Re: Working Man's Burbon
Not an issue for us natives of the PNW haha!
|
Re: Working Man's Burbon
Quote:
|
Re: Working Man's Burbon
Quote:
And on a different subject what is this thing "AC" everyone is always carrying on about? |
Re: Working Man's Burbon
Hmm, I believe this months truck of the month is green .. know anyone with driving something green? =)
|
Re: Working Man's Burbon
Quote:
Or did you mean A/C [air conditioning]? I don't have it. Not equipped on my '68 Stepside, which must've been a fleet truck. All manual, no frills. My '71 Jimmy was a Deluxe trim model: chrome-ringed windshield, chrome bumpers, chromed shift sticks, vinyl side panels in back, carpet, full gauge dash, and A/C [which was INOP when I bought it.] I took all the A/C parts off when I first got the Truck, and since have lost the bucket they were in. So it would cost a bunch to reinstall Air. A friend who has a Blazer himself, tells me in this climate, you won't feel the cold much even at full blast, the Blazer cabin being too big for factory air to be effective. Maybe it was more effective with R13, IDK. Around here A/C is for sissies. I don't like the HP loss. I used to have a bumper sticker -- THANK GOD FOR THE HEAT/ OR THE SNOWBIRDS WOULD BE HERE ALL YEAR LONG But after 2 decades of solar exposure, it's burned off. |
Re: Working Man's Burbon
1 Attachment(s)
HOT SUBURBAN SIGHTING!
Hot enough to melt snow and ice! |
Re: Working Man's Burbon
Quote:
What did you do catch it on fire? That's a big area compared to the other vehicles.... :) LockDoc |
Re: Working Man's Burbon
Okay you caught me. The real story is after it stopped snowing the wind started blowing. It blew a steady 10 -12 mph with gusts to 22. And due to a strange combination of wind direction, topography and the office building, the wind scowered that area of 7 inches of snow in about 6 hours.
The funny part is that is where I park at work. The local joke was I had made Mother Nature happy and she was returning the favor. |
Re: Working Man's Burbon
Quote:
:)... Now wait a minute. It always works just the opposite for me. I must be doing something wrong... :lol: LockDoc |
Re: Working Man's Burbon
|
Re: Working Man's Burbon
Quote:
|
Re: Working Man's Burbon
3 Attachment(s)
Oh boy! This showed up at work today!
After more than a year of not finding what I wanted and gathering up parts and pieces I wasn’t really satisfied with I found these! Finally the WMB will have a complete matching set! :metal: |
Re: Working Man's Burbon
Quote:
|
Re: Working Man's Burbon
Nice ! What does the male side look like? My belts from my '67 stepside looked different on the latch cover . Mine had a raised bowtie.
|
Re: Working Man's Burbon
Quote:
Ooooooh! those look good! Hard to beat new stuff. LockDoc |
Re: Working Man's Burbon
2 Attachment(s)
Quote:
|
Re: Working Man's Burbon
Quote:
|
Re: Working Man's Burbon
Quote:
It was an pretty exciting day as I also got my new fuel tank for my Firebird from Tanks Inc. Lots of new to look at yesterday. :mm: |
Re: Working Man's Burbon
Quote:
|
Re: Workirng Man's Burbon
5 Attachment(s)
In response to CG's jonesing for updates here's a little project I started over the weekend. I have talked with LockDoc and he has agreed to set me up with a correct early round ignition key lock and have it keyed to match the doors, and to rebuild my existing gate and hatch lock. The rear lock has been getting awful finicky over the winter so I jumped when Doc posted his ad for ignition locks.
First thing is unlock the lock and remove the key, then remove the cover plate on the gate and after cleaning the area, mark the lock mounting plate's position. (Photo #1 with the hard to see silver line by red arrow) This will save you time later as the plate has a fair amount of play in the mounting holes. This play was designed into the mount to allow adjustment of the gate latches. By moving the plate side to side and up and down the latches can be adjusted for smooth operation. Once the location is marked remove the rod connected to the latch as shown in photo #2. You only have to remove this rod the other one can stay connected. Remove two screws to free the plate. Once the plate is loose push the hatch lever up as indicated by arrow (Circled in photo #3) and wiggle the plate past the lever and out of the gate. Once the plate is in the open remove the two screws circled in photo four and the lock is out. You may have noticed different gates from the photos. Before tearing into the WMB's gate I did a practice run on a spare gate I have. There I discovered a possible problem some folks may encounter. My spare gate has had a rough life and the interior sheet metal has been pushed in a fair amount. Not unlike a pick-up tailgate that has seen lots of rough use. The problem is that the surface that the lock mounting plate is screwed to was pushed down and jammed in place. The latch plate got caught in the area, indicated with the purple circle, down inside the hatch in the area shown with the purple arrow. Once I pried the lock plate loose the whole sheet metal interior piece snapped down about 1/8 inch. This made it impossible to reinstall the lock back in the gate. To get it back together I will have to grind clearance either on the gate or the lock mounting plate. |
Re: Working Man's Burbon
Yeah...I jumped on board with CG's request as well...but your post makes me wonder if there's a way to make the gate's button push in easier? My key/lock works just fine, but it takes a lot of oomph with my poor arthritic thumb to make it pop! By the way...those new seatbelts of yours look incredible!
Woody |
Re: Working Man's Burbon
Thanks for adding more to your post, I feel much better ... I need a smoke haha!
This has to be one of the very top ongoing threads on the board. So much info and so much info the truck side could use if they just wandered to this side now and again. |
Re: Working Man's Burbon
-
I won't clutter up the thread with the whole how to but here is a link to a thread I posted about removing the lock cylinder from the housing after you have it removed from the gate. It kind of goes along with the post above. http://67-72chevytrucks.com/vboard/s...d.php?t=561226 It also shows the location of the code number for the key if there is one. LockDoc |
Re: Working Man's Burbon
Quote:
|
Re: Working Man's Burbon
Quote:
|
All times are GMT -4. The time now is 03:52 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com