|
Re: My new project 86 Silverado
1 Attachment(s)
engine as it is at the moment
|
Re: My new project 86 Silverado
Russell pump to carb line came in... manual master cylinder and push rod otw...
|
Re: My new project 86 Silverado
1 Attachment(s)
Pass fender on
|
Re: My new project 86 Silverado
i should probably start a thread for this. but... just a shoutout basically...
i have a whole bunch of stuff from my build that i'm not going to use because i replaced it. i'll list them so you know what i have in a couple days. I'm not looking to sell anything, would rather trade , or give away so i can finish up my build. |
Re: My new project 86 Silverado
1 Attachment(s)
Found a manual master cylinder that comes with a pushrod...
It is a Dorman M98952 39 bucks at the usual place online |
Re: My new project 86 Silverado
1 Attachment(s)
alternator bracket on the way...
|
Re: My new project 86 Silverado
Fuel hose, adel clamps came in so I can finish installing the fuel system
my crimpers and heat shrink tubing came in, getting ready to wire the truck finally... i think i may have to go with 16 inch wheels. the 2 1/2 drop spindles have the lower control arm lip really close to the rims on the 15's... i'll know more when i loosen the cross arm nuts etc. and get the suspension settled. i hope i don't have to change wheels... |
Re: My new project 86 Silverado
1 Attachment(s)
Got master cylinder installed, have to drill a hole about 1 1/2 inches above the factory Clevis pin location on the brake pedal to get the right ratio for manual brakes
|
Re: My new project 86 Silverado
1 Attachment(s)
ignition panel on the way...
|
Re: My new project 86 Silverado
got my ignition panel, and alt brackets in! universal turn signal switch came in too, will be installing parts for a few days
|
Re: My new project 86 Silverado
got the new stainless transmission lines installed today!
i know, its going slow,slow,slow... |
Re: My new project 86 Silverado
Quote:
|
Re: My new project 86 Silverado
Quote:
|
Re: My new project 86 Silverado
1 Attachment(s)
Finally... get to start on this!!!
|
Re: My new project 86 Silverado
sorry for the long absence, things have picked up, parts ordered... first order of business will be the windshield. updates soon!
|
Re: My new project 86 Silverado
lots of parts on hand
life happens but have leveled off... am i ever going to finish???? smh:confused: |
Re: My new project 86 Silverado
Quote:
|
Re: My new project 86 Silverado
i know, long time no updates
welded up the spot weld holes in the windshield track, primed and sanded around both front back glass openings windshield and back glass is getting installed on the 23rd! |
Re: My new project 86 Silverado
2 Attachment(s)
Glass installed finally!
purchased the rubber from steele rubber in denver, NC |
Re: My new project 86 Silverado
Sorry for the long delay guys
Been a hell of a year I’m back on it Posted via Mobile Device |
Re: My new project 86 Silverado
1 Attachment(s)
New headers arrived
Waiting on my champion 3 row radiator Part num cc716 |
Re: My new project 86 Silverado
1 Attachment(s)
Ordered a Boyd welding fuel tank
I have 2 new saddle tanks and brackets I’ll be selling if anyone is interested |
Re: My new project 86 Silverado
Received my champion radiator
Cc716 |
Re: My new project 86 Silverado
Going to oil prime the engine today, get the valves adjusted on covers on
Install the water pump and thermostat housing Hoping to get the engine installed this weekend 🙏 |
Re: My new project 86 Silverado
Got the oil filter adapter on, new filter, dumped 6 quarts zr1 in.
Primed, 60psi oil pressure with just the drill. Oil everywhere |
| All times are GMT -4. The time now is 02:27 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com