The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 06-02-2024, 12:55 AM   #1
howzzzit
Registered User
 
howzzzit's Avatar
 
Join Date: Dec 2005
Location: Kalifornia
Posts: 314
No front brakes

Driving a 72 C10 with stock front disc brakes and drum rears. Haven't changed the front pads for years so I decided to do just that. When I pulled off the pads they looked new with no wear. The piston was still pushed in like I would have done before installing new pads. This is both front brake sides. Apparently I've only been stopping on the rear all these years. What should I be looking for?
Another note. No brake light is coming on. Checked brake light switch and it's working working properly. All panel bulbs new. Both front sides have the same symptoms so I would think it's either the master cylinder or combination/proportioning valve. Proportioning valve is centered. Guess I'll change both so I only have to bleed once.

Last edited by howzzzit; 06-02-2024 at 12:06 PM.
howzzzit is offline   Reply With Quote
Old 06-02-2024, 01:05 AM   #2
franken
Registered User
 
Join Date: Jun 2013
Location: Somewhere
Posts: 3,058
Re: No front brakes

There's a valve in the lines by the master cylinder that makes fluid go to the front or rear when one end loses pressure. There's a little tool you're supposed to use when bleeding to keep the pin from moving.

http://67-72chevytrucks.com/vboard/s...d.php?t=785770
franken is offline   Reply With Quote
Old 06-02-2024, 01:15 AM   #3
Rust_never_sleeps
Senior Member
 
Rust_never_sleeps's Avatar
 
Join Date: Jun 2022
Location: San Ramon,CA
Posts: 440
Re: No front brakes

At least they never squeal
__________________
1970 C10 Custom longbed 350/350
Rust_never_sleeps is offline   Reply With Quote
Old 06-02-2024, 01:45 AM   #4
howzzzit
Registered User
 
howzzzit's Avatar
 
Join Date: Dec 2005
Location: Kalifornia
Posts: 314
Re: No front brakes

Quote:
Originally Posted by franken View Post
There's a valve in the lines by the master cylinder that makes fluid go to the front or rear when one end loses pressure. There's a little tool you're supposed to use when bleeding to keep the pin from moving.

http://67-72chevytrucks.com/vboard/s...d.php?t=785770
I did use that tool recently. I had to replace a rear cylinder. Years ago when I replaced the pads I wouldn't have needed to bleed the lines.
howzzzit is offline   Reply With Quote
Old 06-02-2024, 11:18 AM   #5
yuccales
Registered User
 
yuccales's Avatar
 
Join Date: May 2011
Location: Northern Calif.
Posts: 3,617
Re: No front brakes

Quote:
Originally Posted by howzzzit View Post
What should I be looking for?
A new set of rear drums and shoes! In all seriousness, you'll get it all worked out.
yuccales is offline   Reply With Quote
Old 06-02-2024, 12:12 PM   #6
truckster
Senior Member
 
truckster's Avatar
 
Join Date: Jan 2001
Location: Orem, Utah
Posts: 7,832
Re: No front brakes

Check the hoses. In fact, after so many years, I would just change the hoses.
__________________
I have sworn upon the altar of God, eternal hostility against every form of tyranny over the mind of man. - Thomas Jefferson
truckster is offline   Reply With Quote
Old 06-02-2024, 01:52 PM   #7
howzzzit
Registered User
 
howzzzit's Avatar
 
Join Date: Dec 2005
Location: Kalifornia
Posts: 314
Re: No front brakes

Well, took it for a ride. Slammed the brakes a couple of times. Front working now. Must have been the proportioning valve. We'll see. Thanks for the help.
howzzzit is offline   Reply With Quote
Old 06-02-2024, 02:06 PM   #8
weq92f
Registered User
 
weq92f's Avatar
 
Join Date: Oct 2016
Location: Dallas Texas
Posts: 2,975
Re: No front brakes

Quote:
Originally Posted by howzzzit View Post
Well, took it for a ride. Slammed the brakes a couple of times. Front working now. Must have been the proportioning valve. We'll see. Thanks for the help.
.

It must feel WAY better now. Put a lot of heat into the pads/rotors by stopping hard several times to bed the pads and season the rotors...then it'll feel even better.

-Kevin
__________________
67 C10 fleet fuel injected '70 402, 700r4, 3.73 posi
07 335 sport turbo 6sp
94 Trans Am GT LT1 6sp posi -- sold after 22yrs
99 540 sport V8 6sp -- sold
73 240z L24 4sp -- given to friend
68 C10 step 350/350 3.73 open -- sold
weq92f is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 03:06 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com