Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

Yes, its fine to put in on the passenger side on a downflow. We've been building this style like that for a decade with no issues.

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

we appreciate the support!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

back up top!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

up top again

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

back up again

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

remember to ask for your discount when ordering

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

back up top!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

up top!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

Thanks for the continued support, we appreciate it!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

Hi,
I have a 86 2wd C10 with a 4.8/4L60. I am looking for a reliable radiator/fan setup (this is a daily driver), I have a VA air conditioning unit. Can you please give me recommendations for a good radiator here in the desert? The engine is stock W/O any upgrades. ��
Thanks ��

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

Sure, our standard radiator will be fine for that. With A/C and being in the desert, I'd go with our upgraded single 17" dual-speed fan. I assume you'll use the PCM / LS harness to control the fan?

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

I have an LT L83 with Ac and in Tx, what would you suggest and could you PM me the cost please?
I would like the best shroud & fan option also.

Thanks
Posted via Mobile Device

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

I see your located outside of Atlanta I am in Athens,
I am working on a 1970 Blazer 2WD factory 6 cylinder but PO dropped in a 454 stroked to a 496 and automatic no ac.....not hooked up yet so not running

What radiator, shroud combo do you have for this setup

Thanks

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

sending PM shortly.


Does the 6-cylinder use the same radiator mounting / supports as the V8? If the width and mounts are the same, it'll be easy. If you wish, you can PM me pictures and a few measurements to confirm.


Sorry for the delayed reply, the forum didn't notify me there were replies.

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

up top!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

we can build radiators for most any application!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

back up top!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

up top again!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

remember to ask for your discount when ordering!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

thanks for the support!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

back up top!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

thanks for the orders!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

we can also build radiators for most any application!

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

Looking for a radiator, shroud and fan for a 1966 C20 build that will be running a 400 SBC built for ~500hp.

Re: RnD Fabrication 1963-1966 Chevrolet & GMC C10 / C20 Aluminum Radiators!
 

We can easily build that! pm me your zipcode and I can put together a full quote with recommendations.