New Hickey 69-72 Blazer Jimmy roll bar
 

UPDATE!! AGAIN

I know that some people would like a roll bar for the summer. These will be just like the originals Hickey bars. 1.75"OD and .125 wall tube. The main hoop will come in three pieces left, center and right. Will include 4 floor plates and the 2 angled pieces to mount to the front of the wheel wells too. Raw steel finish only. I'll include tube inserts so you can weld them together for a seamless look.

Price is $250 for the front or rear.

Shipping will be $25 to $50 depending on how far from Michigan you are.

Please spread the word!

Re: New Hickey 69-72 Blazer Jimmy roll bar
 

Can you post a picture of one? Even an original for reference?

Re: New Hickey 69-72 Blazer Jimmy roll bar
 

Couple of questions.
1) How did you get the dimensions to make this one?
2) Have you done a test fit in a Blazer of one of these you have built yet?

Thanks. Jeff.

Re: New Hickey 69-72 Blazer Jimmy roll bar
 

The easiest way. I copied my roll bar. Yes I have, test fit. My roll bar has fit perfectly in my blazer since 1970-71.

Re: New Hickey 69-72 Blazer Jimmy roll bar
 

Any chance of getting a pic with one on your Blazer?

Thanks!

Re: New Hickey 69-72 Blazer Jimmy roll bar
 

I'll get one tomorrow

Re: New Hickey 69-72 Blazer Jimmy roll bar
 

Sorry for the delay pictures coming today

Re: New Hickey 69-72 Blazer Jimmy roll bar
 

Re: New Hickey 69-72 Blazer Jimmy roll bar
 

Re: New Hickey 69-72 Blazer Jimmy roll bar
 

Re: New Hickey 69-72 Blazer Jimmy roll bar
 

Re: New Hickey 69-72 Blazer Jimmy roll bar
 

Do you have any pictures of all the pieces and whats the total weight shipped?

Thanks Carey

Re: New Hickey 69-72 Blazer Jimmy roll bar
 

Could I get pitcures of the pieces thanks

Re: New Hickey 69-72 Blazer Jimmy roll bar
 

I don't have pictures of the pieces yet because they have not been made yet. Production will start this week I hope. I just sent the PO on last Tuesday.

Shipping weight will be about 40-45 lbs.

Re: New Hickey 69-72 Blazer Jimmy roll bar
 

Sorry no picture of the pieces till their made. But you would receive the 4 floor plates, main hoop in 3 pieces (left, center and right), 2 angled tubes and 2 tube inserts for the main hoop joints.

Re: New Hickey 69-72 Blazer Jimmy roll bar
 

in stock, will start shipping next week.

Re: New Hickey 69-72 Blazer Jimmy roll bar
 

This is the kit plus 4, 3/16"x5" square floor plates not shown.

Attachment 1382843

Re: New Hickey 69-72 Blazer Jimmy roll bar
 

I would have hoped the plates where welded n angles were cutt on support bars

Re: New Hickey 69-72 Blazer Jimmy roll bar
 

I have installed about 25-30 cage kits from 5 or more companies, never have I seen the floor plates pre welded. As far as the support pieces not having the angle cut, again it is common to notch and trim your tubes for a perfect fit to your truck. If you would like a refund just send me a PM. No problem at all.

Re: New Hickey 69-72 Blazer Jimmy roll bar
 

Following...

Re: New Hickey 69-72 Blazer Jimmy roll bar
 

Nice work.

Re: New Hickey 69-72 Blazer Jimmy roll bar
 

ttt

Rear roll bar is now ready. $250 plus shipping $25-$50 Shipping from West Michigan.

Are these still available? Or does someone have the dimensions for one
Posted via Mobile Device

Re: New Hickey 69-72 Blazer Jimmy roll bar
 

You can find the roll bars on ebay, you can find the dimensions on this forum, I may have the link but will have to look