Thread: pdx-sanity66
View Single Post
Old 10-09-2021, 01:40 PM   #841
pdxhall
Senior Member
 
pdxhall's Avatar
 
Join Date: Mar 2011
Location: Tucson, Arizona
Posts: 2,050
Re: pdx-sanity66

This is the rest of the previous post. Again, this is for my personal record and not meant to bore anybody.
*Bumpers and brackets
1. Front—stock chromed with original brackets restored
2. Rear-- 67-72 Chev, new chrome with new 67-72 brackets
Wiring
* American Autowire Classic Update completed wiring kit
1. Part #500560
2. I made an aluminum fuse box/fan controller mount and mounted the assembly on the driver’s side inner firewall
3. Oil sender, temp sender, alternator, tach sender, and distributor wiring complete.
4. Dual fan to relays to Dakota digital controller wiring complete
5. Battery, starter/solenoid wiring complete
6. Carb auto choke wiring completed
7. Front lights and horn done. Original hardware restored with new bulbs and relays
8. Rear lights done. Original hardware with new pigtails and and conversion to LED.
9. Fuel gauge sender wired.

Cab Body Work
* Stripped all parts from cab
* Replaced passenger side fresh-air box
* Replaced rusted out areas of the passenger side floor, kick panel, inner rocker, lower door pillar, and patched and re-installed stock outer rocker panel
* Replaced rusted out areas of the driver side floor, kick panel, inner rocker, lower door pillar, outer rocker panel
* Patched corners of floor where the gas pedal sits and the opposite side
* Cab bottom cleaned, stripped, prepped, and painted with epoxy primer and then U-lol Raptor Bed Liner.
* Upper door pillar seams and roof to windshield seams filled
* Welded and finished seams in door pillars and rockers
* Stripped, filled all unneeded holes, smoothed, and epoxy primed the firewall and then painted it with Eastwood’s 2K Ceramic Under Hood black urethane.
* Stripped, sanded and epoxy primed all interior surfaces. The ceiling and the back area painted with Eastwood Aluma-blast
* cleaned, prepped, dash for repaint
* Patched passenger side rear cab corner
* Seam sealed all floor areas.
* Lizardskin heat shield sprayed on floor, kick panels, and inner firewall
* Boom Mat spray sound deadener on upper inner firewall
* Rear half of the floor and halfway up the back of the cab painted with Upol Raptor bed liner
* New reproduction bed sides and front panel installed
* Inside of door openings media blasted and epoxy primed
* Doors stripped, inside bottoms patched and finished, epoxy primed
Bed
* New reproduction front panel epoxy primed
* New reproduction bed sides
* New reproduction rear cross sill epoxy primed
* Replacement original tailgate media blasted and epoxy primed
* 4 new cross sills and 1 media blasted and all 5 epoxy primed
* Bed kit ordered from Mar-k with white oak

Dashboard
* top of dash needs repaint
* Radio delete plate paint and install
* Heater control block off plate installed
* Polished/brushed stock aluminum gauge surround
* Custom black painted gauge panel
* Autometer gauges
* The Gauge panel wiring is complete with LED turn signal and bright lite indicators
* Painted glovebox door and parts and installed with new hardware
* Added a new glovebox light
* Installed gauge panel and completed wiring
* New headlight switch, ignition switch, and wiper switch installed
* Heater controls?
Exhaust
* Complete 2 ˝” dual exhaust system from header flanges to in front of rear tires with Flowmaster mufflers
__________________
Sanity'66
http://67-72chevytrucks.com/vboard/s...d.php?t=515110
Long bed, Fleetside, Small back window

I've Done So Much, With So Little, For So Long, That Now I Can Do Anything With Nothing.
pdxhall is offline   Reply With Quote