Re: '72 Cheyenne K10
You have a factory Air Condition cab. You might want to think about vintage air if you are really going to fix it up.
|
Re: '72 Cheyenne K10
4 Attachment(s)
I took the truck on it's longest drive a few miles across town today. Brakes could definitely be better. A friend is helping me with building a center console from scrap cedar. Stopped by my friend's new brewery to pick up a couple crowlers on my way home.
Attachment 2013533 Attachment 2013534 Attachment 2013535 Attachment 2013536 |
Re: '72 Cheyenne K10
I am so frustrated with the brakes on this truck. Two shops looked at it and told me the booster isn't big enough. Booster manufacturer says it is plenty big. No shops want to work on it at all. I have bled and bled again and bled again. The brakes suck. They slow down okay, but are terrible for stopping. I have to grab the steering wheel and push with all my might to the floor to stop on a downhill driveway. If a dog, cat, or child jumps in front of me they are dead for sure.
|
Re: '72 Cheyenne K10
Maybe a vacuum leak somewhere is taking away from the booster?
You can always switch to hydroboost...it's pretty sweet. |
Re: '72 Cheyenne K10
4 Attachment(s)
Center console project is finished (except bolting to the seat frame). I think it turned out pretty good.
Attachment 2015116 Attachment 2015117 Attachment 2015118 Attachment 2015119 |
Re: '72 Cheyenne K10
console looks great.
|
Re: '72 Cheyenne K10
Truck looks great!
|
Re: '72 Cheyenne K10
4 Attachment(s)
Thanks guys!
I changed the oil today (yeah, I know I should have done that when I first got it). The filter was seriously stuck on and started to crush with a strap wrench. I turned to YouTube and found this cool trick to drill some holes and put screws through an oil filter socket into the oil filter. This worked much better than stabbing a screwdriver through it. Attachment 2015726 Attachment 2015727 Attachment 2015728 Attachment 2015729 |
Re: '72 Cheyenne K10
Stabbing the screw driver. Been there that’s a mess.
|
Re: '72 Cheyenne K10
4 Attachment(s)
I also took the passenger side hub apart to replace the rotor today. The bearings look good, so I'm just going to repack everything with new grease.
Attachment 2015823 Attachment 2015824 Attachment 2015825 Attachment 2015826 |
Re: '72 Cheyenne K10
From these pictures, it looks to me like that rotor is glazed over. Hopefully your brakes will be more responsive after you replace it.
|
Re: '72 Cheyenne K10
Quote:
|
Re: '72 Cheyenne K10
2 Attachment(s)
Hey jimbosprint
Nice thread I met you briefly the other day But I really didn’t know Until now :chevy: It was raining And I had a long drive in front of me |
Re: '72 Cheyenne K10
Quote:
|
Re: '72 Cheyenne K10
Last summer, I had poor braking for a while until I realized that the rear shoes needed more adjustment out. Turned in the star wheel to get the drums off and didn’t get set out enough. Discovered this when wife set the parking break and I dint know about it until the first stop and was like whoa, that is a lot better what changed. If you haven’t set the shoes yet that may help as well. My thought is all the initial boost was used to close the air space. Hope this helps.
Very nice truck btw, I too love the color. |
Re: '72 Cheyenne K10
5 Attachment(s)
You never know what you will find when you take em apart. Driver side hub was very rusty. WD40 is good stuff. I think most of the parts can be saved, but I am tempted to replace the bearings at least. Any advice from the peanut gallery?
Attachment 2016249 Attachment 2016250 Attachment 2016251 Attachment 2016252 Attachment 2016253 |
Re: '72 Cheyenne K10
Soak the rusty hub dial pieces in Evaporust if not pitted and gone. Once the rust is gone lube and install. http://67-72chevytrucks.com/vboard/s...0&postcount=18
|
Re: '72 Cheyenne K10
Personally, I would replace bearings/races.
|
Re: '72 Cheyenne K10
5 Attachment(s)
I got the driver side back together. I had a little trouble with getting the bearing adjusted, but I think I have it right. The locking hub works good now.
The new pads rub a little on the new rotors. I am sure the caliper was opened all the way up. I hope the problem solves itself with a little use. Attachment 2016587 Attachment 2016588 Attachment 2016589 Attachment 2016590 Attachment 2016591 |
Re: '72 Cheyenne K10
4 Attachment(s)
Passenger side hub is back on, but I didn't get the caliper back together yet. This hub lock is more difficult to get into the free setting for some reason. Everything feels like it moves smoothly inside to me.
Attachment 2017144 Attachment 2017145 Attachment 2017146 Attachment 2017147 |
Re: '72 Cheyenne K10
1 Attachment(s)
I got the passenger side back together today and went for a test drive. The brakes slow down in a hurry just fine, but they are not good at stopping. There is no locking up the wheels. It isn't possible. Plenty of brake pedal there, but they are squishy and it takes a lot of leg to stop. Maybe the booster is bad. I don't know what to do.
Attachment 2017265 |
Re: '72 Cheyenne K10
I’m not an expert, but I recommend bleeding the system again. I say that because you say the pedal is squishy. I’ve gone through your thread but I don’t remember if you got a new master cylinder, if you did get a new master cylinder did you bench bleed it first?
|
Re: '72 Cheyenne K10
Quote:
|
Re: '72 Cheyenne K10
I just ordered chrome bumpers. I can't find anyone to take thousands of my dollars and fabricate some nice tube bumpers for me, so instead it goes to reproduction parts. I am done wasting my time on people that lie when they say they can work on it in two weeks.
|
Re: '72 Cheyenne K10
What are your thoughts on adding a push bar/brush guard?
|
All times are GMT -4. The time now is 12:02 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com