Project 6 Point Oh
I've decided to start a build thread after working on my 72 K5 Blazer for almost two years. I was just going to get it drivable and not do a restoration, but I couldn't stop myself LOL. Now I'm in the process of a frame off restoration, and dropping in a 6.0 LQ9 and a 4L60. I don't get much time off from work, so the process is slow, but steady. I was a mechanic years ago and worked on tons of these old trucks, but I got out of the business way before LS motors were introduced, so I will be needing advice on that end. I've taken tons of pics along the way and will post a few. Three things I don't do are transmissions, and paint and body work. Everything else I plan on doing myself. :metal:
|
Re: Project 6 Point Oh
1 Attachment(s)
Attachment 1232300
This is what it looked like when I went to buy it. Sitting outside with no top on, roll bar in backwards, wiring pulled out, no brakes, and barely running. The truck looked good from a distance, but was really rough up close. The floor was toast but I couldn't tell because of a thick coat of fiberglass covering the damage. The gas door install was horrible and covered up by LOTS of bondo. The patch for the original gas neck hole was a thick layer of bondo too. |
Re: Project 6 Point Oh
1 Attachment(s)
|
Re: Project 6 Point Oh
1 Attachment(s)
Attachment 1232318
I think the only thing electrical that worked was the ignition switch and an external horn button. lol |
Re: Project 6 Point Oh
1 Attachment(s)
Attachment 1232337
Got the double wall top back on it and got it home. I don't think the top had been on it in a long time. It had been outside with no top, exposed to the elements for no telling how long. |
Re: Project 6 Point Oh
1 Attachment(s)
|
Re: Project 6 Point Oh
1 Attachment(s)
Attachment 1232339
Got the front clip off and the motor and trans out. |
Re: Project 6 Point Oh
1 Attachment(s)
Attachment 1232345
Found a 2003 6.0ltr out of an Escalade with 77K on it. |
Re: Project 6 Point Oh
1 Attachment(s)
Attachment 1232347
I could tell there was going to be issues lol. |
Re: Project 6 Point Oh
1 Attachment(s)
Attachment 1232351
Looks like it used to be white. The SPID was gone, so I wasn't sure. |
Re: Project 6 Point Oh
1 Attachment(s)
|
Re: Project 6 Point Oh
1 Attachment(s)
|
Re: Project 6 Point Oh
1 Attachment(s)
Attachment 1232366
The wiring had more butt connectors and electrical tape than I'd seen in a while.:cool: |
Re: Project 6 Point Oh
Looks awesome!!
|
Re: Project 6 Point Oh
Vin plate match title? Ill watch
|
Re: Project 6 Point Oh
1 Attachment(s)
Attachment 1232367
LS motor mount from Pacific Fabrication, 4L60 to NP205 adapter from Advance adaptors, and a Ididit tilt steering column. |
Re: Project 6 Point Oh
Yes VIN plate does match.
|
Re: Project 6 Point Oh
1 Attachment(s)
Attachment 1232368
Oh boy:waah: |
Re: Project 6 Point Oh
1 Attachment(s)
Attachment 1232369
Rusted out inner fender and a bonus quart of oil! |
Re: Project 6 Point Oh
3 Attachment(s)
|
Re: Project 6 Point Oh
1 Attachment(s)
|
Re: Project 6 Point Oh
1 Attachment(s)
Attachment 1232382
At least the rocker boxes underneath were good. |
Re: Project 6 Point Oh
1 Attachment(s)
Attachment 1232383
They had brazed a piece of metal behind the original gas neck hole, then filled the rest with bondo!!! :dum: It looked like a hockey puck went in there. |
Re: Project 6 Point Oh
1 Attachment(s)
|
Re: Project 6 Point Oh
1 Attachment(s)
Attachment 1232390
That's gonna have to be replaced and redone correctly. So far this truck needs everything. |
All times are GMT -4. The time now is 07:07 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com