Re: My '67 Fleetside C10 renew
Jump right in. Don't look back.
You gottz skillz to blow some paint on it. Do it! :bann: |
Re: My '67 Fleetside C10 renew
3 Attachment(s)
I did stuff again! :metal: (with shoes on)
That Van Sickle finished out SWEET! (takes three hot cycles with a fingernail brush to get it off your skin and toenails) I got all those parts hung up and the fun-dome cleaned out. Sanded the sags out of the hood and gave that and the tail gate a good scuff and clean. Laid down a couple fat coats of G2 and will knock that down with 150 and re-coat tomorrow. Smells good in the shop again! |
Re: My '67 Fleetside C10 renew
And your journey begins.... you got this beat already. Give 'er hell!
|
Re: My '67 Fleetside C10 renew
3 Attachment(s)
Snakes 10 - Johnny 22 FINAL
Third time's a charm right? I made the same mistake on the hood as I did in the cab the first time I shot the G2. I layed down perfect, heavy orange-peel on a perfect panel. That was fun to sand for no reason. Snakes 7. I rallied and 150 blocked the hood and gate followed by a good scuff round the edges. Johnny 14. They look awesome!!! Johnny 22 (went for 2 and got it for no reason). Not enough thinner to spray another round. Snakes 10. Johnny takes a knee and takes a HUGE pull of elephant jerky. That tail gate is only gettin one more lick. I'd say the same about the hood but I'm almost sure the OCD is gonna kick in and it'll take more. Knuckle-Head sold that close ratio Muncie for $500.00 Folded like a cheap suitcase. He's got his motor to long block now and will be scoring the S10 mounts and headers, intake and some accessories. |
Re: My '67 Fleetside C10 renew
1 Attachment(s)
Started as a used two-bolt 350 +0.030 He had it tanked, fluxed, honed, decked, cam bearings and crank polish. Summit re-ring kit. After he got the bottom end put together we found that it had them "rebuilder" pistons, which are -.025 compression height. I tried to talk him into pistons but he's on the cheap. I gave him some smoggy 882 heads with 194's and he put them sissy 0.015 head gaskets on there for 8.9:1. He cleaned up the valves and re-assembled with new seals and scored a miled Lunati cam and lifters. I have a nice donor Q-jet and he's got the GM intake pictured, which I think would be perfect from like 500-5500 but NOOOOO he's after a 8000 RPM single-plane and that little 600CFM Holley of mine he's got sitting on there. I'm sure it'll ROCK in any configuration in that little pickup with the Lincoln Locker :metal:
He'll be OFF my insurance soon. |
Re: My '67 Fleetside C10 renew
Ha, oughta be a runnin' lil' truck! Finish yours and whip him, Dad!
|
Re: My '67 Fleetside C10 renew
Gettin there... High 5's all around.
|
Re: My '67 Fleetside C10 renew
Parts are looking Great Man! Don't sweat the paint job, you've got this under control.:chevy::chevy::chevy:
|
Re: My '67 Fleetside C10 renew
Weekend came and went and NO work on the truck. We did get out for an awesome ride tho! Last night I shot more hi-build on the hood and tail gate followed with a guide coat. I decided to take today off and I'm going out there to block those parts out and get to scuffin on my doors and fenders :metal:
For some damn reason I can't upload photos??? Security token??? I've got some nice shots from our ride and hope to upload some body panel shots tonight. Hope this tube link works... https://www.youtube.com/watch?v=vjo9SxaPdZA |
Re: My '67 Fleetside C10 renew
Quote:
Beautiful view by the way... |
Re: My '67 Fleetside C10 renew
Same here.
Weekend came and went. Had to work Saturday 4am-10am. 45 min drive to work. Got stuck mowing grass. Sunday,inlaws,dinner, no shop time. Gotta a really cool Fathers Day card though.:metal: I feel your no shop time pain.http://www.clicksmilies.com/s1106/tr...smiley-043.gif |
Re: My '67 Fleetside C10 renew
Well I didn't go to work yesterday. The PLAN was to work on the TRUCK. I got out there and got the hood pretty well blocked then RINGGGG RINGGGG....
My daughter is broke down on the highway. Me, the Boy and a chain head out to the rescue. Turns out her Subaru lost a timing belt and I spent the rest of the day doing that only to find out it's an interference engine and we got bent valves folks. Looks like I'll be tied up on NOT THE TRUCK here for another short spell. |
Re: My '67 Fleetside C10 renew
Gaaaaah. At least you were home to go get her. How bad was that tear down?
Posted via Mobile Device |
Re: My '67 Fleetside C10 renew
It was too damn easy. We cracked it open, ran to Napa for the $35 belt and had it back together, all in 4 or 5 hours. Only wish we had done that BEFORE it let go. Dammit! The second hole we tested for compression was zero and thats when we dropped the tools. Still gotta check the other two and hopefully it's just one head that needs peeled off. Sure hope the pistons are OK.
|
Re: My '67 Fleetside C10 renew
I sure wish I had sheetmetal that looked like yours
Posted via Mobile Device |
Re: My '67 Fleetside C10 renew
3 Attachment(s)
I was pretty lucky to find such a solid truck and this forum! I can't wait to get back on the mechanicals.
Yesterday after work I got the Subaru back in the shop and finished the compression test. Luckily, both holes on the driver's side were better than 150psi and holding so I ripped the passenger side off. It was much smoother than you'd imagine. The only cussin I did was when we were pushing the thing into the shop! I gotta get some more gravel out in front of the door so it's not such a step up onto the slab! Sure-e-nuff, all the intakes on that head are dinked. I'll be dropping that off today for a basic valve job and checked for flatness. The Boy got his dizzy built the day before and kitted a Holley I gave him last night. |
Re: My '67 Fleetside C10 renew
Hmmm..... Dodgin' the bodywork.... Noted. Lol!
Posted via Mobile Device |
Re: My '67 Fleetside C10 renew
5 Attachment(s)
Yesssss the picture upload thing is working again! Here's those riding shots from last weekend. In the fourth picture you can see the rock face WAAAY across the valley. That's where the first three shots were from and where we shot the video. Would like to go out again this weekend but it's looking pretty busy :(
|
Re: My '67 Fleetside C10 renew
3 Attachment(s)
The last shot is looking the other direction, towards my house.
|
Re: My '67 Fleetside C10 renew
Quote:
|
Re: My '67 Fleetside C10 renew
Beautiful country! I'm usually too busy trying to kill myself too look around. Looks like fun! We're takin a trip in the next couple weeks.
Posted via Mobile Device |
Re: My '67 Fleetside C10 renew
Subscribed. Killer thread!!! Keep it up! :metal:
|
Re: My '67 Fleetside C10 renew
Quote:
I did stuff this weekend. Got the s-hole cleaned up and all the Subaru guts in a heap. Finished blocking the hood and tail gate and shot another thin coat. I'll wetsand P400 and HOPEFULLY can spring for some PAINT :metal: |
Re: My '67 Fleetside C10 renew
Check out that Southern Polyurethanes paint. Good Stuff, Cheap! Search the Silver Dollar thread.
|
Re: My '67 Fleetside C10 renew
Looks like maybe a cr125 and an rm of some sort. Looks fun I miss my yzf450
Posted via Mobile Device |
All times are GMT -4. The time now is 03:46 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com