The 1947 - Present Chevrolet & GMC Truck Message Board Network

Page 3 of 3

Show 40 post(s) from this thread on one page

The 1947 - Present Chevrolet & GMC Truck Message Board Network (https://67-72chevytrucks.com/vboard/index.php)

- Suspension Marketplace (https://67-72chevytrucks.com/vboard/forumdisplay.php?f=210)

- - 13" and 14" Corvette Brakes for C10's (https://67-72chevytrucks.com/vboard/showthread.php?t=465140)

slimneverdies

08-31-2014 02:11 AM

Re: 13" and 14" Corvette Brakes for C10's

Quote:

Originally Posted by skorpioskorpio (Post 6823799)

The rotors come drilled with the bolt pattern of the hubs, so 'Vette rotors are drilled for 5x4.75, any other bolt pattern requires the center to be drilled for the new bolt pattern. I suppose you wouldn't need to redrill if it's a 2 piece modular rotor, though when I looked at those for my application they were triple the price, again new hubs would be cheaper. Kore3 did custom milled hubs for me for way less than a set of 2 piece rotors with caps, bearings and seals and anodized. Not to say my brakes were cheap they weren't not by any measure, but they are cheap to maintain, for 13.5"F/13"R brakes and have integrated parking drums.

These are the type rotors I have, DBA T3 one piece:
http://www.dbausa.com/wp-content/upl...1/CLUB_021.jpg
Either side slotted, no holes.

I have z06 rotors which are 14" but I would like the 15" rotors. They seem to only come in the 6 lug for the later model Chevy trucks

dkauffman05

10-06-2014 09:00 PM

Re: 13" and 14" Corvette Brakes for C10's

Anything g ever come of the camaro or cts calipers on a cpp modular spindle ? Or what's the cheapes route to make them happen ? I plan on running 18" wheels.

DC43	10-07-2014 02:22 AM

Re: 13" and 14" Corvette Brakes for C10's

Are you still offering the kits? do you have a rear kit available? Pm me prices for a 5x4.75 if you still are. Thanks

chase@ridetech

10-28-2014 02:53 PM

Re: 13" and 14" Corvette Brakes for C10's

I may have missed it, but do these work with our Ridetech modular C-10 Spindles?

skorpioskorpio

10-28-2014 04:14 PM

Re: 13" and 14" Corvette Brakes for C10's

2 Attachment(s)

This is my setup for the CPP modular with the Z51 PBR sliders for 13 1/2" rotors. It required spot machining the spindles as the CPP spindles are only faced on one side and my dual sandwiched bracket and spacer setup needed flat parallel surfaces on both sides. A lot of this has to do with the increased offset distance my custom hubs and pin mount adapters needed. It pushed the caliper too far out from the spindle to deal with with spacers on brackets on one side only. I was worried I would introduce a lot of caliper shudder if not outright failure of the casting. These were custom made for me (along with custom milled hubs) by Kore3. Oh and they do clear an 18" wheel, well mine anyway, but only by about 1/8th of an inch.
Attachment 1317535
Attachment 1317536

raic65

10-28-2014 05:16 PM

Re: 13" and 14" Corvette Brakes for C10's

Quote:

Originally Posted by dkauffman05 (Post 6869760)

Anything g ever come of the camaro or cts calipers on a cpp modular spindle ? Or what's the cheapes route to make them happen ? I plan on running 18" wheels.

I made a set of brackets for my setup. See post 5. I believe John Glenn (astronaut) is doing the same with his C10.

http://67-72chevytrucks.com/vboard/s...22#post5891322

slammed48

05-06-2015 08:54 PM

Re: 13" and 14" Corvette Brakes for C10's

What do you suggest using in the rear with this front set up?

Also, have you tried putting these on a Belltech dropped spindle?

skorpioskorpio

05-07-2015 05:38 AM

Re: 13" and 14" Corvette Brakes for C10's

1 Attachment(s)

This is my rear setup 13" (Also from a Z51 'Vette) with integrated parking brake drums inside the rotor hat.

ranger2339

12-06-2015 08:46 PM

Re: 13" and 14" Corvette Brakes for C10's

Are these kits sill available?

G8DAN

02-27-2016 05:29 PM

Re: 13" and 14" Corvette Brakes for C10's

Bump. Are the kits still available? I may be interested in one within the next few weeks.

G8DAN

03-30-2016 08:52 PM

Re: 13" and 14" Corvette Brakes for C10's

Would you still be open to having us send you the CTSV rotors and calipers for designing of the bracket?

chevyschevy

11-01-2018 10:38 AM

Re: 13" and 14" Corvette Brakes for C10's

Anyone know if these are still available?
Looking to buy now.

way2lo2

11-01-2018 10:48 AM

Re: 13" and 14" Corvette Brakes for C10's

Quote:

Originally Posted by chevyschevy (Post 8375767)

Anyone know if these are still available?
Looking to buy now.

yes sir

chevyschevy

11-01-2018 10:59 AM

Re: 13" and 14" Corvette Brakes for C10's

PM sent

ChuckLee

01-12-2019 03:22 PM

Re: 13" and 14" Corvette Brakes for C10's

Email sent. This looks like a no-brainer.

siggyfreud

03-17-2019 11:56 PM

Re: 13" and 14" Corvette Brakes for C10's

Still selling these? I PM'ed you a few weeks back but haven't seen anything.

EVRLET

03-18-2019 01:14 AM

Re: 13" and 14" Corvette Brakes for C10's

Kore3 also specializes in Corvette brakes. I have the Z06 front and rear on my 67.

siggyfreud

03-18-2019 07:25 PM

Re: 13" and 14" Corvette Brakes for C10's

I got a reply to my PM, and have responded. Looks like they're still selling them, just have gone a little quiet on the thread perhaps.

All times are GMT -4. The time now is 05:08 AM.

Page 3 of 3

Show 40 post(s) from this thread on one page