![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Registered User
Join Date: Jun 2011
Location: Sneedville, TN
Posts: 831
|
Re: LS factory cruise control hook up
Am I correct
4 wire cruise switch ---- TAC Red - ------ ------- -12 volt Blue - ------ ------ -14/cruise on Green - ----------- -4/set-coast Yellow - -------- -5/resume-accell Then hook hot w/brake applied to - 6
__________________
High School Project I ---http://67-72chevytrucks.com/vboard/s...d.php?t=639174 High School Project II ---http://67-72chevytrucks.com/vboard/s...27#post7290427 High School Project III ---http://67-72chevytrucks.com/vboard/s...d.php?t=715832 High School Project IV (Tyler) ---http://67-72chevytrucks.com/vboard/s...d.php?t=780186 |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Dec 2009
Location: Independence Mo
Posts: 4,118
|
Re: LS factory cruise control hook up
If you're talking about the small wires coming off the actual switch inside the lever, then it's Blue- is the 12v ignition, Green- is On/Off, would go to pin #5 on the TAC, Red- is the Set/Coast, would go to pin #4, and Yellow- is Resume/Accel, would go to pin #14. And then you are correct, hook hot with brakes applied to pin #6.
__________________
My '72 short bed build. http://www.ls1tech.com/forums/conver...6-0-4l80e.html 5.3 swap into my RUSTY '71 C10 http://ls1tech.com/forums/conversion...71-c-10-a.html |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Feb 2005
Location: kalispell, Montana
Posts: 54
|
Re: LS factory cruise control hook up
We have set several of these up without using the stalk switch on hotrods. Just a toggle switch on the gray wire (on/off) & momentary push button on the dk blue to engage cruise. Just don't have resume/accel option which we didn't care about.
|
![]() |
![]() |
![]() |
#4 | |
Registered User
Join Date: Dec 2009
Location: Independence Mo
Posts: 4,118
|
Re: LS factory cruise control hook up
Quote:
![]() Posted via Mobile Device
__________________
My '72 short bed build. http://www.ls1tech.com/forums/conver...6-0-4l80e.html 5.3 swap into my RUSTY '71 C10 http://ls1tech.com/forums/conversion...71-c-10-a.html |
|
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Oct 2010
Location: WI
Posts: 347
|
Re: LS factory cruise control hook up
Well this is encouraging that I can easily have cruise with DBW.
Now someone needs to figure out how I can manually blip the throttle from the engine bay to impress my buddies when there looking at the engine with the hood up like you can on a cable setup...
__________________
1950 Chevy 3100-Transforming into a hot rod. Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=435302 |
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Jun 2011
Location: Sneedville, TN
Posts: 831
|
Re: LS factory cruise control hook up
Well it looks like I'm out of luck
my PSI harness doesn't have wires in the 5 & 6 pin
__________________
High School Project I ---http://67-72chevytrucks.com/vboard/s...d.php?t=639174 High School Project II ---http://67-72chevytrucks.com/vboard/s...27#post7290427 High School Project III ---http://67-72chevytrucks.com/vboard/s...d.php?t=715832 High School Project IV (Tyler) ---http://67-72chevytrucks.com/vboard/s...d.php?t=780186 |
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Dec 2009
Location: Independence Mo
Posts: 4,118
|
Re: LS factory cruise control hook up
Add them. You can get a wire with a terminal out of another PCM harness at a junk yard and add them to the TAC plug, then wire them up.
__________________
My '72 short bed build. http://www.ls1tech.com/forums/conver...6-0-4l80e.html 5.3 swap into my RUSTY '71 C10 http://ls1tech.com/forums/conversion...71-c-10-a.html |
![]() |
![]() |
![]() |
Bookmarks |
|
|