Re: 63-87 rack and pinion
Rob
I got your rack and started the install. I have an issue with one of the adapters for the rod ends. One will only thread on about a 1/4 inch onto the rack end. The jam nut goes all the way on fine. I think the internal threads on the adapter are messed up. What is the thread type so I can get a tap and chase the threads? Posted via Mobile Device |
Re: 63-87 rack and pinion
Quote:
Thanks for a great product. I am looking forward driving this set up with PB Forward Arms. |
Re: 63-87 rack and pinion
Thought I would post up some pic's of my install on Korbin's '82 C-10. We raised the crossmember up into the frame 1.5" and also used Porterbuilt's new Forward Arms (Lowers only at this point). Here are some pictures from this past weekend:
http://i266.photobucket.com/albums/i...91/FrontPS.jpghttp://i266.photobucket.com/albums/i...91/FrontDS.jpg http://i266.photobucket.com/albums/i...lk91/Front.jpg I still need to do the support bearing, but I am waiting on Rob to post up some pictures of the correct set up for a '73-'87 frame rail. I have a PS pump, hoses, and cooler from a 2000 GMC that we are going to use in the final installation. Enjoy! |
Re: 63-87 rack and pinion
1 Attachment(s)
With a raised crossmember, you need to raise the idler bearing also. I would set the cab on, install the column, and then lay out the steering shaft.
|
Re: 63-87 rack and pinion
Thanks, Rob. I got the adapter yesterday. Tried in on the Passenger side this morning and it fits fine. I need to check the Driver side since that is the side we had issues with. I will do that this afternoon on the way home from work.
I have a bearing like you showed above, once the cab floor is done and under side is painted, we will put it on and set up the rest of the steering system. Thanks again! |
Re: 63-87 rack and pinion
I finally got the time in the shop to put the new adapter on and get that steering bolted together, just need to mount the cab to finish it off...
With the rod ends and adapters all together and both threaded all the way in, I have a bunch of toe out. What should I do to be able to adjust this down for a range between toe out and toe in? Should I cut a little off the rack ends? How much? |
Re: 63-87 rack and pinion
Karl, did you ever get this resolved?
|
Re: 63-87 rack and pinion
I got all the parts together and fit to the chassis. I have not heard from Rob on what I should do to fit the extreme toe out issue. I say extreme since it is about 1/4"-3/8" toed out with the adjustments all the way in...:waah:
|
Re: 63-87 rack and pinion
I've heard that there is some clearance issues with the tie rod ends and the posi links when using a Ride Tech Musclebar?.....looks like there is lots of room for the steering shaft with the LS with headers?...thats good news...
|
Re: 63-87 rack and pinion
Karl, I will check on an OD rack measurement for you on thursday.
|
Re: 63-87 rack and pinion
Rob
Did you happen to get the measurement of the overall rack width? I appreciate all your help with this project. Happy New Year! |
Re: 63-87 rack and pinion
good luck. I still want one of these but I hope you get all yours worked out.
|
Re: 63-87 rack and pinion
Rob
here are some pictures of my install I am trying to do. It looks like I can get a single shaft from the column to the Ujoint on the rack without needing the third joint and support bearing. I do not mind cutting the frame rail and I might even weld back in a strip on the engine side of the flange to "capture the shaft in the frame rail flange. Also, should I cut off about 1" of the column shaft to get the Ujoint further away to help with the angles? I am going to try to call you later today. I might have to wait to talk to you if your at GG's in TX this weekend. Anyway here are some pictures: http://i266.photobucket.com/albums/i...ps132af9ea.jpg http://i266.photobucket.com/albums/i...ps244c31ff.jpg http://i266.photobucket.com/albums/i...ps885c8913.jpg http://i266.photobucket.com/albums/i...psa6d96a4f.jpg http://i266.photobucket.com/albums/i...psadac2cb7.jpg |
Re: 63-87 rack and pinion
Got my steering shaft hooked up. For what ever reason, I did not get the correct U-Joint for the column to shaft. I have to get the correct one for the final assebly, but this one worked out real well for moch up. Ended up going with a straight shaft from the column to the U-Joint on the rack.
http://i266.photobucket.com/albums/i...psd8d310b8.jpg |
Re: 63-87 rack and pinion
Great Karl. glad to see it hooked up.
|
Re: 63-87 rack and pinion
Quote:
Quote:
I really appreciate the work you're doing with C10's to get them to handle better! The "Make it handle" thread, along with a trip to see the Goodguys autoX has completely change the build direction of my '66 C10. I had planned to build my own A-arms but noticed this package deal and figured I'd see what the price was before I went out and bought everything to build my own arm- might not be worth the time and effort if I can just buy them already built like I want (1" forward, added castor, bag plates). I will be going with your R&P kit either way. I searched the suspension marketplace but didn't see the rack/arm combo listed anywhere. Thank you for your time and commitment to the forum! |
Re: 63-87 rack and pinion
Quote:
|
Re: 63-87 rack and pinion
Quote:
I hope to have the truck running and driving by end of next month so I can give a bit of feed back on the steering and linkage. |
Re: 63-87 rack and pinion
Quote:
|
Re: 63-87 rack and pinion
x2!
|
Re: 63-87 rack and pinion
Yes I too am wanting to hear some real world thoughts and experiences, that and for Rob to run a sale special again.
|
Re: 63-87 rack and pinion
We are getting closer. I am a bit behind the schedule we planned, but I don't want to cut corners. I hope to have some better updates in about 3 weeks.
|
Re: 63-87 rack and pinion
Yes sir don't rush it this close to the end. It will be a great build.
|
Re: 63-87 rack and pinion
woops, wrong thread.
sorry Thanks. |
Re: 63-87 rack and pinion
I just installed this. I have CPP tubular arms, sway bar and 3in drop springs and dropped spindles and installed this R&P as part of my 5.3 conversion. I'm having a conflict with the sway bar when turning the wheels. It looks like guys with bags don't use a sway bar... I got to think my truck would sway pretty bad without anything.
Any suggestions on modifying/bending such a large sway bar? |
All times are GMT -4. The time now is 12:03 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com