Re: slik ricks 67 short wide custom/10
 

Those holes are the rare 67 only taillight cooling duct option more desirable than buddy buckets.:metal:

I found a parts truck with the same option, going to check it out tomorrow, that way it will save you some shipping cost. :lol:

Re: slik ricks 67 short wide custom/10
 

:lol:

Re: slik ricks 67 short wide custom/10
 

well got some parts from the pick n pull and gion back again what tools do you need to take 67 68 side trim off my dad is gonna go soon so any fast replys would be great hey old blue do you remember wahat you used

Re: slik ricks 67 short wide custom/10
 

i do say you have a nice thread here and a nice truck your not gonna run headers?

Re: slik ricks 67 short wide custom/10
 

nope my dad has too many problems with them plus it give it that good look all the pics the fender isnt on so i will tryto get an engine comp. pic for you thanks, rick

Re: slik ricks 67 short wide custom/10
 

I finally found your thread, right on! Any new progress? Good seeing you out at sonic!

Re: slik ricks 67 short wide custom/10
 

thanks your truck aint that bad either i wish i could hear it run every time i see it ,its parked :waah::lol:

Re: slik ricks 67 short wide custom/10
 

well gut i kinda held out on ya little bit i wasnt on awhile ago cause we switched our internet so it was off for a day or two and im too youyng to go into pick n pull you have to be 16:waah:there is a cst 67 (i didnt believe him when he told me until he showed me a pic) but it has a 68 bed, so i told my dad what i needed and he went down there and about 2 1/2 hours and about 40 bucks i got this:
two parking light housings w/ pig tails (the wiring)
the brace that goes on the inner driverside fender
67 mirror and arm (bracket)since they are hard to find
trim for the frnt
door trim
drivers side cab trim
passenger side wheel welll bed trim
the glove box door
the h for chevrolet on the hood
a bunch of the plugs that go on the doors door jamb
and thats it

Re: slik ricks 67 short wide custom/10
 

^^yall didn't buy me anything?;) nice work

Re: slik ricks 67 short wide custom/10
 

:lol::lol:

Re: slik ricks 67 short wide custom/10
 

well im am going to be trading my bed sides (68) for a 67 will be getting tommorow my 67 dog dish chrome and red and hopefully my window rubbers come in tommorrow

Re: slik ricks 67 short wide custom/10
 

well i no i have been laging on the pics but i will get some i got my window rubbers in the mail today got the back window in and now we need the front but that is going to be a pain so we are going to have some one come out and do it but i also got those hubcaps they are pretty good i would say

Re: slik ricks 67 short wide custom/10
 

:wop:


;)

Re: slik ricks 67 short wide custom/10
 

well see if i cant get you some pics then va72c10 well this is the bed i will be trading for my 68 bedsideshttp://67-72chevytrucks.com/vboard/p...pictureid=9732 andhttp://67-72chevytrucks.com/vboard/p...pictureid=9731and anotherhttp://67-72chevytrucks.com/vboard/p...pictureid=9735

Re: slik ricks 67 short wide custom/10
 

here is the engine a little better and my door trim repainted blackhttp://67-72chevytrucks.com/vboard/p...pictureid=9734 andhttp://67-72chevytrucks.com/vboard/p...pictureid=9733

Re: slik ricks 67 short wide custom/10
 

looks like a pretty nice bed and that door trim looks great!

Re: slik ricks 67 short wide custom/10
 

thanks my dad got the trim and i cleaned it

Re: slik ricks 67 short wide custom/10
 

well looks like you are makeing some great progress just keep up the good work i know they take a lot of time and hard work but they are worth it in the long run :chevy::chevy::chevy:

Re: slik ricks 67 short wide custom/10
 

ya i know well hopefully i can get the front window in inbody have any advce
we cant even get the rubber on the window inorder to put it on the cab

Re: slik ricks 67 short wide custom/10
 

What brand seal? Are you using silicone or window spray to make the gasket easier to slide on the windshield? Then put rope in the back, install from the front, and pull the rope out as you pull in and it'll seat itself....sounds easy, huh ;)

Re: slik ricks 67 short wide custom/10
 

no silicone just rubber seals but i dont think we can put a rope in between

Re: slik ricks 67 short wide custom/10
 

I used a fat speaker wire when I helped a friend do it, we also used a heat gun to help soften it up and a suction cup to help move it around. Here's a youtube link that makes it look so easy :metal:

Re: slik ricks 67 short wide custom/10
 

thanks man;)

Re: slik ricks 67 short wide custom/10
 

So did you get the windshield in ? :metal: If not, hurry its supposed to rain on Sunday.

Re: slik ricks 67 short wide custom/10
 

well does half qualify :lol: dont worry i will get it in even if i half to persuade it:sumo: