Re: Project "lighten it up" including Scott's IFS install
Well now with it all together, motor plate and limiters instead of motor mounts and inner frame supports, fluids in and air cleaner on I put it on the scales for a final weight of 3745. More I thought about it from last weigh in I did need to add a couple jugs of anti freeze plus 7qts of oil and 4AWG wire front to back to redo my alternator proper, vac pump plumbing, anyway it all added up fast.
I'm still happy with a 210lb reduction as 200 was my happy goal with 150 being my expectation for the project, leaning more towards a aluminum block once again LOL. |
Re: Project "lighten it up" including Scott's IFS install
When are you to get to the track?
|
Re: Project "lighten it up" including Scott's IFS install
Quote:
http://www.67-72chevytrucks.com/vboa...d.php?t=632568 |
Re: Project "lighten it up" including Scott's IFS install
Repaired the truck, loaded it up headed to the track agin this weekend for points races, blew a trailer tire in the rain on the way in, got rained out. Bought a new tire so I'd have a spare again, stayed overnight and got rained out today also, headed home and unloaded it.
Another crappy weekend of non racing. |
Re: Project "lighten it up" including Scott's IFS install
KOOL truck!!! is that hood custom? Or did you add the cowl?
loosing weight can get expensive. i did that on my Hotrod |
Re: Project "lighten it up" including Scott's IFS install
It's a Harwood fiberglass show hood.
|
Re: Project "lighten it up" including Scott's IFS install
Mother Nature can suck at times! She doesn't seem like a drag racing fan lately!
|
Re: Project "lighten it up" including Scott's IFS install
I bet there is around 80 to 100 lbs in the radiator support and fender wells. is the heater still in the truck? by the way i love those wheels..
|
Re: Project "lighten it up" including Scott's IFS install
Hey sailplane, where the hell you been?
Heater is long gone, still debating the inners, but not sure, just got back from a weekend of racing and sticky gravel from tires with traction compound everywhere, not sure if I'm into picking them off the intake. Might give it a try some weekend and see how bad it is. |
Re: Project "lighten it up" including Scott's IFS install
I wish someone made a set of carbon fiber inner fenders for our trucks. It gets so nasty under the hood when running without inners.
|
Re: Project "lighten it up" including Scott's IFS install
well,
i have been working and paying bills. the wife is long graduated and the boys out of school also and has a good job. i took on the crazy project of rebuilding a fishing boat and its done now, i got to enjoy the heck out of it this spring. with the heat on now fish are not biting so i started cleaning the garage and am thinking of starting back on the old beater.. so hopefully i can stay interested in it and get with it. love the front end. one question i have is what stops the the arms when the tires are hanging. is it the shocks or is there some sort of stop? the qa1s i have say not to let them be the limeter. so i need to figure this out before i go much further. anyways love the set up.. did you get here to hook right the first time out? later andrew K |
Re: Project "lighten it up" including Scott's IFS install
They just hang on the shocks, I run AFCOs on the front not sure if they say not to use them as a limiter or not, I now went with a set of Strange doubles for the back and got rid of my QA1s. Running Hypercoil springs also on all four corners now.
I was racing it before the front and it hooked, I'm now tuning the new back shocks and springs, plus new size tires that are pure slicks vs DOTs I have always used, best 60' so far is a 1.39, might be a bit more in it with the 180 shot. Just plan on setting it up to run the low 10s for now. On a side note after I busted my pinion yoke last time out, I replaced all the universals when out and looked the shaft over, but must have been a hairline crack around the weld on the tube I missed or couldn't see, first launch of the weekenf I pealed it clean off. Was able to be a shaft built and got it back in to make eliminations, no qualifying runs at all, threw a 10.25 on the window and ran a 10.28, but I slept so bad on the light that I could not run the slower guy down. |
Re: Project "lighten it up" including Scott's IFS install
Quote:
|
Re: Project "lighten it up" including Scott's IFS install
I know my exhaust is heavy but like running an exhaust, I'm going to a custom aluminum exhaust, I bet it will shave off 50lbs right there, also eventually going to an aluminum block, another 150lbs there.
Downside is I'm going to go to a 8.50 cert cage, and a anti roll bar in the back so adding weight in return. Might lose the inner fenders all together, even though not to keen on the extra under hood dirt that will add, so maybe glass is a better route for me. |
Re: Project "lighten it up" including Scott's IFS install
Aluminum driveshaft is another option. .
|
Re: Project "lighten it up" including Scott's IFS install
i am realy thinking of mounting my radiator to the back bars of my cage. you no the ones that go down from the main hoop to the back of the frame, the radiator would set inside the box of the truck with some duct work runing to the ground so air would flow from under the truck and up. to do this i thought of using aluminum tubing run on the inside of the frame. so there would be no radiator or support up front. and the weight would be right in front of the rear tires. just don't no if this would be a legality issue or a heat issue. of course i would have to run fenderwell headers.
anyways just idea at the extreme. later Andrew K |
Re: Project "lighten it up" including Scott's IFS install
Serious mud trucks run that type of setup.
|
Re: Project "lighten it up" including Scott's IFS install
2 Attachment(s)
Quote:
|
Re: Project "lighten it up" including Scott's IFS install
I decided against the rear radiator. as the tubes going back will add more weight..
im going to run 1 piece side glass using lexan. might be pricey though cause 1 piece dosnt make them in lexan so i might have to buy the kit then buy the lexan.. |
Re: Project "lighten it up" including Scott's IFS install
Let us know how it turns out.
|
Re: Project "lighten it up" including Scott's IFS install
I have the same cam in a .030 over 427,with SRP 12-1 pistons,and Dart Pro 1 heads,310 cc,Vic jr intake and an 850 Holley hp carb,will let you know how mine works when complete, I hope it works as well as yours
|
Re: Project "lighten it up" including Scott's IFS install
Just an update from summer never got around to posting, inner fenders are gone and pulled the exhaust, but rest of planned upgrades were put on hold as I tore my rotator and had to have surgery on it in the summer so my season was ended before it really started.
http://i15.photobucket.com/albums/a3...pse2olpje8.jpg http://i15.photobucket.com/albums/a3...pszdp1opx9.jpg |
Re: Project "lighten it up" including Scott's IFS install
I hate to here about you having surgery. Have you scaled the truck since the upgrades? I would make a core support you could definable save wait there.
|
All times are GMT -4. The time now is 09:38 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com