gonna find out my rear end ratio....
 

i dont have a tag on the diff bolts..

if i take the cover off to read the ring gear..will i be able to find it? or am i better off to spin the whels and count the driveshaft rotations? and how much does it cost to rebuild a rearend? (roughly)

thanks!

Re: gonna find out my rear end ratio....
 

Pop the cover and read the ring gear. Turn it around until you get to the numbers and wipe the oil off of them. There will be two numbers separated by a colon. Divide the first number by the second and you will have your ratio.

Re: gonna find out my rear end ratio....
 

i got 1 tire jacked up (not posi) ok i turn the tire count the driveshaft truns and time that by 2 right?

im confused ima go out there do it and write it down then post it here lol thanks


ok thats what ima do to my donor rearend thanks! will any oil leak out?

Re: gonna find out my rear end ratio....
 

What you do is to turn the pinion yoke (driveline) exactly one time and count how many times the tire goes around. It's actually a pretty darn accurate redneck way of finding the ratio. Chalk or mark the tire somehow.

If it's goes around 3 1/2 times, it's about a 3.50

If it only goes around a little more than 3, it's a 3.07 or 08

I like it when they go around 3 3/4's times cuz that's your 3.73

and so on......

Re: gonna find out my rear end ratio....
 

30 56

30 being the tire spins

56 being d shaft


i came up with 3.73 is this correct? thanks goin into the weeds with the snakes to calcualte the other rearend...

Re: gonna find out my rear end ratio....
 

I`m not sure,did you spin it that many times?
Did you do what TX Firefighter suggested.It`s downright fool proof.YES,oil will leak out,if there`s oil in there.Get some fresh lube,put a pan under there,and start taking the lowest bolts out all the way.It will start draining.Go ahead and start taking all the others out while it`s draining.If draining is slowed down you can pop the cover off with care.It can take a long time to stop running/dripping.Check the condition of the lube and get back to us.

Re: gonna find out my rear end ratio....
 

Not sure K and I know what you are talking about. Just what exactly is the 30 and what is the 56?

Re: gonna find out my rear end ratio....
 

uhh dang lol i forgot

its been a few hours..but i think 30 is tire spins and 56 is d shaft spins...this is before ANY MATH IS INVOLVED

Re: gonna find out my rear end ratio....
 

Here's a shot of my 4:10 rear end.

The text reads, 7 3 70 DANA 30360 A306 41-10

I am guessing the first three are the build date, the next the model and material and lastly the ratio.

Re: gonna find out my rear end ratio....
 

You are making it too tough. You just need to mark the tire and spin till the driveline U joint makes one complete circle and at the same time count how many times the tire goes around. You will end with a fraction on the last spin.

Re: gonna find out my rear end ratio....
 

The numbers represent the number of teeth on the ring gear and the pinion gear.

Re: gonna find out my rear end ratio....
 

So do my numbers add up right?

can somebody tell me?

Re: gonna find out my rear end ratio....
 

Where did you get your numbers from? The gear or did you spin the tire that much?

Re: gonna find out my rear end ratio....
 

And isnt it how many times the drive shaft spins to make one tire rotation?

Re: gonna find out my rear end ratio....
 

Too many Beers......................YES!!!!!!!!!!

I was bass-acwards!!!!



I can say though that that pinion doesn not have either 30 or 56 teeth!!!!

Are you counting the spider gears??? The pinion you can barely see because the carrier covers it up. If you took the cover off, just look at the last numbers on the ring gear like "big blue" showed us.

Re: gonna find out my rear end ratio....
 

haha It happens prostreet

Re: gonna find out my rear end ratio....
 

I think I understand what you did, it is the same as prostreetc10 said except you only lifted one tire and you turned the driveshaft enough times to make for round numbers. so if you turned the yoke 56 times and the tire turned 30 times then you divide 56 by 30 which equals 1.867 but the ratio is actually twice that because the spider gears cause the tire to rotate twice as fast as when both tires spin, so you have to multiply 1.867 by 2 which equals 3.734, so I'm pretty sure the rear is a 3.73. Hope this makes sense

Re: gonna find out my rear end ratio....
 

If it`s 3.73 ratio you will spint the wheel 100 times to the driveshaft`s 373 times.Or,if you`re lazy,you could just spin the wheel once and the driveshaft will spin 3.73 times.Or, 3 and 3/4 turns.And if you`re real lazy,I can sell you a tab for whatever ratio you want.:lol:
Or,you could read all the suggestions and try those.It`s been well explained,I think,already.:cool:

Re: gonna find out my rear end ratio....
 

haha signature material ^^

Re: gonna find out my rear end ratio....
 

No, on a 1 legger rearend, you must spin the tire two times. You must double it. For instance, you spin the tire twice, you will find the pinion spins 3.73 turns.

Or, you can buy 2 quarts of lube, a tube of silicone, and a can of crab spray cleaner and do it right. Who knows how old and nasty the fluid in there is. You don't want you bearings running in dirty grease do you ? Do it right. It won't take 15 minutes.

Re: gonna find out my rear end ratio....
 

This is sorta funny. I think you should buy a new ring and pinion and then it will be what you want it to be

Re: gonna find out my rear end ratio....
 

Probably the easiest way to find out what you gear ratio is.....is to pull #3 and #7 spark pull. Take the divided gap of both and times it by your carb CFM. Then you take (in inches) the distance from the front of the INSIDE of your bed and measure back to the full cooler of beer. Now....add up the EMPTY beer cans that are still cold. Take Pie R Squared and times that by the model number on your left front head light. That will usually give you the gear ratio of your rear end down to about +/- .00000000021

Re: gonna find out my rear end ratio....
 

prostreetc-10 You forgot to and the number of lug nuts you have

Re: gonna find out my rear end ratio....
 

jacfourteen, i hope you understand, and you others...sorry for my stupidity lol........does anybody else agree with jacfourteen

Re: gonna find out my rear end ratio....
 

oldblue1968chevy Sorry this got out of hand. Thier's 2 parts to this, 1st you just asked a good ? about how to determine rear ratio's. Then the other part where if you ask the same ? to 15 diff. people you get 15 diff answers. That's where it gets funny. So it's got nothing to do with stupidity on your part. There are many diff personality's on here most good and some jerks. Happy 4 oldno7