Need help with steering arm removal?? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**FRENCHBLUE72** · 06-04-2005, 02:08 PM

Need some help with getting the steering arm off i have the nuts off and cannot seem to get the arm off.. Any help would be great...

qksilver · 06-04-2005, 02:16 PM

do you have a torch.heat it up, gently, between rust and age, you could beat on that thing for ever and end up with just a mangled steering arm still attached! If no torch soak it in penetrating oil a couple of times over a couple of days then try it

71jimmy · 06-04-2005, 02:27 PM

Can you use a FORK to pry it apart. No, not the fork you eat with, two prongs in a wedge shape and you hit it with a hammer on the end to force it in between.

Alexis · 06-04-2005, 03:19 PM

are we talking about the one on the steering box?

if so, what i did when the puller could not do the job was make 2 angle cuts on each side where it slide onto the bolt of the steering box.

71RestoRod · 06-04-2005, 03:23 PM

Do you have it torn down to the spindle? You really have to slap it from the right side, then the left until one of the cone washers comes loose... then the others will follow.

Scrubby · 06-04-2005, 04:39 PM

When I did mine I didn't use heat or a puller. Just get a 5-10 lb sledge hammer and hit it down, then up, then down. The up and down action is what did it for me. Just hitting it does nothing. It still took a while, but after a bit the cone washers start to walk out. Then I pulled them with needle nose and it came off. Pretty much a huge pain in the ass.

**FRENCHBLUE72** · 06-05-2005, 01:22 AM

Thanks guys I used the hammer method and it freed up pretty easily....

06-04-2005, 02:08 PM	#1
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,590	Need help with steering arm removal?? Need some help with getting the steering arm off i have the nuts off and cannot seem to get the arm off.. Any help would be great... __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

06-04-2005, 02:27 PM	#3
71jimmy Registered User Join Date: Mar 2004 Location: Sacramento, CA Posts: 1,084	Can you use a FORK to pry it apart. No, not the fork you eat with, two prongs in a wedge shape and you hit it with a hammer on the end to force it in between. __________________ '71 Jimmy, 350, SM465, NP205, 2in Tuff Country lift, 33s on rallies, TBI, softtop and hardtop "If life was fair you'd be able to afford one of each and a garage large enough to house them all."

06-04-2005, 03:23 PM	#5
71RestoRod Registered User Join Date: Sep 2003 Location: Evergreen, CO Posts: 494	Do you have it torn down to the spindle? You really have to slap it from the right side, then the left until one of the cone washers comes loose... then the others will follow. __________________ 71 Blazer / GMPP ZZ383 / MPFI / 700R4 / 4-Wheel Disk / Ground-up frame off almost completed resto-mod

06-05-2005, 01:22 AM	#7
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,590	Thanks guys I used the hammer method and it freed up pretty easily.... __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

06-04-2005, 02:16 PM	#2
qksilver Senior Member Join Date: Dec 2004 Location: Southern Pines NC Posts: 3,853	do you have a torch.heat it up, gently, between rust and age, you could beat on that thing for ever and end up with just a mangled steering arm still attached! If no torch soak it in penetrating oil a couple of times over a couple of days then try it

06-04-2005, 03:19 PM	#4
Alexis Member since 2000 Join Date: Dec 2000 Location: Mountain View Ca / Mexico Posts: 7,879	are we talking about the one on the steering box? if so, what i did when the puller could not do the job was make 2 angle cuts on each side where it slide onto the bolt of the steering box.

06-04-2005, 04:39 PM	#6
Scrubby Check out GMTrucks.org Join Date: Sep 2003 Location: Boise, Id Posts: 284	When I did mine I didn't use heat or a puller. Just get a 5-10 lb sledge hammer and hit it down, then up, then down. The up and down action is what did it for me. Just hitting it does nothing. It still took a while, but after a bit the cone washers start to walk out. Then I pulled them with needle nose and it came off. Pretty much a huge pain in the ass.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.