Re: My 1970 GMC Project
Quote:
|
Re: My 1970 GMC Project
How much of that cab are you going to have to fix to make it right? Is there a supplier up there that you get patches for pretty cheap?
|
Re: My 1970 GMC Project
Quote:
|
Re: My 1970 GMC Project
I gotcha. Yea it's a lot of work! When I'm working on my stuff I'm trying to figure out how body shops do it so much quicker... and how people could afford that! Good gosh I spent all weekend shaving my drivers side cowl vent and I'm about half done. Unbelievable!
I have to replace all that stuff on my cab, plus some. I finally called a distributor in MN last week and got talked into a complete floor since it was basically like $75 more than all the patches added up. I was gonna suggest something like that for you too. There is still time to reconsider! Lol |
Re: My 1970 GMC Project
Quote:
|
Re: My 1970 GMC Project
I'm in the same boat as you man... more time than money. That's why I'm doing all these odds and ends on the cab that don't cost me anything except grinder discs.
Get going on that thing then!! :metal: |
Re: My 1970 GMC Project
Quote:
|
Re: My 1970 GMC Project
3 Attachment(s)
Well I'm thinking that it is time for an update on here, even if it doesnt exactly pertain to the truck. I got a little busy for a while there with a sidejob. Now that it is all wrapped up, Im back in the shop. Im not quite to the point of working on the truck again yet. Ive decided that the shop needs a few upgrades. I now have my old compressor tank hooked up to the new compressor to double my air capacity. Ive also been working on putting up a fume extractor. Also I was fortunate enough to find a metal frame on wheels at work that will be perfect for a cab cart so Ive been modifying that the last couple days. Here are some pics of the progress.
|
Re: My 1970 GMC Project
2 Attachment(s)
Tonight I finished up my cab cart! :) SO much nicer working at a sitting height. I built it so that once I have the cab support replaced, I will be able to flip it right side up and bolt it on. I also did a test fit on my footwell panel and I am pretty happy with it. Just needs some small adjustments to make it right. Hoping that I will be ready to weld it in soon!
|
Re: My 1970 GMC Project
4 Attachment(s)
Today was a good day :) I got my footwell panel cleaned up, shot it and surrounding area with weld through coating and welded the sucker in! :metal: Im happy with the results, only ended up with two pinholes in my weld.;)
|
Re: My 1970 GMC Project
5 Attachment(s)
Hello everyone. I spent an hour in the shop after work today and managed to get my floor pan close to fitting. Still gotta beat it around a bit more yet and do a little trimming.:lol: The second picture shows where I really had to unleash hell on it. ;)
|
Re: My 1970 GMC Project
4 Attachment(s)
More progress to report. :) I was trying to figure out how I could bend the flange at the front edge of my floor pan. I thought about a brake but it was not flat enough to put in a brake. Then I found some vise grips that would work perfect! Rather than buy them, I figured I would be resourcful and re purpose a pair of old vise grips that my dad had lying around. Couple pieces of scrap metal and about 2 mins of welding and bam! :lol: So now that Ive got that out of the way, the slow process of trimming down to fit slowly so as not to cut too much off can continue. Starting to see some good progress here! :metal
|
Re: My 1970 GMC Project
Nice work. Ton of metal repair you're having to do. You may not be happy with your welds, but I'm really impressed with your cuts. They seem super precise. What are you using?
|
Re: My 1970 GMC Project
Quote:
|
Re: My 1970 GMC Project
5 Attachment(s)
And we now have a floor pan!:metal: I finished up all the prep on my flange and got it fitting the way I wanted and welded her up. Still have a little grinding to do by the transmission tunnel then its on to the next piece.
|
Re: My 1970 GMC Project
Very cool stuff! I like the vise grips! I was going to do that but after looking at harbor freight the price was too good. The progress you are making is making me jealous! At this rate you will be done in no time!!
|
Re: My 1970 GMC Project
Quote:
|
Re: My 1970 GMC Project
5 Attachment(s)
Well Ive been busy the last couple weeks in the garage, unfortunately not working on my truck though. Not till today anyway. I did a good clean and decided that two toolboxes was pretty overkill, so I sold the smaller one and extended my bench. After a little bit of electrical work, I got myself setup with a mini fridge in the shop! :metal: I also got myself a new shop stereo. Bought a new one for the house so the old on is in the garage now. Complete with subwoofer and all. Now that thats all wrapped up, Im back on rust repair. Got the other portion of my inner rocker welded in today!
|
Re: My 1970 GMC Project
5 Attachment(s)
Back at it. The last couple evenings Ive been in the garage working on the truck. Ive got most of the floor pan welds ground down. Then I really took some time comparing the arch of the new floor pan to the passenger side and found out that the new floor pan has a 3/8" high dome to it. So I have been heat shrinking the dome down to where it needs to be so the cab support bracket will fit properly to it. Its proving to be alot of work but it is definatly worth it. Now I get to take all the wrinkles out of the aftermarket floor pan and it is starting to look more like factory now. :metal:
|
Re: My 1970 GMC Project
2 Attachment(s)
I finished up with my heat shrinking last night. Back to the grind now. :lol: Ive got a full day planned in the shop tomorrow so hopefully I can finish up with grinding my welds and possibly get some more of the old cab support off.
|
Re: My 1970 GMC Project
5 Attachment(s)
So it finally happened. I couldnt take it anymore! Flux core was driving me crazy! So I went out and got a gas setup :metal: So much nicer! But now Im back at square one....learning to weld again as this seems like a different tequnique is required.:waah::lol: Here are some pics of my first go.
|
Re: My 1970 GMC Project
Dude you are a brave soul for taking on that cab, kudos to you. It looks like you are getting the welding down, honestly the hardest part (in my opinion) with patching is knowing how to get the new metal to fit right and it looks like you have that part down. Are you using anything to seal up the raw metal in some of those pockets before you cover them up?
|
Re: My 1970 GMC Project
Quote:
|
Re: My 1970 GMC Project
Your repairs are looking good. Chasing pinholes can take forever. If you didn't hammer stretch out the weld seams, that will contribute to the floor becoming crowned. (Though, I have found that reproduction pieces aren't perfect). The long weld seams shrink along the length of the seam. That causes the metal in the center to buckle and crown, because it has no where to go. You can usually hammer out a seam, and only need minimal shrinking in the center. But hey, I understand, that is a hard seam to reach and hammer out. The more experience you get at working and welding sheet metal, you will learn how it behaves.
|
Re: My 1970 GMC Project
Quote:
|
Re: My 1970 GMC Project
4 Attachment(s)
More good news! We were tearing out a poorly built mezzanine at work yesterday and I scored 2 new light fixtures for the garage. So I called my dad over last night and we got them up. Almost need sunglasses now:lol: Just gotta wait for 2 more to turn up somewhere and Im laughing.
As for the truck, Ive been slowly chasing pinholes from the damn flux core:waah: Though I did find some time between letting the compressor rest to strip the e coat off of the bottom of the floor pan. Soon enough Ill be cutting out the rest of that rotten support.:metal: |
Re: My 1970 GMC Project
2 Attachment(s)
Today was a good day! Got the rest of the pinholes filled! :metal: Now its on to bigger and better things, aka cutting out the rest of the rotten support. :lol: Also found some more light fixtures in our warehouse and the electrican told me if I need them they are mine. So bright I almost need sunglasses now.;):lol:
|
Re: My 1970 GMC Project
Nice! I like the new shiny metal... make the rest of the floor look like that! Did you get any "oil canning" on that floor pan after you got it all welded in? What's the process of getting your supports in - are you going to have to reinstall the brace from back of cab to front first? Or weld in your supports first?
Btw did you get another blast of winter up there? We did last week and today was below zero with the wind. Thought we were on to the next season... |
Re: My 1970 GMC Project
Quote:
We did get more winter, not just a blast though. It is like an explosion. We have been breaking 100 year old cold records. Currently as I type this it is -14°, -20° with wind chill. :canada: :waah: |
Re: My 1970 GMC Project
Quote:
That sounds like a good plan for the supports. Holy cow! That's a bit cold for this time of year I'd say. We are also breaking records for the coldest temp. I need it to warm up so I can get outside and do more sanding!! |
Re: My 1970 GMC Project
Quote:
I also need it to warm up so I can drag the rest of my truck home. |
Re: My 1970 GMC Project
Quote:
|
Re: My 1970 GMC Project
Quote:
|
Re: My 1970 GMC Project
5 Attachment(s)
Got some more rust cut off. I started on the passenger side and got most of the rocker cut off and started drilling out the cab support. I also figured that I might as well pull the seat backing plate of and get rid of any rust betweet it and the floor pan before re installing it. Hopefully by next weekend the rest of the cab support is out.
|
Re: My 1970 GMC Project
4 Attachment(s)
Lots of progress made in the last two days. We are a little slow at work right now so I decided to take an unpaid day off yesterday. Which meant GOODBYE RUSTY CAB SUPPORT:lol: well almost. There is about two feet of the rear crossmember left. It is not a fun procedure thats for sure. I ended up having to cut the thing into a bunch of smaller pieces to get the welds to break loose. After all that I decided that the rest of it can stay there until it is in my way.;) So onto more floor pan replacement. I got the rear section cut out now and I just need to fine tune for fit. There were some minor diffrences between the old and new pieces but I think that was mostly because of a few small changes made to the 71-72 cabs. Anyway I got them all sorted out now. Hopfully Ill have it tacked in place tomorrow evening.
|
Re: My 1970 GMC Project
That is a lot of hard time consuming work, but you are killing it.
|
Re: My 1970 GMC Project
Quote:
|
Re: My 1970 GMC Project
5 Attachment(s)
Pretty happy with my progress tonight. Ive got the rear floor pan mostly tacked in place. Only thing that stopped me from finishing is an alignment issue. Ive measured, meausured and measured again to confirm that the cab mount holes are in the proper spot which they are. Yet for some reason the outer side of the pan near the rocker/cab corner are not lining up. It is almost 1/4" out but I cant figure out why. It is tight to the pillar where it is supposed to be so I dont know what my next move is going to be as of yet. Ill have to go visit my dad tomorrow and see if he has any ideas.
|
Re: My 1970 GMC Project
4 Attachment(s)
Ok I got that figured out. After lots of measuring and double checking, I found that the outboard side of the pan was dropping. So after some discussion with OriginalThor and my dad, I made a decision. I made a releif cut that allowed me to make the correction and carried on welding. Still quite a bit of welding left but then I can finally say that the driver side is done! :metal:
|
Re: My 1970 GMC Project
Man you are kicking butt on this project, nice work!
I remember just to do one side of a cab replacing inner and outer rockers, kick panel and a cab corner, was something like 40hrs of work for one side. You've done a lot than that on this project so far and have amazing results, rock on! |
All times are GMT -4. The time now is 08:16 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com