Heater help!
1 Attachment(s)
Well i need help. Surprise surprise right? On my 77 k10, i put a new blower motor and fan blade (metal) but i have nothing through the vents. I have attached pic of my outside wiring where i think the problem is. Also my heater core hoses are only... Lukewarm... Thought they were supposed to get hot as hell?
|
Re: Heater help!
It appears you don't have vacuum connected to your amplifier on the firewall. The black round thing in the front left of your picture. That could keep your blend door from opening. Warm, not hot heater hoses sounds like a bad thermostat.
|
Re: Heater help!
I'll get a new thermostat. Little assurance. It has a vacuum hose goin to the ball thing it goes over the box. Think it goes to the back. But my blower doesn't turn on at all :/
|
Re: Heater help!
So are you not getting power to the blower motor? Also you might want to flush the heater core while you are in there and change the thermostat as you said.
|
Re: Heater help!
See the thread here titled "Heater Blower" about possible causes why your blower motor isn't working. The black round vacuum reservoir only appears to have one vacuum hose attached to it. It needs a vacuum hose from the carb to it then another hose goes inside the cab to the heater control.
|
Re: Heater help!
Well small update. I put i a bew thermostat 195 since it's getting cold this timma year. Hoses only get kinda warm not hot :/ same cab before did this too :(
|
Re: Heater help!
Its possible, though not probable, that the heater core is nearly completely clogged so that little to no fluid is running through it.
Also, did you check the blower fuse? |
Re: Heater help!
Will check fuse tonight. Other than this n my driveshaft i'm ready to rock. Where does the big red wire go?
|
Re: Heater help!
Looks like the wire that goes down to your starter but i can't really tell but that would be my guess.
|
Re: Heater help!
So it comes out of the firewall by the ac and heater wires to the starter? Seems odd. Does the vacuum line go to the front port or back port on the ball thing?
|
Re: Heater help!
Well i can't tell where it's coming from in your picture but the connector on the bottom and thickness of wire looks like the one that goes to the starter.
|
Re: Heater help!
Red wire might be the one that runs across the firewall to the junction block.
|
Re: Heater help!
Think i'll look behind the heater box tonight. Surprisingly ye heater core doesn't leak or anything. What about all the green wires? Can i cut-n-tuck them? I won't reinstall the ac.
|
Re: Heater help!
Honestly, all of that wiring is a little scary looking. You might want to get a wiring diagram and clean up some of those wires. Its probably not a good idea for us to be guessing what wires are what. That could lead to some serious problems if wrong.
|
Re: Heater help!
It starts n runs string n fine. All lights work just the heater >:/ aggrivating! I'll look tonight for one n i'ma try n get ridda as much as possible for simplicity
|
Re: Heater help!
is there a vacuum controlled valve for hot water to the heater core? if so, bypass it and see if it gets hotter. also the heater hoses have to be hooked up where the return hose goes to the water pump and the supply hose to core comes from intake. I think thats the way it goes.
|
Re: Heater help!
Fist thing to do would be to check the power at the blower and go from there. That box the wire to the blower motor comes out of is the relay switch, that would be the next thing. Sometimes you can hit the relay switch and get it going for a bit. There is also a resister but high power is not affected by this.
Get the blower working and then go from there. |
Re: Heater help!
|
Re: Heater help!
So the red goes to the other side (left) of the junction block... And green goes to... Evap control switch. Do i need the evap switch for the heater or no?
|
Re: Heater help!
Not sure you need that if you are not using your AC. Did you check the power to the motor?
|
Re: Heater help!
I will tonight after work. :metal: i'll run the red wire over to the junction n see how it all works. But even after a new thermostat i only get lukewarm hoses. It's a 195, i'm afraid to put anything higher in.
|
Re: Heater help!
Are you driving this truck trying to get it up to temp or just letting it set and idle. I have had a couple of vehicles that wouldn't get very warm until they were driven. It should still be getting some temps going though.
|
Re: Heater help!
2 Attachment(s)
lower right of pic the (brown 50),dosn't that go up in the dash with the radio wires?
if you can test it, to run ok ,from the batt I'd check the blower coils |
Re: Heater help!
1 Attachment(s)
Idk if it is or not. UPDATE: Plugged in the vac hose to the FRONT of the ball and the back going into the cab somewhere, also put the red wire onto the junction block and no difference :(
Updated pic showing more green wires unpluged what is that 2 pronged thing on the bottom right of the box? Needed? |
Re: Heater help!
Quote:
|
All times are GMT -4. The time now is 10:41 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com