Re: 69 stepside RHD built
Cool build! Steppers are getting popular!
|
Re: 69 stepside RHD built
4 Attachment(s)
After blasting stepper bed, here is progression to reshape and repair rust. For marking hole at rear fender, Lucky to me that can find original fender purpose to measuring position for install rear side marker.
|
Re: 69 stepside RHD built
4 Attachment(s)
Tailgate repair lower part by section renew and replace with new section from zinc sheet plate as same as original sizing. I have had design bushing of tailgate pivot by machine bushing made from brass and round shape bottom of tighten bolt. Brass bushing of both side can be reduced friction of bolt if tighten over limit.
|
Re: 69 stepside RHD built
Very nice work!;)
|
Re: 69 stepside RHD built
3 Attachment(s)
Just impressed when stepper bed was fit on chassis. Due to raining season in our country I will hurry next step painting to reduce occasional of new rust on repaired bed surface.
|
Re: 69 stepside RHD built
2 Attachment(s)
Some progression both left and right rear fender.
|
Re: 69 stepside RHD built
Welcome, and I have so much respect for you guys outside of these United States because it must be so hard to find parts for these trucks, here you can't throw a rock without hitting one, ha ha
keep grindin' (oh and too bad about the stepside I love them things) |
Re: 69 stepside RHD built
Quote:
|
Re: 69 stepside RHD built
Finished paint stepper bed and install on chassis. Change rear axle from 8 lugs to 5 lugs GM 12 bolt from first project that I kept for this project. Temporary wheel from W-work 265/35R18 in rear axle.
|
Re: 69 stepside RHD built
4 Attachment(s)
Work progression pictures.
|
Re: 69 stepside RHD built
Very nice results!!! Nice color too.
|
Re: 69 stepside RHD built
Great progress. The color looks nice.
|
Re: 69 stepside RHD built
Suay mak.
Keep up the good work. You don't see those trucks much at all there. I see what looks like a 60-66 peeking out from under cover. Choke Dee from Burriram. |
Re: 69 stepside RHD built
Great looking Work!
|
Re: 69 stepside RHD built
Kindly accept my sincere appreciation for all guys generous compliments.
|
Re: 69 stepside RHD built
5 Attachment(s)
For front suspension my C10, I was redesign of both upper and lower control arm from local parts from idea picture below. I made new bush housing and machine new shaft of both upper and lower control arm. Then I can use bushing from local parts that I was selected for apply to all control arms.
|
Re: 69 stepside RHD built
5 Attachment(s)
I ordered instruments gauge cluster brand intellitronix model type AP-6003 and bought chrome dash bezel. I think this gauge cluster can be apply for reading engine RPM, speed MPH, volt, fuel level, temperature and oil pressure from LT-1. I bought billet tilt column as well but some think mistaken, I never study how much of length tilt column before ordered. This tilt column too short and I will find the way for apply its to mine stepper. Used lecarra steering wheel look suitable for this tilt column.
https://www.intellitronix.com/produc...k-67-72-analog |
Re: 69 stepside RHD built
5 Attachment(s)
Assembling of all prepared suspension of both front and rear parts. Rear stabilizer bar was installed as many thread had install it.(copy idea ) I can find unused parts in garage apply it to both rear trailing arms. Front suspension with disc brake conversion to 5 lugs.
|
Re: 69 stepside RHD built
Very nice work and great commitment. I'm sure you will have a crowd pleaser when you get done!
Good luck, Rg |
Re: 69 stepside RHD built
Quote:
I will do my best to keep up the good work. |
Re: 69 stepside RHD built
4 Attachment(s)
Today is processing of wiring engine diagram for my truck. Not finish today and will carry on next week again.
|
All times are GMT -4. The time now is 12:43 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com