Driveshaft length change when swapping to 5-lug? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

D-n-Tyke · 07-10-2023, 03:13 AM

For those of you that have done the C20 8-lug to 5-lug conversion by swapping in a rearend out of a C10, did you have to have your driveshaft remade? Specifically those with 2-piece driveshafts. Or did your original driveshaft bolt right back up?

I swapped out the rear end in my 1969 Suburban with ine out of a 1971 C10. I am trying to figure out the rear section of my 2-piece shaft will work as is. I also did a LS/4L80 swap so can't just bolt mine up and check.

**special-K** · 07-10-2023, 06:27 AM

I've done the opposite on an '85 Jimmy and it took a shorter driveshaft going to a 14-bolt rear. I also lifted it 4", so that ended up compensating perfectly. Was able to run driveshaft as is with conversion u-joint. I think you'll need a longer driveshaft

xs-cash · 07-10-2023, 06:25 PM

Had to get the rear driveshaft shortened if I remember right , I did this swap bout 20 yrs ago, still in the truck today, it changed the truck dramatically! All for the better

07-10-2023, 03:13 AM	#1
D-n-Tyke Registered User Join Date: Aug 2016 Location: El Cajon, CA Posts: 249	Driveshaft length change when swapping to 5-lug? For those of you that have done the C20 8-lug to 5-lug conversion by swapping in a rearend out of a C10, did you have to have your driveshaft remade? Specifically those with 2-piece driveshafts. Or did your original driveshaft bolt right back up? I swapped out the rear end in my 1969 Suburban with ine out of a 1971 C10. I am trying to figure out the rear section of my 2-piece shaft will work as is. I also did a LS/4L80 swap so can't just bolt mine up and check.

07-10-2023, 06:27 AM	#2
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,863	Re: Driveshaft length change when swapping to 5-lug? I've done the opposite on an '85 Jimmy and it took a shorter driveshaft going to a 14-bolt rear. I also lifted it 4", so that ended up compensating perfectly. Was able to run driveshaft as is with conversion u-joint. I think you'll need a longer driveshaft __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

07-10-2023, 06:25 PM	#3
xs-cash Registered User Join Date: Aug 2017 Location: Edmonton Alberta Canada Posts: 102	Re: Driveshaft length change when swapping to 5-lug? Had to get the rear driveshaft shortened if I remember right , I did this swap bout 20 yrs ago, still in the truck today, it changed the truck dramatically! All for the better



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.