't move.

It's pretty common to put Loctite on there, too, if it has ever been apart before.

Reminds me of a story: we used to race with a guy named Bobby Joysey. His dad, Bill, was a salty knowledgeable older guy that built Bobby's engines and helped maintain the car.

We were walking through the pit area one time and you could just see Bill's feet sticking out from under the car. He must have been trying to break that pinion nut loose, because you could hear him hollering "...damn red Loctite! DAMN RED LOCTITE!!"

K
__________________
Chevrolet Flint Assembly
1979-1986
GM Full Size Truck Engineering
1986 - 2019
Intro from an Old Assembly Guy: http://67-72chevytrucks.com/vboard/s...d.php?t=342926
My Pontiac story: http://forums.maxperformanceinc.com/...d.php?t=560524
Chevelle intro: http://www.superchevy.com/features/s...hevy-chevelle/
Keith Seymore is offline   Reply With Quote
Old 10-15-2019, 01:04 PM   #11
C30Seenemall
Registered User
 
Join Date: Sep 2015
Location: Englewood, CO
Posts: 48
Re: Pinion nut won't move.

Quote:
Originally Posted by kwmech View Post
Pull the nose of the diff out of the housing and clamp the yoke in a vice.

You'll probably have to use a puller to get the yoke off as the factory puts sealer on the splines to prevent leakage. Also have to be careful going back together with the crush sleeve if you are using it over. OR pull the nose out and take it somewhere where they know what they are doing
By "crush sleeve", you are referring to what the manual calls out as a "Collapsible Spacer", right?
As long as I don't allow the bearing to come out, when I replace the seal and reinstall the yoke, I won't disturb the crush sleeve, correct?

Last edited by C30Seenemall; 10-15-2019 at 01:13 PM.
C30Seenemall is offline   Reply With Quote
Old 10-16-2019, 06:55 AM   #12
PGSigns
Senior Member
 
PGSigns's Avatar
 
Join Date: Jan 2011
Location: Hayes Va
Posts: 4,569
Re: Pinion nut won't move.

The crush sleeve is used to set the bearing preload. As you tighten the nut the crush sleeve will shorten up and keep the space between the bearings set. The process for putting one together with a crush sleeve is to pull the nut down (this where the vice comes in handy) till you feel a bit of resistance on the bearings. Then take an inch pound dial torque wrench and test the rolling resistance of the pinion. Then back in the vice and ad a little more torque to the nut and test again till you get it where it needs to be. I do not use an impact to tighten the nut. It is very easy to to go to far and have way more preload than you need leading to early bearing departure from this world. Here is a quick video on setting the preload.
https://www.youtube.com/watch?v=lD8QNQATrNs
Jimmy
__________________
60 to 66 Chevy and GMC window decals
http://67-72chevytrucks.com/vboard/s...d.php?t=661131
Good friends, good food and a hotrod what else do you need?
1966 BBW long fleet Daily driver
1965 BBW short fleet Sold and going to a good home
1965 Suburban
2003 3500 Duramax
2005 Ultra Classic
PGSigns is offline   Reply With Quote
Old 10-16-2019, 09:27 AM   #13
SunSoaked
Registered User
 
SunSoaked's Avatar
 
Join Date: Dec 2011
Location: Yuma Arizona
Posts: 1,524
Re: Pinion nut won't move.

Bigger breaker bar...
Attached Images
 
SunSoaked is offline   Reply With Quote
Old 10-16-2019, 11:22 AM   #14
Keith Seymore
Registered User
 
Keith Seymore's Avatar
 
Join Date: May 2009
Location: Motor City
Posts: 9,136
Re: Pinion nut won't move.

Quote:
Originally Posted by SunSoaked View Post
Bigger breaker bar...
Fixed it:

Quote:
Originally Posted by Archimedes
"Give me a lever long enough and a fulcrum on which to place it and I shall break your pinion nut loose"
__________________
Chevrolet Flint Assembly
1979-1986
GM Full Size Truck Engineering
1986 - 2019
Intro from an Old Assembly Guy: http://67-72chevytrucks.com/vboard/s...d.php?t=342926
My Pontiac story: http://forums.maxperformanceinc.com/...d.php?t=560524
Chevelle intro: http://www.superchevy.com/features/s...hevy-chevelle/
Keith Seymore is offline   Reply With Quote
Old 10-16-2019, 11:24 AM   #15
Keith Seymore
Registered User
 
Keith Seymore's Avatar
 
Join Date: May 2009
Location: Motor City
Posts: 9,136
Re: Pinion nut won't move.

Also by the same guy:


Quote:
Originally Posted by Archimedes
"Believe not everything which has been read on the Internet."
__________________
Chevrolet Flint Assembly
1979-1986
GM Full Size Truck Engineering
1986 - 2019
Intro from an Old Assembly Guy: http://67-72chevytrucks.com/vboard/s...d.php?t=342926
My Pontiac story: http://forums.maxperformanceinc.com/...d.php?t=560524
Chevelle intro: http://www.superchevy.com/features/s...hevy-chevelle/
Keith Seymore is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:19 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com