'62 GMC 3/4 ton project
Hi
I'm new around here and am finding this is a great forum with a ton of knowledge. Thought I'd share the plans I have for my truck. I have a 1962 GMC 3/4 ton long bed two wheel drive 4 on the floor . Truck is all original except the 305 v6 has been replaced by a 350 v8 and the front end and brakes have been rebuild. I plan to build this truck into a reliable everyday work truck for me to run a small electrical contractors shop. I have the front end,hydra boost, pump and gear box from an 81' Chevy c30 dually and will retain the factory Dana 60 and fresh drums out back. The cab bed and fenders will come off and rust will be repaired but I'm not building a show truck so minimal time will be spent making things straight. All the rubber will be replaced. I want to cover every inch of this truck in POR-15 just to see how it works, Truck will be two tone, gloss black on flat black. Cab floor will have a bed lining, wood bed will be replaced with 3/4 inch marine grade plywood then bed lining as well. I've owned this truck for ten years now and I am happy to finally have the means to build her as I see in my dreams. Edit, So a few things have changed, I'm not going to paint it black anymore, I now want to save as much original paint as possible and match the patina as best I can in the areas that get major repair so the rockers and the roof. I'm also not replacing the bed with plywood or bed liner, I have new pine bed boards and non polished stainless strips from Mar-K as well as some of their bed sheet metal. I'm also biting the bullet and going out with the sm420 and in with a new overdrive transmission. |
Re: 62' GMC 3/4 ton project
Welcome aboard! Too bad the 305 v6 is gone. You would have liked that. They were a beast! Have one in my 64 GMC and I slapped a 4 barrel on it...now I can't shift fast enough. haha Sounds like some good plans and WE NEED PICTURES. :mm: :chevy:
|
Re: 62' GMC 3/4 ton project
Welcome, We love pictures.
|
Re: 62' GMC 3/4 ton project
3 Attachment(s)
Okay I think I figured out how to post pictures.
|
Re: 62' GMC 3/4 ton project
3 Attachment(s)
Just a few more because I like pictures too.
|
Re: 62' GMC 3/4 ton project
Welcome.
I see loads of detail in the photos that I "approve" of. Motorbikes, trees, an African Grey, and the colour of the truck, yup, I like the colour. Glad you are headed for a good build. You should ask the moderators to move it into the Builds and Projects section. |
Re: 62' GMC 3/4 ton project
Looks good! Lotta parts handy as well. :chevy:
|
Re: 62' GMC 3/4 ton project
2 Attachment(s)
Okay I'm back! I've actually made progress over the last month or so and I'm on track to keep powering away at getting her finished. We are moving to Portland and I'm stuck here until This truck is road worth. I hope to be more regular about updating progress on this build. I'll start by attempting to upload a few pictures.
|
Re: 62' GMC 3/4 ton project
3 Attachment(s)
A couple more and one of the main reason I've taken a break from the truck. Her name is Hot Rod and she's a miniture English Bull terrier.
|
Re: 62' GMC 3/4 ton project
3 Attachment(s)
So many pictures!
|
Re: 62' GMC 3/4 ton project
4 Attachment(s)
So this is current. getting the duel tanks wedged in place. Tanks are from LMC.
|
Re: 62' GMC 3/4 ton project
Good lookin pup :thumbs:
I previously missed the fact that this truck originally came with a Dana 60. That's cool. What gears does it have? I wouldn't have thought two of those fuel tanks would have fit like that. Good thinking out of the box. |
Re: 62' GMC 3/4 ton project
5 Attachment(s)
Thanks Captian! She's turning into a great dog. Gears are 410's, I originally thought I would only get to have the one tank but on my initial mock up I noticed There was a ton of room and after taking many measurement decided to take the chance and ordered a second tank.
On a different note, I installed your steering box adapter on the x-member frame using the DOM tubing through the frame. After getting the box actually mounted I realized that If i just made the DOM longer before welding it into the frame I wouldn't need the adapter. I'm not that great at making my welds look pretty yet but I don't see any better way to learn than just diving in. |
Re: 62' GMC 3/4 ton project
Yes I see what you did. That works fine for those that have welding capabilities, but not all do. With the original plate assembly the top tube could be welded after the truck is driveable again. Not that there is anything wrong with what you did.
|
Re: 62' GMC 3/4 ton project
Yes, I agree. When I originally Installed the adapter and back plate it worked fine without any welding. :metal:
|
Re: 62' GMC 3/4 ton project
3 Attachment(s)
About 90% finished with the sand blastin!!
|
Re: 62' GMC 3/4 ton project
I'm in I too like the looks of the dual fuel tanks! Keep it up!
|
Re: 62' GMC 3/4 ton project
A 62 foot GMC? Got any pics?
|
Re: 62' GMC 3/4 ton project
Looking good. Looking forward to future progress.
|
Re: 62' GMC 3/4 ton project
Quote:
|
Re: 62' GMC 3/4 ton project
Finally had a chance to get some work done on my truck after moving my family to Oregon. My truck and myself are still in California and now my wife and Daughter are in Happy Valley Oregon. I'm stuck in California to take care of a few obligations and to get my truck together enough to drive it north. In the weeks before packing them up I was able to finish the swaybar mock up and sandblasting the frame. My wife also talked me into upgrading the transmission so we ordered a new adaptor bell housing and a brand new (rebuilt) NV4500 from Advanced Adaptors. The new bell housing moves the clutch fork to the drivers side and I will need to fabricate a new transmission mount as well I was worried the factory manual transmission mount would interfere withe the new bell housing. Today I mocked up the bell housings a took some measurements, I do believe it will NOT interfere. Now I can move on to blasting the front end components and finally paining them and the frame.
|
Re: 62' GMC 3/4 ton project
Hey you'll have to pass through Grants Pass I think on your way up to Happy Valley, I am 36 miles east of there. haha To bad Happy Valley is 4 hours from my place. Maybe one of these days when you get the ol truck together we can meet halfway. haha
|
Re: 62' GMC 3/4 ton project
5 Attachment(s)
Making slow but steady progress.
|
Re: 62' GMC 3/4 ton project
5 Attachment(s)
Well I'm in Oregon for a couple weeks. Moved my wife and daughter to OR in October but I've been in California trying to get my truck and some other jobs done. making good progress but can't wait to get back and build the rolling chassis.
I'm almost finished up with the passenger side sheet metal repair. It did not have much rust but some ass "me" crashed a trailer into the truck a few years ago and bent things up fairy bad. I'm just happy I was able to make the door fit okay. I have minimal welding experience and this is my first time with sheet metal, hopefully the other side comes out nicer. I was toying with building a frame rotisserie for a long time now and finally just did it. I wish I would have done it from day one! It would have made sandblasting a hell of a lot easier. I was able to get POR15 and a top coat on the frame (sorry no picture of the black yet)on the 18th before flying to Portland on the 19th. The paint will be fully cured and I can start building the chassis as soon as I get back on the 3rd. Also I'm really looking forward to getting my brand new NV4500 to fit.Fingers crossed!!! So I know its the wrong years but I found this old picture of my other truck from when I was 17 and it was still in one piece. We brought the '72 (most of it so far) to Oregon and plan to finish building it there. Going to finish building the '62 in California and then use it to drag a bunch of tools and truck parts 700 miles north to my new house in Clackamas. |
Re: 62' GMC 3/4 ton project
4 Attachment(s)
Just a few more then I'll stop bugging everyone.
|
Re: 62' GMC 3/4 ton project
Looking forward to seeing how you fit that NV4500 into your truck. Going to be a nice setup. BTW, if the 62 GMC floor is like the 62 Chevy, it is going to be real tight for the clutch fork on the driver side.
I'm also curious about how you're going to do the parking brake. |
Re: 62' GMC 3/4 ton project
Quote:
|
Re: 62' GMC 3/4 ton project
Quote:
Was your c20 a high hump? I don't see the fork being an issue but I'm just going off of pictures at this point. The fork looks to be lower than the bottom of the cab. As far as the brake...... Ummmm... yea! Whatever happens I want to use the original lever mounted on the new transmission somehow. I was thinking if I can get a yoke flange that will fit the nv4500 then maybe I can adapt the original drum to it, I guess we will see what happens when i get to that point. Second option is to figure out how to add e brake to my rear drums and run a cable from the stock lever. third option would be disk brake upgrade with Cadillac calipers. I really don't want disks on the rear as this will be a well used work truck but it is an option as one way or another I want to have an e brake. I could put a line lock in but I know it's not DOT or a good Idea to leave the system pressurized. I'm down to hear other thought as well. |
Re: 62' GMC 3/4 ton project
Quote:
|
Re: 62' GMC 3/4 ton project
Is there a reason you did not just go with an original NV4500 bellhousing with the factory hydraulic clutch slave? Then all you would have to do is change your clutch master and run the line.
|
Re: 62' GMC 3/4 ton project
Quote:
|
Re: 62' GMC 3/4 ton project
CFab is right. The easiest way is to mimic as closely as possible the factory configuration. Finding a factory style NV4500 bellhousing shouldn't be too difficult or expensive.
I too wanted to use a later cast iron bellhousing with driver side clutch fork because they are cheap and plentiful. But when I set the engine into the truck I saw that there was no room for the clutch fork. The cab floor/firewall drops right down almost on top of the driver side of the bellhousing. So I went and found a 60-62 V8 bellhousing and all is well. This also allowed for a no hassle installation of the slave cylinder and push rod. I'm done with this part of my build, so if you'd like to see this type of set up feel free to come by and check it out. I'm pretty close to Santa Cruz, at Summit Rd and Hwy 17. Shoot me a PM if you're up for it. I'm home all weekend. l'd also say that the factory bellhousing crossmember is probably going to need to be removed. You'll need a crossmember for the rear of the NV4500 anyhow and the factory one will probably be in the way. |
Re: 62' GMC 3/4 ton project
3 Attachment(s)
She's starting to look like a truck again!!!
|
Re: 62' GMC 3/4 ton project
Looking good!
|
Re: 62' GMC 3/4 ton project
Shiny! :metal:
|
Re: 62' GMC 3/4 ton project
Thanks guys! It definitely looks better in the digital images.
|
Re: 62' GMC 3/4 ton project
5 Attachment(s)
Spent some time getting the engine and transmission in and built a custom crossmember for the NV4500. The PO is a professional welder so being as I'm not I will take the crossmember to him for final welding. I wasn't sure of the driveshaft angles and all that so I built a fair amount of adjustment into the new crossmember just incase I need to make some adjustments up or down. Took the driveshaft to a shop in San Jose (South Bay Driveline) to get it shortened, rebuild and balanced. Next is to finish the cab work and try to get it sitting on the frame. I'm hoping the cab fits around the new transmission, I guess that's the chance I take for changing the transmission half way through the build.
|
Re: 62' GMC 3/4 ton project
5 Attachment(s)
Just a few pictures of the progress and I'm living in OR full time now.
|
Re: 62' GMC 3/4 ton project
5 Attachment(s)
Just a few more.
Hopefully I'll have some time to clean the new garage and get some thing done on her soon. I guess my first job will be finding a job. |
Re: 62' GMC 3/4 ton project
Everything's looking good Ryan!
|
All times are GMT -4. The time now is 05:53 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com