Re: New 64 Stepper Project
 

Anyway here is the back-side of the frame where the power steering gear box is mounted. Before the powdercoating I had a hole or two welded up. I used grade 8 bolts and extra heavy washers as well as blue locktite and lock washers. :)

Re: New 64 Stepper Project
 

Dang, just saw this. Really clean build going on here. Looks like every little nook and cranny is buffed to perfection. Superb work!

Re: New 64 Stepper Project
 

Thanks but I have much cleaning to do before it's ready for prime time. :)

Re: New 64 Stepper Project
 

Okay finished the brake bleeding front and rear. Then operated the electric parking brake unit to adjust the rear brake travel. Since one sides cable is longer than the other I had to make sure they travel the same, so now they do.

Re: New 64 Stepper Project
 

Worked on re-fitting the radiator and side baffles. I had previously made the top front baffle so I installed the rubber and re-fit it all together to see (post paint) how it looked. What do you think so far?

Re: New 64 Stepper Project
 

Man that sure looks good.....Hope the hood spring mod works for you....
Joe

Re: New 64 Stepper Project
 

Looks good to me :thumbs:

Re: New 64 Stepper Project
 

So here is a closeup of the top radiator seal I was talking about. I plan on using the hood anti rattle rubber that comes with three pieces in the kit, since I have one for the side I need another for the other side of the radiator if anyone has a spare. :) Instead of the folded over rubber, I will Plastic-dip the end.

Re: New 64 Stepper Project
 

That looks good!

Re: New 64 Stepper Project
 

Thanks :)

Cool. ;)

Thank you. :lol:

Re: New 64 Stepper Project
 

Installed the lower radiator seal and then stapled it all in. Actually used super weatherstrip adhesive (3M) and wire and patience but it looks okay.

Re: New 64 Stepper Project
 

Then I put together the grill and headlight brackets getting ready to put the grille together and wire it in.

Re: New 64 Stepper Project
 

Wow looks great! You mind telling me your solution to having the proportion valve hanging off the master? Did you build a bracket for it on the frame rail? I am not to happy with the lines all cluttered in the engine bay and yours look perfect.

Re: New 64 Stepper Project
 

Thank you.
Starting on page #7 at post #171 I explain it. http://67-72chevytrucks.com/vboard/s...=666226&page=7

Re: New 64 Stepper Project
 

I've been wiring up my truck and also installed the wiper motor and wiper transmissions. I had to wire wheel the trans paint them lube them etc. They run perfect after I got the switch dialed in, they even park. :)

Re: New 64 Stepper Project
 

Started wiring the truck, not finished but you get the idea:

Re: New 64 Stepper Project
 

Very clean work.....

Re: New 64 Stepper Project
 

Your wiring looks great. I'm just a little behind you. I've got the fuse panel mounted and I spent about 3 hrs. today untangling wires. This nice work gives me motivation.

Re: New 64 Stepper Project
 

Thanks guys, ya those wires are a mess when you get them I never thought I'd get this far. I had to buy some terminals for the fuse panel and replace a couple wires I thought were too small and remove a couple I wasn't using. That gave me the opportunity to clean it up. In case you want to know - http://www.repairconnector.com/produ...52d14-AWG.html
http://cdn2.bigcommerce.com/server50...80.500.jpg?c=2

Re: New 64 Stepper Project
 

I was trying to make sure I bought the right speedo cable so I took an extra piece of 3/16" tube and ran a 63" length from the gauges to the trans are where the planned 200R4 threaded connection will be. So I am sure that it will work.
I know that the ATP Y-804 Speedo cable is 5/8"-18 gauge end and 7/8"-18 Trans end at 63" long.

Re: New 64 Stepper Project
 

I'll be interested in how the 200r4 works for you.....considered that myself since its a direct replacement for my T350......

Re: New 64 Stepper Project
 

Sent you a PM Joe.

Re: New 64 Stepper Project
 

Another way to skin a cat - I just saw this pic from Clemdaddy's post. See the proportioning valve on the inside of the frame?

Re: New 64 Stepper Project
 

I started working on the hood lamps. I used an American Autowire grommet for the firewall plug for the hood wires to include a ground wire to the lights, I used some push-mount wire ties in the interior of the hood wiring, they are hard to even notice. The pad isnt installed in the hood on the pic below, hard to see with so much red.

Re: New 64 Stepper Project
 

I plan to use F6 wire covering for most of the wire but it hasnt arrived yet so I got started anyway. I'll change it out when it arrives.