Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

Sure, our standard radiator will be fine for that. With A/C and being in the desert, I'd go with our upgraded single 17" dual-speed fan. I assume you'll use the PCM / LS harness to control the fan?

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

I have an LT L83 with Ac and in Tx, what would you suggest and could you PM me the cost please?
I would like the best shroud & fan option also.

Thanks
Posted via Mobile Device

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

I see your located outside of Atlanta I am in Athens,
I am working on a 1970 Blazer 2WD factory 6 cylinder but PO dropped in a 454 stroked to a 496 and automatic no ac.....not hooked up yet so not running

What radiator, shroud combo do you have for this setup

Thanks

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

sending PM shortly.


Does the 6-cylinder use the same radiator mounting / supports as the V8? If the width and mounts are the same, it'll be easy. If you wish, you can PM me pictures and a few measurements to confirm.


Sorry for the delayed reply, the forum didn't notify me there were replies.

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

up top!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

we can build radiators for most any application!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

back up top!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

up top again!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

remember to ask for your discount when ordering!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

thanks for the support!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

back up top!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

thanks for the orders!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

we can also build radiators for most any application!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

Looking for a radiator, shroud and fan for a 1966 C20 build that will be running a 400 SBC built for ~500hp.

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

We can easily build that! pm me your zipcode and I can put together a full quote with recommendations.

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

Thanks for the order!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

back up top

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

back up again

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

back up again!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

Not sure what info you need, but I’m looking for a price quote on a radiator/fan setup for a ‘65 C-10 with a ‘00 LS1, 4l60 or 4l80, also running a PSI harness. One more thing, can I get dimensions on the final product? Thanks in advance!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

$450 retail on the radiator ($425 forum member price). For the fan kit, what kind of power are you making and is it naturally aspirated? Size is about 24" wide x 22" tall

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

I should be making about 450 to the wheels naturally aspirated. Thanks for the quick response.

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

With that, I'd recommend our upgraded single 17" that has dual speeds (up to 2,400cfm on high). If you'd like to set up an order, pm me your email address and full shipping address. Then I can put together an invoice and send to you.

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

I'm liking your 56 Belair set up. I need to go and get into my dad's car again and see what it needs. Does the member discount apply to that as well?

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

Yes, member discount applies to any radiator, fan & shroud combo, and any overflow tank. Just make sure to mention you are a member when ordering.

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

SparkyRnD
I am in need of a 4-Row radiator with an electric fan. I have been looking all over and someone on here gave me RnD info to contact you on, so i am doing that. Can you tell me what the price would be and how to go about getting one? PM or here, what ever is easier.
Thanks for your time

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

Thanks for contacting us. On the 4-row part, that refers to 4 cores that are 1/2" thick in brass & copper, which gives you a total core-thickness of 2" (4x.5). On aluminum radiators, we use dual 1" thick cores, so our core-thickness is 2", same as the brass & copper 4-core.

The radiator to fit your rig is $450 retail / $425 forum member price.

I have a few questions so that we can put together a total quote for you:
1. what engine & transmission are you running?
2. do you want the built-in trans cooler (no additional charge)?
3. how much horsepower is the engine going to make?
4. are you using any power adders (nitrous, turbo, supercharger)?
5. do you want to add the controller with relay to control the fan?
6. do you need an overflow / catch can? We have them available in round & square styles.
7. What is your zip code for shipping?

Let me know on the above and I can put together a complete quote for you.

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

back up top

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

How thick are the radiator and fan combos?

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

that depends on HP level as to which fan(s) we choose

500 ish.
Posted via Mobile Device

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

500hp would use our upgraded dual-speed 17" fan ($340 retail / $320 member price). The radiator is about 3.5" thick, and the upgraded 17" fan is about 3.5" thick as well, for a total of 7" thickness (it's a bit thinner than that combined, but we use that for planning purposes to give adequate space).

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

back up top

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

up top again!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

back up again!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

up top

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

remember to ask for your discount when ordering!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

Sparky I have a 383 with no power adders and th350 making about 500hp. Looking for radiator with trans cooler, fans, wiring harness, and overflow.

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

thanks for contacting us! I'll shoot a PM to you shortly

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

back up again!