|
11-26-2022, 01:25 PM
|
#326 | ||
|
Senior Member
 
Join Date: May 2007
Location: Doodah Kansas
Posts: 7,747
|
Re: Francis the Tow Pig - 1949 GMC 250 Dually
Quote:
woooop that looks pretty great! Quote:
I noticed you had to go 3/5ths instead of the 1/4 I said, but did you taper the end?  looks great man!
__________________
the mass of men live lives of quiet desperation if there is a problem, I can have it. new project WAYNE http://67-72chevytrucks.com/vboard/s...d.php?t=844393 |
||
|
|
|
11-26-2022, 01:42 PM
|
#327 | |
|
Registered User
Join Date: Aug 2012
Location: Northeast KS
Posts: 1,775
|
Re: Francis the Tow Pig - 1949 GMC 250 Dually
Quote:
Thanks, Russ! I didn't taper the end, trying to keep the heat down on the coil. I figured with my 600+ lbs over an ECSB V6 rig, the 1/4 wasn't going to be enough.
__________________
1999 GMC Suburban K2500 SLT, 454/4L80E 1991 Z/28, 6.0L/T56 1949 GMC 250, S10 Frame, 6.0L/4L80E Instagram @aceshighspeedshop |
|
|
|
|
|
11-26-2022, 02:16 PM
|
#328 | |
|
Senior Member
Join Date: May 2007
Location: Doodah Kansas
Posts: 7,747
|
Re: Francis the Tow Pig - 1949 GMC 250 Dually
Quote:
haha the taper adds the extra! the original coil is flattened on the end but when you cut off the 1/4 it is at like a 60 degree angle to the pocket, tapering lowers it that little bit and in my opinion helps it fit the pocket. so potato potatto, same diff! more than one way to skin an apple.
__________________
the mass of men live lives of quiet desperation if there is a problem, I can have it. new project WAYNE http://67-72chevytrucks.com/vboard/s...d.php?t=844393 |
|
|
|
|
|
11-28-2022, 10:16 AM
|
#329 |
|
Registered User
Join Date: Aug 2012
Location: Northeast KS
Posts: 1,775
|
Re: Francis the Tow Pig - 1949 GMC 250 Dually
When I first built the truck back in 2017, I had to remove the carrier bearing cross member when I went to a 1-piece driveshaft. Decided it was time to replace it with something to help tie the frame together a little better, and at the same time reduce some flex.
Started with some angle for the frame brackets:  Tubing cut to length and ready to be tacked in place:  Melting it all together:  [ Painted up and installed:   With it being mounted below the frame, it clears the exhaust and driveshaft with plenty of room to spare. With the 1" height, it also remains above the lowest point on the pickup. 
__________________
1999 GMC Suburban K2500 SLT, 454/4L80E 1991 Z/28, 6.0L/T56 1949 GMC 250, S10 Frame, 6.0L/4L80E Instagram @aceshighspeedshop Last edited by OutlawDrifter; 11-28-2022 at 12:51 PM. |
|
|
|
|
11-29-2022, 09:15 AM
|
#330 |
|
Senior Member
Join Date: May 2007
Location: Doodah Kansas
Posts: 7,747
|
Re: Francis the Tow Pig - 1949 GMC 250 Dually
nice work, very strong!
__________________
the mass of men live lives of quiet desperation if there is a problem, I can have it. new project WAYNE http://67-72chevytrucks.com/vboard/s...d.php?t=844393 |
|
|
|
|
11-29-2022, 09:50 AM
|
#331 | |
|
Registered User
Join Date: Aug 2012
Location: Northeast KS
Posts: 1,775
|
Re: Francis the Tow Pig - 1949 GMC 250 Dually
Quote:
__________________
1999 GMC Suburban K2500 SLT, 454/4L80E 1991 Z/28, 6.0L/T56 1949 GMC 250, S10 Frame, 6.0L/4L80E Instagram @aceshighspeedshop |
|
|
|
|
|
12-02-2022, 07:46 PM
|
#332 |
|
Senior Member
Join Date: May 2007
Location: Doodah Kansas
Posts: 7,747
|
Re: Francis the Tow Pig - 1949 GMC 250 Dually
you can jack it up on that!
__________________
the mass of men live lives of quiet desperation if there is a problem, I can have it. new project WAYNE http://67-72chevytrucks.com/vboard/s...d.php?t=844393 |
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
