The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 04-03-2021, 07:43 PM   #1
Bandit130
Registered User
 
Bandit130's Avatar
 
Join Date: Dec 2014
Location: Euless, Texas
Posts: 510
Runs rough when accelerating

Engine started running rough this last week on accelerating. Runs normal in Park or Neutral while revving. Runs rough in gear sitting still also. Replaced plugs and the in-carb fuel filter today and no difference. Truck died on the street last weekend and I found a vaccuum hose had split on the end and fell off. Trying to restart I flooded carb and could not start for a while. This flooding may have caused an issue in the carb. The last rebuild was July 2017. Thinking I may need to rebuild again, not sure.

Any help is appreciated.
__________________
1974 Cheyenne 10 LWB Stock 350 W/HEI /TH350/AC/4 BBL Quadrajet


Mopar by Birth
Chevy by Choice
Bandit130 is offline   Reply With Quote
Old 04-04-2021, 07:27 AM   #2
4u2nv
Registered User
 
Join Date: Oct 2018
Location: Ontario Peterborough
Posts: 732
Re: Runs rough when accelerating

Maybe check the float ????????
4u2nv is offline   Reply With Quote
Old 04-04-2021, 09:58 AM   #3
Corts60
Just here to tinker
 
Corts60's Avatar
 
Join Date: Jun 2008
Location: Holland, MI
Posts: 3,672
Re: Runs rough when accelerating

Put a vacuum gauge on it and see what you are pulling. If you have a stock-ish cam, you should be at least 16-18" vacuum at idle.

Other than that, you could have a weak fuel pump if fuel isn't keeping up under load.
Corts60 is offline   Reply With Quote
Old 04-04-2021, 05:40 PM   #4
Dead Parrot
Registered User
 
Join Date: Aug 2012
Location: Oklahoma City, OK
Posts: 2,461
Re: Runs rough when accelerating

Check all the suction rubber on the fuel system. Frame to pump. Valve to frame(if dual tank). Tank to valve(or frame if single tank). A hole in one of the hoses can cause the symptoms you have. If one hose was bad, possible others are as well. Also, mice will sometimes nibble on hoses.

A none fuel cause might be a bad distributor cap. There is a carbon button in the top of the cap that does wear out.
Dead Parrot is offline   Reply With Quote
Old 04-04-2021, 06:18 PM   #5
Bandit130
Registered User
 
Bandit130's Avatar
 
Join Date: Dec 2014
Location: Euless, Texas
Posts: 510
Re: Runs rough when accelerating

I have rechecked all vacuum lines, plug wires and all are good. Pulled dist cap and nothing bad found. Checked fuel lines and cannot find anything I can tell that is causing this. Would a bad ignition module cause this or possibly coil? I have had a no start due to the module before.
__________________
1974 Cheyenne 10 LWB Stock 350 W/HEI /TH350/AC/4 BBL Quadrajet


Mopar by Birth
Chevy by Choice
Bandit130 is offline   Reply With Quote
Old 04-04-2021, 06:31 PM   #6
Nick_R_23
Registered User
 
Nick_R_23's Avatar
 
Join Date: May 2016
Location: Willow, Alaska
Posts: 836
Re: Runs rough when accelerating

How have you checked the spark plug wires to determine if they are good? A miss under load is a common effect of an ignition problem. I would recommend replacing the wires, cap, and rotor with quality parts to eliminate that as a potential issue.

I would also take a look at your accelerator pump in the carb, and ensure it is working correctly.
Nick_R_23 is offline   Reply With Quote
Old 04-04-2021, 06:48 PM   #7
truckin 79
Registered User
 
Join Date: Jun 2014
Location: CO
Posts: 727
Re: Runs rough when accelerating

I would say you still have some carbon/junk between needle and seat in carb. Put some carb cleaner through vent tube in carb should clean it up. Just trying to start truck should not cause truck to flood. If carb cleaner does not clear it up then you might have to take carb apart and clean
__________________
79 Chevy 2wd BIG10 350 TH400
truckin 79 is offline   Reply With Quote
Old 04-10-2021, 07:35 PM   #8
Bandit130
Registered User
 
Bandit130's Avatar
 
Join Date: Dec 2014
Location: Euless, Texas
Posts: 510
Re: Runs rough when accelerating

UPDATE

I performed all the troubleshooting I could do with only having a carport and limited tools. Finally decided to take it to my tech and said my cam had finally worn down that is causing the rough running. He had discovered the #8 cam lobe was worn a few years ago when replacing the valve stem seals. It was worn and only raising rocker arm a little. He is in the process replacing cam. He is going to put in an Edelbrock Performer cam. He said it is the beefiest he could install without any other upgrades which is more than the stock one. Should be finished by next Friday.
__________________
1974 Cheyenne 10 LWB Stock 350 W/HEI /TH350/AC/4 BBL Quadrajet


Mopar by Birth
Chevy by Choice
Bandit130 is offline   Reply With Quote
Old 04-10-2021, 09:59 PM   #9
geezer#99
Registered User
 
geezer#99's Avatar
 
Join Date: Aug 2009
Location: Bowser
Posts: 13,494
Re: Runs rough when accelerating

Considering all the fine metal dispersed inside your motor, a cam change is a waste of money.
There’s only one cure.
Complete tear down and cleaning.
geezer#99 is online now   Reply With Quote
Old 04-10-2021, 10:18 PM   #10
Bandit130
Registered User
 
Bandit130's Avatar
 
Join Date: Dec 2014
Location: Euless, Texas
Posts: 510
Re: Runs rough when accelerating

I got the truck in 2015 and it has apparently been wearing slowly over the years so I think the metal has gone thru the filter and out with the regular oil changes that have been done since I have had it. I think it will be ok. Shall see.
__________________
1974 Cheyenne 10 LWB Stock 350 W/HEI /TH350/AC/4 BBL Quadrajet


Mopar by Birth
Chevy by Choice
Bandit130 is offline   Reply With Quote
Old 04-11-2021, 12:04 AM   #11
geezer#99
Registered User
 
geezer#99's Avatar
 
Join Date: Aug 2009
Location: Bowser
Posts: 13,494
Re: Runs rough when accelerating

Ya!
It’s only money!
geezer#99 is online now   Reply With Quote
Old 04-11-2021, 12:05 AM   #12
Nick_R_23
Registered User
 
Nick_R_23's Avatar
 
Join Date: May 2016
Location: Willow, Alaska
Posts: 836
Re: Runs rough when accelerating

I wouldn't take the chance on it. That metal tends to hide in the journals of the cam bearings and internal oil passage plugs. With todays detergent oils, it's likely those metal shavings can become dislodged and find their way around. Cams wipe lobes quickly and then work harden, so this isn't an issue that has been going on for years.
Nick_R_23 is offline   Reply With Quote
Old 04-12-2021, 09:11 AM   #13
cadillac_al
Registered User
 
Join Date: Oct 2013
Location: Maine
Posts: 2,325
Re: Runs rough when accelerating

I can't even count the number of worn 305/350 cams I have replaced without tearing down the engine. The shop I used to hang out at in the 70's used to just remove and replace them too. The oil filter must work. A full tear down is always better if you have the time and money for the peace of mind. If it's just an old truck, send it. MY 76 K15 is on it's 3rd cam at 180k miles.
__________________
76 Chevy K20
76 GMC K15
77 Chevy C10
77 Chevy K10
cadillac_al is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:07 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com