LS factory cruise control hook up
4 Attachment(s)
I made this diagram for Clyde65, but thought others might be able to use it. This is just a schematic drawn to hopefully be a little clearer than the factory service manual. This is how to hook up a factory cruise control module for cable throttle body's. It's really fairly simple, you just need to make sure you get the right module. I personally used one from an Astro van, but mid 90's and up S-10's use the same module. The one you want will NOT have a wire in the "H" terminal of the module plug (see 2nd pic, notice the missing wire in the middle). Once you have that you'll need a 4 prong brake light switch, it will have 2 normally open and 2 normally closed terminals. These can be found in alot of 70's and up GM cars and trucks.
To run the factory cruise you need a 4000 pulse per mile signal. This comes straight out of the PCM, it's the signal to the speedo, radio ect. On a '99 to '02 truck, and F bodies it's the C2 connector (the red one) pin 50 dark green/white. The one at C2 49 is a 128k ppm and is only used for ABS, Don't try to use it. You'll need a 4 wire cruise control switch to turn it on and off. If you have a '83 or newer column and it has cruise on it, it should be a 4 wire. For older columns that use a single screw to hold the turn signal lever the '81-'82 trucks and vans have a lever that can be converted that will work. I posted a "how to" here. http://67-72chevytrucks.com/vboard/s...=cruise+switch Other than that it's a matter of hooking up the cable to the TB and mounting the module. This will work on almost any EFI engine that has a 4k PPM speed signal so if you have a TPI, LT1, or LS, all GM's use that signal. I have this same set up on my own car and have about $50 max in the whole thing, and it works way better than the aftermarket cruise I have on another car. this cruise works flawlessly! set it and it stays there and doesn't fluxuate like the aftermarket. |
Re: LS factory cruise control hook up
3 Attachment(s)
The brake light switch that you will need and pics of the lever. Also it should be noted that you can't run LED brake lights with this system, because the module needs to see a ground through the G terminal, and LEDs don't have enough resistance.
|
Re: LS factory cruise control hook up
You are an angel! A manly, tough angel but an angel none the less.
One question, will a 99-02 GM truck module work also? Would it be different in any way? Posted via Mobile Device |
Re: LS factory cruise control hook up
VERY helpfull thread... sticky???
|
Re: LS factory cruise control hook up
Quote:
|
Re: LS factory cruise control hook up
Good info! Thanks!
|
Re: LS factory cruise control hook up
1 Attachment(s)
In reference to post #2, LED lights, you can use LED lights with these cruise controls using a relay to allow the cruise to find the ground. Here is the diagram. I used it on my truck and it worked. Hope this helps. (my truck is DBW but this should still work).
|
Re: LS factory cruise control hook up
Quote:
Posted via Mobile Device |
Re: LS factory cruise control hook up
Quote:
lMy personal car doesn't have the brake switch I showed, it has the switch under the floor, and you can only find single switches, so I used that with a relay to control the TCC, and the cruise is tapped into that. But I think if you're unsure of your wiring abilities its best to keep it simple. BTW, nice diagram, I wish I knew how to draw stuff on the computer but I don't so you all get my hand drawn diagrams. Posted via Mobile Device |
Re: LS factory cruise control hook up
Your right LS1nove, it dosnt have a wire in that one spot. So cool, I have it all in there and ready but like I said before, wiring was too confusing. I will wire it the next day off I have...if I have one.
|
Re: LS factory cruise control hook up
Anyone have this for drive by wire throttle bodies with TAC modules? (example 2002 LQ9 engine)
|
Re: LS factory cruise control hook up
Quote:
Posted via Mobile Device |
Re: LS factory cruise control hook up
Do you know that from experience or is that info just from looking at the diagram?
Thats the thougth I had as well, but whether computer wise it actually works in real life or not I have not gotten answered. This is a big part of my decision (if cruise works with DBW) to keep the DBW or put a cable throttle body on. Thanks, |
Re: LS factory cruise control hook up
Quote:
On your 2002, the wires on the TAC you need are, connector C1 (the engine harness one, not the one going to the pedal) pin 4 dark blue wire is the set/coast, pin 5 gray/black wire is the resume/accel, and pin 14 gray wire is the on/off. You will need an ignition 12v source to power these through the switch. You also have to have the brake lights hooked up and the correct brake light switch for it to work, but that's really all there is to it. |
Re: LS factory cruise control hook up
My set up is from an 01 Suburban DBW. I used the control switch period correct for my column and followed Ackatack's wiring on his post and my cruise works great. Of course I had to use the relays for the LED lights and relays for his diagram to reverse the polarity of the switch to match the TAC. Here is a link to his post http://67-72chevytrucks.com/vboard/s...d.php?t=398006
|
Re: LS factory cruise control hook up
Please do a wiring diagram for DBW
|
Re: LS factory cruise control hook up
I'm out of town this weekend. Will get a diagram posted on monday.
Posted via Mobile Device |
Re: LS factory cruise control hook up
1 Attachment(s)
Quote:
If you have any questions, just ask and I'll try to walk you through any problems that you may have. |
Re: LS factory cruise control hook up
Am I correct
4 wire cruise switch ---- TAC Red - ------ ------- -12 volt Blue - ------ ------ -14/cruise on Green - ----------- -4/set-coast Yellow - -------- -5/resume-accell Then hook hot w/brake applied to - 6 |
Re: LS factory cruise control hook up
Quote:
|
Re: LS factory cruise control hook up
We have set several of these up without using the stalk switch on hotrods. Just a toggle switch on the gray wire (on/off) & momentary push button on the dk blue to engage cruise. Just don't have resume/accel option which we didn't care about.
|
Re: LS factory cruise control hook up
Quote:
Posted via Mobile Device |
Re: LS factory cruise control hook up
Well this is encouraging that I can easily have cruise with DBW.
Now someone needs to figure out how I can manually blip the throttle from the engine bay to impress my buddies when there looking at the engine with the hood up like you can on a cable setup... |
Re: LS factory cruise control hook up
Well it looks like I'm out of luck
my PSI harness doesn't have wires in the 5 & 6 pin |
Re: LS factory cruise control hook up
Quote:
|
Re: LS factory cruise control hook up
I grabbed two 4 wire switches from the junk yard.. but I couldn't find a good lever assembly....
|
Re: LS factory cruise control hook up
Quote:
Posted via Mobile Device |
Re: LS factory cruise control hook up
Thanks you have answered many questions!
|
Re: LS factory cruise control hook up
Mine is hooked up and working! now for a long road trip!
|
Re: LS factory cruise control hook up
Quote:
Posted via Mobile Device |
Re: LS factory cruise control hook up
Quote:
|
Re: LS factory cruise control hook up
Quote:
|
Re: LS factory cruise control hook up
Aren't those levers pretty expensive. IIRC those are the ones LMC sells for $230. I have one that came out of a 1980 Suburban but it is pretty rough. Where did you get yours and where did you get the sheet of labels???
http://67-72chevytrucks.com/vboard/a...1&d=1330398300 http://67-72chevytrucks.com/vboard/a...1&d=1330398300 |
Re: LS factory cruise control hook up
Quote:
I had the labels made, if you want one, id sell you one for. $7 shipped. Posted via Mobile Device |
Re: LS factory cruise control hook up
I will probably take you up on that, let me dig up my old lever and see how many wires it has and if it is usable. Thanks!
|
Re: LS factory cruise control hook up
Subscribed!
|
Re: LS factory cruise control hook up
so in order to run cruise with an on off toggle and a momentary switch i need to run a jumper wire with 12v from the on off switch when its on to the middle of the momentary switch ?
|
Re: LS factory cruise control hook up
Quote:
I have a momentary push button that provides 12+ to terminal B when pushed to set cruise. If i hold the button in it will coast until i release the button. Terminal C i remove, everything else is the same as posted. |
Re: LS factory cruise control hook up
:D
Quote:
What did these come out of again.... 3 or 4 wire doesn't matter... |
Re: LS factory cruise control hook up
Quote:
|
All times are GMT -4. The time now is 09:48 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com