Re: Markeb01 Build Thread
 

Yippee!!! The brown truck arrived about 14:15 with the new 140 amp alternator, so I set to work immediately getting it installed. The mechanical attachments were dirt simple, until I realized I misplaced one ¼” spacer. So I stuck 4 stainless flat washers together with Krazy Glue which will serve nicely until I can get my kid to machine up another cosmetically correct replacement.

Next up, I soon came to realize the power post on the back of the alternator was larger than any I have previously encountered. This took a few minutes to remedy, replacing the ¼” ring terminals with larger 5/16” components. They crimped in place nicely thanks to my professional ratcheting crimper, with the two biggest terminals placed back to back for ease of installation. Here’s the completed install:

http://imagizer.imageshack.us/v2/xq90/633/C9aJ6y.jpg

It turns out Summit Racing didn’t exaggerate when they claimed the alternator was rated at 150 amps. The voltage set point was 14.8 on both alternators. The amp output specs on both alternators are as follows:

Powermaster amps – idle 105, cruise 127, top end 162
Napa amps – 55 amps at 2000 rpms, 77 amps at 6000 rpms.

My generic calculations indicate I’ll be using about 110 amps when all the main devices are activated – like headlights, fans, a/c, ignition, dash lights, etc. With a fully charged battery showing 13.6 volts - during a quick trip around the block the volt meter only dropped to 13.5 volts once when we stopped after everything had warmed. This was with everything running, and the A/C and fans cycling on and off. And this was with the passenger side spotlight illuminated! I didn’t notice until after we got home. I probably bumped the switch while messing around in the glovebox wiring up the camera power.

It’s pretty obvious the old alternator never had a chance at keeping up with the electrical needs. It’s also pretty apparent looking at the photo I could spend some time cleaning up my master cylinder!

Re: Markeb01 Build Thread
 

Looks good Mark. I may have to upgrade to one of these down the road.

Not sure you have heard about it but I have been reading that DOT 4 brake fluid does not eat paint. However if you change over to it your whole system has to be cleaned as it can be mixed with DOT 3.

Re: Markeb01 Build Thread
 

I’ve thought about swapping out the brake fluid a few times, but I’m basically lazy and the effort needed to thoroughly clean out the old fluid is more work than I’m normally interested in investing.

My wife and I have been putting off a trip we both wanted to make for a while, pending health issues improving and getting the truck back in service as its much more fun to travel in that than our Honda jelly bean car.

So today we took a 150 mile round trip, visiting the resting place of Ruthann’s late mom and husband. From that viewpoint the journey was a complete success. We both enjoyed the time together, paying our respects, taking a few pictures, and reminiscing. Here’s a shot of the truck at the cemetery:

http://imagizer.imageshack.us/v2/xq90/538/3sRdvA.jpg

From a testing the truck standpoint, it wasn’t quite as productive. A few minutes into the trip I noticed the indicator needle on the new Sun Super Tach R wasn’t moving. It was stuck on 1800 rpms. After we stopped, the gauge was indicating normal functioning again, until it stopped moving at 2800 rpms. Again, after the truck was stopped and turned off the gauge fired up and worked normally until it again stopped moving at 2800 rpms once again!

So far I haven’t found any internet threads addressing this problem, so I’ll be going back to my old half sweep tach while I wait for a response from either Sunpro or Bosch on possible resolutions.

The second item on the testing schedule was the new GoPro camera. I made one major mistake which wiped out any viable results. I added a polarizing filter to the waterproof housing mainly for added protection to the lens. In the future, it may prove useful for hand held videos, but it is worthless in a vehicle. Since the polarizing filter is free to be rotated for preferred orientation, it is also free to rattle so loud it wipes out any other sounds or voices recorded. In addition, I didn’t really know what I was doing, so I inadvertently took one picture:

http://imagizer.imageshack.us/v2/xq90/538/hGOp6c.jpg

Yes that’s my hand in the upper left corner. I also wasted enough battery that I only recorded 17 minutes of the return trip, none of which is usable because of the incessant rattling of the filter! But none of that spoiled the trip. We had a great day, and I now have better data to work with. So I’ll make a few adjustments and try again.

Re: Markeb01 Build Thread
 

Awesome trip, thanks for sharing… Hope you hear back about the tach soon...:mm:

Re: Markeb01 Build Thread
 

mark just a heads up ...take some crazy glue and put it on the nuts on the mounts ,let them dry before you put the screws back in ..this is so you do not loss them

Re: Markeb01 Build Thread
 

Thanks for the tip. I’ve also learned a valuable lesson regarding genuine GoPro mounting pieces versus generic items. I bought a generous assortment of generic mounting brackets to save a few bucks, and although they look identical to the real things, they don’t fit the same. Either the female brackets are undersize, or the male counterparts are not as flexible as GoPro parts, making some connections so tight it risks damaging the camera trying to get them apart.

Like so many aftermarket parts in the classic truck world, you frequently get what you pay for, and OEM stands as the benchmark. I resent having to pay the hyper-inflated GoPro prices, but it’s probably cheaper than buying them twice.

I also found the tech support contact for Bosch-Actron (the new owners of Sunpro) and sent them a help ticket. I'm hoping they have an easy solution to the tach problem.

Re: Markeb01 Build Thread
 

On the plus side, I received a prompt, courteous and friendly email response from Bosch-Actron regarding my Sunpro tach technical inquiry. According to Gerald in Tech Support, they have no history of the problem I described with these tachometers. He did offer to replace it free of charge if it was less than one year old.

As much as that offer was appreciated, this wasn’t the answer I was looking for. The new Bosch-Actron version of the “Sun Super Tach” eliminated those words off the face, so cosmetically it wouldn’t be acceptable in my installation.

I then spent several hours searching the web looking for similar tach related failures, and came up empty. So I started wondering if there was something wrong with my installation, even though both tach heads were installed seemingly exactly the same. I speculated maybe I pinched a wire when tightening the cup nut in the back, or perhaps one of the terminal posts was loose in the back of the gauge (under the wire terminal). So I pulled the new full sweep tach back out of the packaging, and was able to tighten the terminal posts another ¼ turn. I thought at first this might indicate the problem, but when I checked the half sweep head, I was able to tighten those posts up another ¼ turn as well.

Once again I reinstalled the new Super Tach, and took the truck for a 20 minute ride. This time it worked perfectly, with no stalling of the indicator! I really have no idea why it quit working in the first place and now it doesn’t, but I’m pleased to have it back in the truck – functioning correctly! Let’s hope it stays that way for years into the future.

Re: Markeb01 Build Thread
 

Glad to hear the Tach is working...;)

Re: Markeb01 Build Thread
 

Thanks Don, but it turns out my excitement about the Super Tach was a bit premature. On a longer ride tonight, as soon as the tach warmed up it again stopped functioning at 2800 rpms. It stayed stuck at that position even after the power was turned off for quite a while. Eventually the indicator needle dropped to the bottom, but that’s it – I’m done. The FZ88R is back in place functioning perfectly, and will remain there indefinitely.

Re: Markeb01 Build Thread
 

that would have me mad too and i would send it back for full refund

Re: Markeb01 Build Thread
 

X2!!!:sumo:

Re: Markeb01 Build Thread
 

Sorry for your frustration Mark.

I guess sometimes we need to just step away.

Re: Markeb01 Build Thread
 

Well we’re back in business. I picked up a second full sweep old school Sunpro tach, and will be sending the previous version back for replacement. The new one works perfectly – no stalling at any rpm.

I also figured out how to get the GoPro to work. I still don’t have anything video related worth posting, but on a run earlier this morning it captured some pretty nice scenes at the plant nursery and on the way home, so I took a couple of snap shots of the display for now, until I can figure a better way to do it electronically. Here’s the truck sitting out front:

http://imagizer.imageshack.us/v2/xq90/537/kjdeSS.jpg

And here we are on the way home, plants in hand:

http://imagizer.imageshack.us/v2/xq90/673/mGrImZ.jpg

The alternator is also working perfectly with no more electrical smell. Last night I also switched back to the 160 degree Robertshaw thermostat. It flows much more coolant combined with the Stewart’s high flow water pump. Sitting in 95 degree traffic it hovers around 190 rather than 200-210 like it did with the 185 degree standard flow thermostat. Since I don’t press this truck into service that much during the winter months, I’ll be staying with the cooler thermostat from now on.

Re: Markeb01 Build Thread
 

Glad to see all is well with the Tach issue, great images from the GoPro...:metal:

…and as always, thanks for the info on the thermostat, helpful info especially here in the southern latitudes where 100 degree plus days are plentiful...:thud:

Re: Markeb01 Build Thread
 

Climbing out after another local journey, I noticed one of the strips of rubber had torn on the clutch pedal and was dangling over the trim. Here’s a shot after I tore it off:

http://imagizer.imageshack.us/v2/xq90/540/Scqyrq.jpg

The missing strip can be seen in the upper right corner, but addition damage can be detected above the horizontal center area, and the last five rows on the lower left corner. The rubber material in the aftermarket pads is just too soft and wears quickly and is prone to tearing. The offset to this is they are much easier to install than OEM pads, as those can be so hard to get on it’s possible to tear the corners trying to stretch them over the steel support.

So I’m resurrecting one of my earlier fantasy projects, having a waffle pattern disc brake pad instead of a plain version or the later deluxe pads with trim:

http://imagizer.imageshack.us/v2/xq90/94/pedalpads.jpg

I really like how the trimmed pads look, but I’m not crazy about having metal around the perimeter of the pad as my foot has slipped off the brake pedal several times, especially with wet shoes. This never happened during all the years I ran the waffle pads.

I had considered cutting the metal portion of the pedal down to fit the Chevelle pad, but the edges are all curved and I wasn’t sure it could be done successfully. I also didn’t want to remove the pedals from the truck, nor lean over the seat long enough to trim the metal down to size with a Dremel tool and cutoff wheel.

So my next thought was to modify the waffle pad and install the stainless “Disc Brake” insert on that pad instead. I’ve worked on this off and on for a couple of years, but never came up with a good solution on three key points. 1. Cutting a neat enough hole for the insert in the waffle pad. Doing it by hand with a hole saw left a ragged edge. 2. Controlling the depth of the insert, so it would sit at just the right height, and 3. How to remove the excess material directly under the metal dome while leaving it perfectly smooth so the dome/insert isn’t damaged by foot pressure.

The answer finally occurred to me tonight. Cut the hole completely through the waffle pad, and install the stainless insert from the rear – after cutting it out of the Chevelle pad complete with the rubber behind it. This way the depth of the insert can be set where preferred by how much material is placed between the insert and the steel brake pedal. A bit of weatherstrip adhesive and it will all be one piece again.

What I’ve done so far is order up three new replacement pads (1 extra just in case). Cut the insert and rubber support out of the Chevelle pad, to the outer diameter of the insert. This retained the “ledge” the outside of the inside rests upon:

http://imagizer.imageshack.us/v2/xq90/538/Ic26nQ.jpg

http://imagizer.imageshack.us/v2/xq90/537/lPpIaE.jpg

http://imagizer.imageshack.us/v2/xq90/537/EH6ts8.jpg

This is my old test mule pad in its modified form, and after cutting out the center:

http://imagizer.imageshack.us/v2/xq90/673/4Ef8UY.jpg

http://imagizer.imageshack.us/v2/xq90/910/tZRx6F.jpg

And this is a crude version of what it will look like when assembled:

http://imagizer.imageshack.us/v2/xq90/538/DhHBa9.jpg

Re: Markeb01 Build Thread
 

:thumbs:
I swear your truck is so far past "done" your just going out of your way to make projects hahah.

Come to think of it....I just realized I've never had a rubber pad on my brake pedal at all...I feel like such a peasant.

Re: Markeb01 Build Thread
 

Another great write-up on details… :metal:

Great idea, stashed away with numerous others already squirreled away...;)

Re: Markeb01 Build Thread
 

I know, right! :lol: The crazy thing though is, his ideas are always unique & well thought out. I don't recall ever reading about or seeing something he has done & thought, well that's just dumb, lol. Even if it might not be 100% necessary to many folks, tweaking/personalizing things to your liking is what it's all about. I keep thinking he's gonna run out of ideas one of these days, but he just keeps coming up with new projects to tackle. :chevy:

Re: Markeb01 Build Thread
 

Thanks for the comments guys. I’ve been telling my wife the truck is “done” for several years (something she routinely reminds me of!). I think her interpretation means I’m not supposed to spend any more money on it, which we all know is just plain silly!

But I’ve changed so many things so many times, I’m ultimately left with enough information to know what I really prefer – even if it requires a step backwards to achieve.

I know a lot of my inspirations are not main stream popular, but figure if they’re worth doing they’re worth documenting. I’ve read so many articles over the years and either had a hard time figuring out how something was done (or never figured it out) – I’d at least take the time to make it easier for the next guy, should anyone else want to do something similar.

It’s what I love about this forum. I’ve swiped many ideas from other contributors I would have never dreamed up on my own, and gained lots of insight into ideas I’d never want, just like so many others looking at my stuff! :lol:

Re: Markeb01 Build Thread
 

And that is about the way I see it as well.

Your thread is entertaining, informative, addictive and long may it live..

Your thread was the first I ever read on here, and was absolutely intoxicating and inspiring.

I am sure your wife feels very pleased and proud of your family toy.

Re: Markeb01 Build Thread
 

Oh stop! My head is swelling so big it's wobbling back and forth and I'm having a hard time holding it up straight! :lol:

And you're right about Ruthann. She's loves the truck, me, and my hobbies. She's offered if my knees ever get so bad I can't drive a stick any longer, I won't need to swap over an automatic as she will be taking ownership of the truck and I get the Honda! ;)

Re: Markeb01 Build Thread
 

Although I can't remember if your thread was the first I read, it may have been Alan's Vitamin C10, I concur with Rian… I always enjoy checking in… :metal:

Re: Markeb01 Build Thread
 

All kidding aside, I really do appreciate the support from everyone that checks in here.

Re: Markeb01 Build Thread
 

When disc brakes first came out in the late 60’s, the coolest part of having them wasn’t their functionality. It was having that cool “Disc Brake” button on the brake pad that made them an instant hit with the drive-in crowd.

And here’s the sample that sacrificed it’s “emblem” for the cause of creating the world’s first authentic OEM 1960 GMC Disc Brake pad! This is a replica for a 1967 Chevelle. The material was so thin and soft I just trimmed around the emblem with an Xacto knife.

http://imagizer.imageshack.us/v2/xq90/538/jnQpzt.jpg

The tools used to make the 1960 GMC disc brake pedal pad were a step drill from Harbor Freight and a 1.5” chassis punch I picked up on Ebay:

http://imagizer.imageshack.us/v2/xq90/661/z0N3M1.jpg

I also used some silicone spray to keep from smoking the rubber as it was drilled. I tried making a prototype earlier in the week, but my original (OEM 1960) pedal pad was so stiff if was very hard to cut and ended up off center:

http://imagizer.imageshack.us/v2/xq90/908/Pwjsw9.jpg

So when the new replacement pads arrived in the mail today, I punched the center of the face and bored a big enough hole for the chassis punch bolt to fit through:

http://imagizer.imageshack.us/v2/xq90/537/uEPccl.jpg

I then turned it over and placed the cutter on the back, with the bolt starting in from the front. This allowed me to center the cutter between the lumps on the backside:

http://imagizer.imageshack.us/v2/xq90/538/2gHwj0.jpg

And this was the result - an OEM 1960 pedal pad for disc brake equipped trucks! I used duckbill pliers to bend the retaining tabs outboard so the emblem cannot extend any further toward the front than the preset depth:

http://imagizer.imageshack.us/v2/xq90/537/Txk468.jpg


http://imagizer.imageshack.us/v2/xq90/538/MBKsR8.jpg

Here is how it looks in the truck along with a matching clutch pedal pad:

http://imagizer.imageshack.us/v2/xq90/912/xLrdYc.jpg

http://imagizer.imageshack.us/v2/xq90/673/bbdcul.jpg

http://imagizer.imageshack.us/v2/xq90/907/1cb0rl.jpg

I’m really happy with the results, although I’m not sure how long these pads will last. They are also very soft and pliable just like the replica Chevelle pad. If they don’t last I’ll just repeat the process!

Re: Markeb01 Build Thread
 

Pedals look great Mark, and I suspect they price in at a level where you can look at replacing them in future if their wear becomes unacceptable.

I love those step drill bits.
Ta2don sent me a set last year, and I do keep them for Sunday Best, but every time I use them, they make me grin madly.

Re: Markeb01 Build Thread
 

Pedal look Great…;) I will have to look at this mod for my trucks...:mm:

Happy Dad's Day!!!

Re: Markeb01 Build Thread
 

Yep, there’s a reason these pedal pads are so inexpensive ($3.95 each), it’s because they’re really cheaply made! I don’t suppose they’ll last all that long, but creating a replacement will be easy.

I think I’ve gone through 3 or 4 sets of those step drills since I first discovered them while watching a bike building show about 10 years ago. They are really fantastic. I wish I had known about them when I did my front suspension swap, as I broke numerous and expensive large bits drilling the frame. I’ve punched through steel up to 3/8” thick with these, and the only time I’ve ever ruined one was when I tried to drill through hardened material and dulled one segment.

Thanks Don. The pedal isn’t for everyone, but I always admired them, and I prefer a pad with rubber around the edges so my foot doesn’t slip off when wet. And Happy Father’s Day to you and all the other dads out there!

Re: Markeb01 Build Thread
 

I discovered yesterday I hadn’t tightened the petcock on the radiator sufficiently a few days ago when I changed the thermostat, and had a drip making a mess of the garage floor. I’ve kept the existing valve way too long, only because I liked the outlet tube on the end that allowed attaching a hose to direct the coolant flow into the drain pan. Unfortunately the drain is under the fan bracketry blocking the view when opening or closing the valve. Due to its age the ears were bent over towards the radiator, making it very difficult to determine if it was tight or not – or to even get a grip on it.

http://imagizer.imageshack.us/v2/xq90/905/DuM0Ye.jpg

The other problem I experienced virtually every time I drained the radiator, the hose plugged into the end of the extension would stick in the tube and rotate around upside down and shoot coolant over the top edge of the drain pan, fundamentally negating the value of the hose extension!

So I went through my brass fitting tote last night and came up with a short extension to move to petcock away from the radiator, and turn it 90 degrees. This allows the coolant to drain directly under the lower radiator hose and into the pan without need for a hose extension, and provides easy access to the ears for opening and closing:

http://imagizer.imageshack.us/v2/xq90/540/ivG9K3.jpg

It took me a while to remember where the new drain came from, as I’ve never purchased one individually that I can think of. Then it occurred to me, this was the valve off the bottom of the compressor. I always remove those and connected a ball valve to the tank for easy release of the moisture buildup.

Of course now that I’m intending to leave the 165 degree thermostat in the engine perpetually, I probably won’t need to use this again for decades!

Re: Markeb01 Build Thread
 

Had an interesting adventure this morning, not exactly truck related. Since it’s supposed to get up to nearly 100 degrees today, I got up early and went out to photograph my wife’s corn crop. I started a few weeks ago to record the growth progress. Here it is in the beginning, and what it looks like today:

http://imagizer.imageshack.us/v2/xq90/540/G2Q0zp.jpg

http://imagizer.imageshack.us/v2/xq90/673/I94P1q.jpg

An hour later I’m showing my wife the pictures, and she points out what appears to be a rather large snake in the foreground. She thought I was messing with her when I suggested it looked like a Gila Monster (since I’ve done a diorama of the movie by the same name). Then she realized I wasn’t kidding, and we forwarded to the next photo, and although I never captured the full image, I must have parked my tripod nearly right on top of him!

http://imagizer.imageshack.us/v2/xq90/537/BrG27i.jpg

http://imagizer.imageshack.us/v2/xq90/661/ob5Rr8.jpg

I routinely set up the tripod within 12 inches into the lawn from the near side of the edge blocks before the rocks. He either slithered between the legs of the tripod or right against it. And I’m standing right next to it in shorts and sandals! I generally pride myself on my acute awareness of any potential threats in my environment, but I’m normally looking for two legged creatures, not snakes. Looking at the pictures I was in disbelief how close I was to this thing and never saw it once. I have no idea what kind of snake this was, but it appears to be about 3-4 feet long and 2.5-3” in diameter. It may be a pet that got loose, or the start of the next monster movie serial!

If anyone knows more about snakes than we do, I’d sure appreciate some input as to what kind it was and whether or not they are poisonous.

Re: Markeb01 Build Thread
 

not a snake I am familiar with but appears to be a boa or python, and my guess is a loose pet

Re: Markeb01 Build Thread
 

Looks like a spotted python. Would be hard to say without better pics of the head.

Have a buddy whos big into reptiles and he passed the info to me.

Re: Markeb01 Build Thread
 

Nice garden, Mark. That snake must be a gardener snake:lol:

Re: Markeb01 Build Thread
 

Local opinions range from King, Bull, or Corn snake, which are all similar in specifications. None or poisonous, they all bite but kill by constriction. Looking at the photos again we're thinking the thing was more like 6 feet long as well. We've also read that they make great pets, but are famous for being escape artists so it probably was a pet.

Re: Markeb01 Build Thread
 

hey markeb, saw this and thought of you.

http://fortsmith.craigslist.org/cto/5074437999.html

I saved the pictures to my photobucket if the link goes dead.

Re: Markeb01 Build Thread
 

Excellent, thanks for thinking of me! I do like those 73 beds and still haven't given up on the idea for my own truck yet. I'll be sure to save the photos too. Thanks again.

Re: Markeb01 Build Thread
 

Okay, here’s a small truck related item. After making a few more minor changes in the interior (again) I spotted an item I just couldn’t live without. A Remove Before Flight key chain tag. After my time in Vietnam working around airplanes, I just thought they were too cool to pass up:

http://imagizer.imageshack.us/v2/xq90/912/4J2llR.jpg

http://imagizer.imageshack.us/v2/xq90/901/wADK7T.jpg

Embroidered on both sides, it not only looks pretty cool hanging in the ignition switch, its actually changed the way I’ve carried my keys for over twenty years. Retrieving the truck keys from my pocket has never been easier. Here’s what the tag look like from the vantage point of the GoPro in the back window:

http://imagizer.imageshack.us/v2/xq90/908/ACzimH.jpg

And another mediocre video production with our new GoPro:

https://www.youtube.com/watch?v=guXC...ature=youtu.be

All of these videos are with the camera microphone. I need to get a plug in version as it makes a huge difference in how the sound comes across.

Re: Markeb01 Build Thread
 

Trucks looking sharp as always and great looking key chain. Had a buddy at Langley AFB a few years back who worked on F22's...used to get them off him.

Also thought I'd share my garden visitor that I literally stepped over Sunday night at 9:15pm. I have no problem with non-venomous, but this dude was 2ft long and venomous (Copperhead), so I dispatched him.

Re: Markeb01 Build Thread
 

That can be disturbing for sure! Long ago in Vietnam I was leaving the head and stepped on a rat the size of a house cat. I was wearing shower shoes and perhaps a towel at the time. I darn near fell over from twisting my ankle, shined my light on him and he was none too happy about the experience either! He gnashed his teeth and snarled at me. I wasn't armed at the time so he just waddled off and I was glad to be on my way without any bite marks!

Re: Markeb01 Build Thread
 

That's too crazy about the snake being practically right under you & not knowing until seeing those pics. Kinda gives me the heebie-jeebies! :lol:

I dig the key chain tag, & it compliments your interior nicely. The truck sounds great as well! I noticed the blue steering wheel in some segments. Did you temporarily switch back? Oh, & nice job on the brake pedal pad. :chevy:

Re: Markeb01 Build Thread
 

I gotta admit seeing the snake in the photos kind of gave me the willies too! When I saw the pics, and realized I was standing there in sandals and shorts, it kind of set me back. Especially because I'm a former Marine and pride myself on always noticing everything I my environment. I was in disbelief I could miss something so big, so close, and moving!

Yep, I switched the steering wheel again recently, and the shift knob. At this point it appears the original white Hurst knob will remain permanently, along with the two red safety covers over the left hand toggle switches.

I prefer the blue wheel, while my wife and every woman that has ever stuck her head in the truck likes the red one better! I also like the black wheel (as do most guys), but must admit it looks rather harsh with no color at all (just black and chrome). So for now the red wheel will stay, until I get sick of it again and go back to the blue one. It's less than a ten minute job to switch them, so I can do it whenever the whim hits me.

And since my wife really likes the red version best, I even made up a sheet for her explaining exactly what to do to put it back in - in case I'm not around and she needs to reinstall the red wheel at some point in the future!